Тёмный

Hondata Speedo Fix Pt2: CSS or VSS, it'll work! 

VTEC Academy
Подписаться 131 тыс.
Просмотров 28 тыс.
50% 1

Hondata Speedo Fix Pt2: CSS or VSS, it'll work!
Your K-series swap transmission uses a countershaft speed sensor (CSS) instead of vehicle speed sensor (VSS). You wired in the new connector, but when you drive the car, the speedometer reads 120 MPH pulling out of the driveway and you just put 15 miles on the odometer driving around the block. That's not good, so how do you fix that?
If your car has a K-Pro ECU that was installed at Hondata, you have almost everything you'll need to fix this problem. Follow along as we show you how to wire the adapter harness so the corrected signal goes to your speedometer.
Need information on how to de-pin the ECU and C101 connectors? We've got a video on that right here-- • Budget K Swap Harness ...
Need to correct the MPH so it is accurate? The other K swap speedo video is here-- • How to Fix Your Speedo...
Like us? We’d Love Your Support!
Help Support VTEC Academy by hitting up our store for gear at vtec.academy/shop/ or help us by sharing (it’s free!) this post or others with other cool Honda people.
Nothing but Hondas. That’s exactly what you’ll find at VTEC Academy. Because Soichiro Honda’s passion for motorsports and his company’s ability to express that in the machines they produce make a whole lot of sense. VTEC Academy is a place for Honda fans who feel the same way and who seek the most accurate technical information and commentary to continue that very legacy and make whatever Honda it is that they drive just a little bit better. And faster. The editors and contributors of VTEC Academy are some of the industry’s most experienced and trusted, which means the informative, unique perspectives you need are all right here. And, like you, we’re also obsessed with Hondas. So, subscribe to our channel and hit us up at vtecacademy.com or, if you’re into social media, you can get your daily dose of VTEC Academy on Instagram, Facebook, and Twitter. We’re always on the lookout for cool, fast Hondas.
DISCLAIMER:
VTEC Academy videos are for educational and entertainment purposes. We can not guarantee the modifications performed in the video are legal in your locality. Do not do any modifications to your vehicle that will void your warranty or in any way violate your local laws. We assume no liability for property damage or injury as a result of any of the information contained in this video. Use the information provided at your own risk.

Авто/Мото

Опубликовано:

 

27 июн 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 243   
@7eamGhast
@7eamGhast 3 года назад
How does this channel only have 60k subs? SOOOO MUCH KNOWLEDGE
@BoostedDc4
@BoostedDc4 3 года назад
You’re a life saver, nothing but old post online how this isn’t possible blah blah blah, or trimming the plugs so the sensor plugs in, this is the way I want to do it and I thank you for this Brian 🙌🏽
@kemjisworld
@kemjisworld 3 года назад
Just did this on my brothers k swap! Huge help and saved a ton of money not having to buy the vss converter!
@EricDolinar
@EricDolinar 2 года назад
Was your kpro installed by Hondata?
@sensae5471
@sensae5471 3 года назад
Really close up zoom in on what you’re actually doing would really help out those not familiar with these swaps would be helpful. Awesome video Brian!
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
There is another video that has a close up of the actual de-pinning process. Look for it in the quick tips.
@jeremynance2
@jeremynance2 3 года назад
Another awesome upload love the golden knowledge here 😁👍🤘
@Jiff_af
@Jiff_af 2 года назад
Brian is the honda God 🙌
@tpbw4321
@tpbw4321 11 месяцев назад
Just did this using a 06 si trans on a PRB. Such an under rated channel. I got schooled!!!!!
@throttleproneandoregongrow5703
@throttleproneandoregongrow5703 2 месяца назад
I’m about to do this tn
@MrEGThug
@MrEGThug Месяц назад
What exactly did you do? 😂 I have a 06 rsx type s with a 04 tranny need help i need vtec again😢
@mr.knockyourbitchsocksoff5550
@mr.knockyourbitchsocksoff5550 Месяц назад
Bro how I’ve been stuck for months with no speedo, No temp gauge and no vtec smh
@ekk_rey
@ekk_rey Год назад
Very good video with useful info. Only complaint is that I wish he included everything in a single video instead of having to search for another video after learn how to use the option on kpro for the correction..
@SJ-xy3pi
@SJ-xy3pi 3 года назад
Thank you so much!!
