Honda VFR800 VTEC Coolant Flush Step by Step Guide

Подписаться 1,3 тыс.

Просмотров 4,9 тыс.

50% 1

How to change the coolant on your Honda VFR800 VTEC 2002 - 2013
If this helped you, please consider buying me a coffee to say "thank you": www.buymeacoff...
Tools you will need:
Mechanics gloves: geni.us/bKGCAQc
Heat resistant gloves: geni.us/FjnfXj
3/8" Socket set: geni.us/7mwQE
3/8" Extension wobble bar set: geni.us/a2j2B
Circlip plier set: geni.us/wOGFj
Funnel: geni.us/vpWP3kp
Drain bowl: geni.us/H2VS6Kj
Small drain tub (green): geni.us/iPSJ
Supplies you will need:
Blue roll: geni.us/NVA2AY
Replacement copper washer: Honda part 90430PD6003; Buy on eBay: geni.us/WhU3
Replacement bolt for front of engine: Honda part 96001-0602200; Buy on eBay: geni.us/eB2Cokv
Honda genuine premix coolant; Buy on eBay: geni.us/SAN6R
Online catalogue of all Honda VFR800 parts: www.bike-parts...
Disclaimer: If buy from the links above I receive a small commission which helps fund the channel.
If this helps you, please consider liking and subscribing. Any questions or feedback - please leave below!

Опубликовано:

8 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@michaelbelfast1 7 месяцев назад

I'd recommend once you drain the coolant out of the system which you did, to then flush it out with fresh water (just keep pouring water through the system to really flush out any debris lurking around all the nooks and crannies, then tighten drain plugs and fill with fresh coolant.

@FixItWithJon 7 месяцев назад

@michaelbelfast1 Absolutely agree pal. Either flush through with a hose or do multiple flushes with ionised water. Thanks for the comment - forgot to add that to the vid.

@jamesflint460 22 дня назад

Great video ! I recently changed my coolant and even when the temp hit 110 it was still splurging out, I had to top it up around 500ml after I had turned it off, do you think this is normal? Cheers

@joebloggs2228 5 месяцев назад

cracking video well done ill be following you advice when i do mine

@FixItWithJon 4 месяца назад

Thanks pal, really appreciate your tackling the time to comment 👍👍

@CraigKovatch 2 месяца назад

Great video! Can you tell me if the two drain bolts are the same part number? You listed the bolt for the front of the engine which I'm guessing is the one just above the oil filter. Is that the same as the main drain bolt (down by the shifter)?

@FixItWithJon 2 месяца назад

Really glad it helped 👍 Yes I’m pretty sure they’re the same bolt. Good luck!

@eric62backstrom 6 месяцев назад

I can't see where the front drain is. Im under my bike right this minute...

@FixItWithJon 6 месяцев назад

@eric62backstrom Sorry to hear that pal, it's not always that obvious, especially if there's any crud on the front of your engine. Have you been able to locate it yet?

@eric62backstrom 6 месяцев назад

@@FixItWithJon yes but I had to remove the oil filter to get to it. Then like a dumbass I started it up to flush everything out and I lost two quarts of oil on the floor haha

@FixItWithJon 6 месяцев назад

@@eric62backstrom Ahh buddy don't worry lol - it happens to us all. At least it was obvious what you had done wrong lol. It's the subtle oversights that are the worst.. Hope it's running sweet now 🙂

@sinohea.camachov.4040 6 месяцев назад

Now i learned how to change the coolant but does it have ti ve warm to drain it, and what about pouring water to drain all the remaining coolant?

@FixItWithJon 6 месяцев назад

@sinohea.camachov.4040 thanks for your message. Really appreciate it and glad the video helped :-) Yes the coolant does need to be warm when you drain it so that the thermostat is open, meaning that you get all of the coolant out. It also helps that it’s warm because any debris in the fluid will be suspended rather than all dragged to the bottom, helping the debris to escape from the drain hole. Yes it’s a good idea to flush the whole system with water. Ideally de-ionised water, before refilling. Good spot - I should’ve put that in the video.. Hope that helps?

@markwhitney19 17 часов назад

You should not drain coolant when it hot like that it very dangerous

@Engstreet 7 месяцев назад

What model is your VFR? IS IT 2002?

@FixItWithJon 7 месяцев назад

@Engstreet Yes it's a 6th Gen, hence the VTEC. Hope that helps?

@Troymans79 8 месяцев назад

nice vid, but there is no need to get the coolant hot to flush it, if anything its dangerous, especially for people learning maintanance

@FixItWithJon 8 месяцев назад

@backyardmechanical Thanks buddy, appreciate the feedback. Surely if you drain cold, you don't drain the coolant behind the thermostat? You need to raise the temperature in order to open the thermostat and drain the coolant from around the cylinders. If you do a partial drain then you end up mixing coolants which is really bad - and you have a high chance of an airlock problem too. Totally agree - it is not for an inexperienced person, but hopefully the video shows the difficultly level well, as well as the burn risks. Thanks again for the feedback - really appreciate it.