@KawiZX6R1986
@KawiZX6R1986 3 года назад
THANK YOU!!!!
@vizcarraawd
@vizcarraawd 3 года назад
Is this only for the K Pro V4 installed by Hondata with a vehicle speed output? Or can you do this to any KPro 1, 2, 3, 4?
@josedelgado4462
@josedelgado4462 Год назад
So I did saw your video on this subject and I have a question. Im running an 04 accord five speed on my 95 hatch. Does the speed sensor has to be repinned in order for the speedo to work after you unplug the wire and run the new wire to the Kpro ECU?
@augiegonzales7025
@augiegonzales7025 2 года назад
Do you have a video when using a VSS on a 05 accord transmission with a RSX harness. I was told I need a converter for my speedometer to work
@punkaddic
@punkaddic 3 года назад
Thank you Brian ! Very good info. Where do you get get your power from for the css ? I remember you saying it uses different voltage than the vss
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
You get the power and ground from the TPS wiring.
@ariesr4883
@ariesr4883 3 года назад
Mostly small components use a 3-5v reference.
@Boostlee2023
@Boostlee2023 11 месяцев назад
Also, brian don’t tell you this.. they just feed you enough information to fuck your shit up.. you must run the wires individually to the speed sensor, or you can do like I did and do it at the ecu plugs and feed your alternator 5v and jump through a pile of hoops trying to figure out why your shit isn’t charging! Thanks Brian! 🖕🏻
@aundrek7515
@aundrek7515 2 года назад
I have a k20z3 engine/trans swap going into an mr2. Everything will be run on the 02-04 rsx type s engine harness. The speedometer on the mr2 is ran on the abs system. As far as the hondata k pro. Does it need this signal for the engine and trans to function correctly outside of the use of the speedometer or can I run it without this working correctly??
@kyranwoodbury5300
@kyranwoodbury5300 Год назад
Right if using that info and covert the rsx harness like that. How do you go about pinning and wiring the vss sensor with the rsx harness? Because it seems like you totally ditching the signal wire, so how does the ecu give the Kpro the signal from the sensor? Any help would be appreciated
@nathen7330
@nathen7330 3 года назад
I am in the process of doing this. Idk if it was covered but you make sure your countershaft speed sensor is receiving a 5v refrance signal like it was designed, simply splicing the countershaft speed sensor plug on is incorrect because the differential driven speed sensor receives 12v
@Brian-qe5rl
@Brian-qe5rl 3 года назад
How to make it receive 5v?
@kpwr6197
@kpwr6197 3 года назад
@@Brian-qe5rl map sensor has 5v ref and ground from the ecu, you need to get it form that
@VTECAcademy
@VTECAcademy 2 года назад
If you simply splice the 12V wire in, it will damage the sensor. I believe I covered that.
@tiimarc20
@tiimarc20 3 года назад
Do you have link where you buy your terminal pin ?
@kilianvisscher5716
@kilianvisscher5716 3 года назад
Hi there i have a question i have 01 em2 with a k20 and i cant get my speedo to work Will this work on my car
@Jinx-tw7oj
@Jinx-tw7oj Год назад
If you’re doing this on a vss transmission do you still have to change the signal to css in hondata?
@crx4life495
@crx4life495 3 года назад
@VTECAcademy, Is it the same for Ktuner? I believe I had that issue with the AP1 cluster I had on my CRX. Ended up selling it because of the issue. I asked the question about the VSS wheel being eaten.
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
There is another video on speedometer correction for both th eKTuner and Hondata.
@austin4046
@austin4046 2 года назад
I have a Honda Element harness and ep3 transmission with an accord ecu and ktuner. (eg chassis) How do i get my vss to work?
@Lastsight100
@Lastsight100 Год назад
What size terminal is being used for c101 and B plug? is the same size?
@spencer_g1958
@spencer_g1958 Год назад
Do you have to swap any wires around and the transmission plug side????
@seekerofgrace1247
@seekerofgrace1247 Год назад
Do you guys have the links to buy the pin terminals?
@djsonicc
@djsonicc 11 месяцев назад
So for VSS you'd just use the "Normal speed sensor" option?
@AKYGaming
@AKYGaming Год назад
This works with rsx 02-04 harness on a 05-06 rsx transmission to make my speed work?
@uwkcal
@uwkcal 2 года назад
Thanks for the video sir! I plan on doing a k series swap i wanna figure out how i can make everything easier with a k20z swap!! Any tips to avoid any problems and make everything easier, not having todo crazy things to get the speedo correct? Thanks
@VTECAcademy
@VTECAcademy 2 года назад
Which Z? The 1 or 3? What ECU do you want to run? What transmission?
@uwkcal
@uwkcal 2 года назад
@@VTECAcademy k20z4! The fn2 type R! 07-11 im pretty sure its the same as k20z3! As far as ecu! Any kind of ecu since i havent bought any yet! And transmission is the K20z4 5.063 gearbox transmission! I got a complete swap that i want to drop in a civic ek coupe! I wanna know what to purchase and watch out for before wasting any money! I can also however rebuild the transmission so it will be opened!
@tightcar1065
@tightcar1065 6 месяцев назад
@@uwkcalhi mate I know this is a long shot but did you manage to get the swap done?
@uwkcal
@uwkcal 6 месяцев назад
@@tightcar1065 unfortunately no i did not bro i had everything ready togo to drop in and everything! Check out my youtube channel videos of my civic si em1 i’m also selling the car also i already sold all my other nice cars… but had everything Complete to drop in.. its sad news but I wasn’t able to the swap even though i had thousands and thousands of dollars worth of parts i was gonna restore the entire setup on the civic si em1…. But due to certain circumstances i had to sell everything due to specific reasons sadly, i am possibly moving out of country international or i’m moving down south to florida from the eastcoast so i am not able to have such nice things and a lot of stuff otherwise its very costly and more shit i gotta think about and carry with me 😅😪
@user-og8ur8yw7g
@user-og8ur8yw7g 9 месяцев назад
Would this work for an 04 em2 cluster? I have a k20z1 with matching trans, v2 hondata and it reads the vss in hondata but doesnt read on the cluster
@mariopic
@mariopic 3 года назад
i got an 05 to 06 kpro with jumper on 05 honda element i get vss speed on the hondats when logging but speedo does not move at all now do i need to repin somthing to fix it
@401kid6
@401kid6 Год назад
So at first I wired up my CSS (5V & ground from TPS & signal wire from A18) and whenever I would move like 1mph my Speedo would read 150+ mph. Then I did this in my K swapped CD5, and Hondata is reading my speed and it’s pretty accurate except my Speedo on my dash doesn’t move now. What do I do?
@ivangiron6364
@ivangiron6364 10 месяцев назад
Will i need to do this when running an auto ECU with kpro?
@christian_da_hoy9077
@christian_da_hoy9077 10 месяцев назад
Just finished my k24a2 swap into my rsx type s everything works fine speedo ready properly but it is still throwing a VSS malfunction code and won’t allow my vtec to engage. Any ideas of what is causing this? A connection issue or a physical issue with the actual Speed sensor. I am using the stock 02 rsx type s transmission. Please help vtec academy 😭 I miss vtec.
@johnnystoka6625
@johnnystoka6625 8 месяцев назад
Can this be done with an EP3R using a Type S gearbox with a hall effect sensor .
@antoniorangel2523
@antoniorangel2523 Год назад
is this the same process if you choose to use k tuner ?
@augiegonzales7025
@augiegonzales7025 2 года назад
Will this work with k tuner as well
@anthonylusano6906
@anthonylusano6906 3 года назад
Hey guys - love the technical info! I’ve searched and searched, but is there a way to correct inaccurate speedo reading from vss in k20a2 EK? The speedo correction in parameters doesn’t seem to affect the speedometer reading while driving. It reads too fast ~ about 10mph off at 70mph when actually going 60mph.
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
Did you see our other video how to do a speedo correction? It's in the quick tip playlist.
@cyrillagao5032
@cyrillagao5032 Год назад
Were you angle to fix this?
@corneauscustomshondagarage7460
@corneauscustomshondagarage7460 20 дней назад
So if I do this where I have a k20z3 engine and trans in my dc2 I should be able to plug into my css and it will work?
@yaggs8941
@yaggs8941 Год назад
12v to 5v - where do you recommend getting the 5v power from? Is it safe to just tap into an existing sensor without affecting the readings? What about a 12v to 5v converter box? Worried about frying the css. I have 03 rsx s going with an 09 si trans. Thanks Brian! Great info!
@minineji7050
@minineji7050 Год назад
Where did you end up tapping into for the 5v? My car doesn run when I tap into the map sensor
@yaggs8941
@yaggs8941 Год назад
Not doing the swap until further down the road. I think I remember reading on a comment somewhere that Brian recommended to tap into tps power and ground.
@minineji7050
@minineji7050 Год назад
@@yaggs8941 yeah I ended up buying a voltage step down converter bc on my setup it was just much easier to draw from a 12v and modifying the voltage. But it works great lol no issues since
@angelmercado1171
@angelmercado1171 Год назад
@@minineji7050witch one did you end up getting !
@yaggs8941
@yaggs8941 3 месяца назад
​@@minineji7050 which converter are u using?
@napalm588
@napalm588 3 года назад
Would this be the same for a 2007 Accord transmission? Also, would I need to repin the wires where the sensor plugs into the transmission, If I am using a 2002-2004 k20 type engine harness?
@punkaddic
@punkaddic 3 года назад
Yeah should be the same for accord transmission as it uses a css as well. Yeah you'll have to repin for the css because it needs a different voltage than vss but you can use the same signal wire
@suprdude2
@suprdude2 3 месяца назад
Would a CSS plugged straight into a VSS harness prevent Vtec from engaging?
@spencer_g1958
@spencer_g1958 Год назад
So after doing this why do you need the sensor if the ecu is outputting the signal. The signal wire going to the vss isn't there any more??
@lazya666
@lazya666 Год назад
where are the links to buy the connectors??
@5Seenitall
@5Seenitall Год назад
Hi Can You Post Link To Where to Get Connectors?
@dustinwickham4669
@dustinwickham4669 2 года назад
If you have a vss harness and a css trans and I change the plug on the trans side would the wiring be the same for each plug or would the pins need to be moved around?
@VTECAcademy
@VTECAcademy 2 года назад
If you use the VSS wires, you will burn up the CSS. The VSS uses 12V and the CSS uses 5V. You need to use the 5V signal and sensor ground wires from the TPS (wired in parallel) with the Signal wire from A18 on the ECU.
@benjamieson5626
@benjamieson5626 3 года назад
Can I do the same thing with my k24z7 swap? Have it running off the stock 2012 si computer and fuse box. Got the tach wired but haven’t sorted out the Speedo yet.
@VTECAcademy
@VTECAcademy 2 года назад
No, you will need to use a speedometer signal converter like the one sold by Dakota Digital or Healtech.
@gandstactical
@gandstactical 2 года назад
I have a Ep3 harness on a K20z4 tranny. Would this work on my setup as I have kpro v4? I've dropped the motor in to the es2 (similar to Em2) with a ktuned conversion harness?
@VTECAcademy
@VTECAcademy 2 года назад
Yes it would.
@brettcarcio4013
@brettcarcio4013 3 года назад
Does the CSS sensor output go to the vss pin on the ecu or the vss wire on the kpro v4 board?
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
Yes VSS pin A18
@jeremyjames2606
@jeremyjames2606 4 месяца назад
Man bout to give up on the speedo. Followed instructions on video to depin 101 and add wire from b11 to c101. Also have rewired css sensor from 12v to 5v from map power and wired ground to signal ground on map sensor. Kpro is switched to css still no movement. 06 K24a2, 02 ep3 factory harness, 05 rsx base trans in 99 civic hatch. What am I doing wrong?
@TreadShredders
@TreadShredders 2 года назад
Awd ep3 here. I understand the wiring on the inside, as explained in this video. On the transmission plug side, I need to shave the plug to fit and cut the middle wire at the plug and run it to the MAP sensor for 5v power? Leaving the wire from the harness taped back into the harness
@VTECAcademy
@VTECAcademy 2 года назад
If you are going from the stock VSS to the Element's AWD transmission CSS, then you need to replace the plug. The only wire you will reuse is the signal wire. The other two wires, 5V power and logic ground, come from tapping into the MAP sensor.
@TreadShredders
@TreadShredders 2 года назад
@@VTECAcademy Thank you! I'm going to give this a shot today and see how it works out. Much appreciated.
@TreadShredders
@TreadShredders 2 года назад
Finally got around to getting it wired up. I wired the CSS plug as follows to no avail. Signal on plug to vss signal wire. Left the other two wires at the plug taped up. Wired the CSS 5v and ground to the map sensors 5v and ground. Changed to CSS in Kpro and have no luck. Any ideas what I'm doing wrong? Thanks again for your time.
@VTECAcademy
@VTECAcademy 2 года назад
@@TreadShredders Did you try running the CSS with the 12v first? That will kill it. Recheck the position of the wires. The information for the position is holding the plug with the clip up with the wires facing you.
@TreadShredders
@TreadShredders 2 года назад
I didn't. I'll check the wires when I get home. I also used a spacer for the sensor as I screwed it in, it would make contact with the gear and the trans wouldn't move. Maybe it's too far away now. I'll check wires and sensor position
@ninodass6951
@ninodass6951 2 года назад
Sir you know how am getting diagram of green wire back of honda civic 2002 speedometer
@Brian-qe5rl
@Brian-qe5rl 3 года назад
Any help here my VSS shows on KPRO just not my cluster
@CASCARITADC2
@CASCARITADC2 2 года назад
Hey Brian! I'm using a 2005 Accord 5-speed transmission with 2002 Rsx Base auto ECU on my 1999 K-swaped Integra. I know I have to de-pin A18 and wire it to the hondata board (red wire). Will this work with my setup or do I have to buy a VSS converter? My speed reach 158 mph as soon as I start driving. Thanks!
@VTECAcademy
@VTECAcademy 2 года назад
It should work on your car. Honestly, I need to do a video on using the Hondata board to do the conversion too.
@ivangiron6364
@ivangiron6364 10 месяцев назад
Did it end up working? What did you do?
@xiaher1328
@xiaher1328 2 года назад
Does this fixed the check engine
@k20CRX1
@k20CRX1 2 года назад
Do you have a link to where I can buy that terminal pin set? I don’t see anything in the show notes.
@vizcarraawd
@vizcarraawd 2 года назад
This question hasn’t been answered like 4 times.
@reefgameaquatics9285
@reefgameaquatics9285 3 года назад
I’m going to try this because I have the same problem.. the rpm works so does the gas gauge ... the mph don’t work .... also I have a quick question if I plug in my transmission plug I can’t use reverse I have to leave it unplugged... can that be the reason I don’t have the mph working?
@VTECAcademy
@VTECAcademy 2 года назад
It's possible. If your ECU is set up to show a constant speed it may be activating the reverse lockout.
@Serpentis666
@Serpentis666 3 года назад
So in this case, after depinning the wire from the c101 plug, would I still be able to just wire b11 to the orange wire at b10?!? I did this as per your last instructions, sans the depinning of the c101 plug wire and my speedo “worked” but it just pinned as soon as I rolled the tires and then when I slow down again to a near stop it goes backwards again...
@VTECAcademy
@VTECAcademy 2 года назад
You are giving the speedo the CSS signal which is many times faster than the VSS signal. You need to adjust the percentage output of the speedo to reduce the signal speed. Try starting with 10% and see where that gets you.
@jdmlyfestyle710
@jdmlyfestyle710 2 года назад
Did you end up depinning c101 and splicing in b10 abstrahere or did u just pin into b11
@VTECAcademy
@VTECAcademy 2 года назад
@@jdmlyfestyle710 I de-pinned it at the C101 and added a wire from B11 to the C101.
@macklin9708
@macklin9708 3 года назад
Hey brian thnx for the knowledge. I’m running a k20z3 with k20a2 harness. I tried this and can’t get my Speedo to work still. I’m using a rsx speedometer
@VTECAcademy
@VTECAcademy 3 года назад
What year RSX?
@macklin9708
@macklin9708 3 года назад
@@VTECAcademy 02-04 harness and rsx cluster- 07 k20z3
@macklin9708
@macklin9708 3 года назад
It’s in a mr2. Also I have the vss wire from the rsx cluster going to the E plug pin 25-vss out. Not sure if that’s correct
@macklin9708
@macklin9708 3 года назад
Any tips if I’m missing anything?
@macklin9708
@macklin9708 3 года назад
@@VTECAcademy any tips?
@Tyler-jt1tl
@Tyler-jt1tl 9 месяцев назад
I just did this on my integra with a z3 trans and now my speedo is reading nothing. Any suggestions?
@captain_grubby9734
@captain_grubby9734 2 года назад
I recently did this to my k24a2 with a type s rsx harness from an 02 and it doesn't read the speed at all. When I went into Kmanager I switched from the recommended choice which is css driven to the non vss option and it pegs the speedometer at 50mph. When I go and switch it back to css speed sensor on k manager it doesn't read neither on the ecu or the cluster and it doesn't throw a code.
@VTECAcademy
@VTECAcademy 2 года назад
It sounds like the sensor is bad, or not powered. Did you wire the CSS with the 5 volt MAP voltage or the 12 volt VSS voltage?
@Boostlee2023
@Boostlee2023 Год назад
@@VTECAcademy so just swapping the 3 wires around on the 02-04 rsx harness I have to the 03-07 accord transmission css plug like my harness says won’t work?
@uptownx24x
@uptownx24x 3 года назад
I had the issue with my k swap in my EK with the s2000 cluster and could never figure it out. Ended up selling due to the fact.... Wish I would have known
@crx4life495
@crx4life495 3 года назад
Same here, I sold my AP1 swap because it never worked properly.
@aliniksejel8683
@aliniksejel8683 Месяц назад
Question. So I have a KSWAP in my type r and going 80mph it reads 90mph. How do I fix that?
@EricDolinar
@EricDolinar 2 года назад
So I have a k20z1 engine and trans out of an 05 type s. I am planning to use a 02-04 harness with 02-04 k pro. Will this work with the 02-04 kpro V4?
@VTECAcademy
@VTECAcademy 2 года назад
If the V4 was installed by Hondata.
@EricDolinar
@EricDolinar 2 года назад
@@VTECAcademy bummer. I wonder what’s different between Hondata installing it, and any of the other installers?
@daylindrake768
@daylindrake768 Год назад
Question is the 96-2000 speedo pcb the same as the crv i swapped the gauge face to my 96 board and put it in the crv cluster when i plug it all in with the lens off to calibrate speedo needle it reads 0 but pass radar says im 15 under thanks
@VTECAcademy
@VTECAcademy Год назад
Not sure. I've seen people calibrate the speedo by repositioning the needle, but If the. tire size is off, I'm not sure that works.
@dustinlewis47
@dustinlewis47 Год назад
I know this is years later but im running a 03 accord apg6 honda accord transmission with a rsx type s harness on kpro on my 95 coupe will i have to modify my harness for my speedo to work?
@VTECAcademy
@VTECAcademy Год назад
Yes you will.
@kyranwoodbury5300
@kyranwoodbury5300 Год назад
I'm running a css speed sensor on my gearbox and using a rsx 02-04 engine harness with a kpro v4 ecu. I'm not sure if I missed anything, but if i follow this video and change those wires from the c101 plug and linked it to the b plug as followed. do I have to alter the rsx plug wires to suit the css senor???? sounds like me finding this vedio may have saved my life
@VTECAcademy
@VTECAcademy Год назад
Dont run the CSS on the 12 volts from the VSS.
@kyranwoodbury5300
@kyranwoodbury5300 Год назад
So what would you recommend?
@Boostlee2023
@Boostlee2023 Год назад
@@VTECAcademy so what do you do if you have a nice harness and don’t want to butcher it all up?
@logitikes
@logitikes 3 года назад
How does this work? If you disconnect the wire going to the ecu from the vss and A plug, how does the ecu get a signal from the vss?
@punkaddic
@punkaddic 3 года назад
Maybe you haven't realize that both css and vss are speed sensors but in different location. CSS now gives that info to the ecu
@CaliHondaChannel
@CaliHondaChannel 11 месяцев назад
Hows it going everyone new here to the community 🙏 I have a 02-04 jdm crv k24a in my ep3 with my stock ep3 transmission. Running on kpro v4. But my vss sensor is on. Car runs strong, I had it tuned recently but i was wondering what has to be done to make the vss sensor go away, since it wont let my 2 step engage Do I have to repin my vss pig tail plug? Or bypass I'm running the ep3 harness Car runs amazing though Thanks yall
@VTECAcademy
@VTECAcademy 11 месяцев назад
If your speedometer works correctly, then that's not the problem.
@brahimalnaqbi419
@brahimalnaqbi419 3 года назад
Hi. I'm dr. Honda from Dubai ... I have a RSX S and a Haltech car computer. When air condition programming worked it does not work. The revers solenoid does not work. What is the solution
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
Wow. You'll need to talk to Haltech about that. I haven't used that yet.
@joexiong13
@joexiong13 Год назад
I know this video is old, but will this also work for swapping complete 02-04 JDM K20R into 05-06 RSX type S? We’re having trouble with getting the vehicle running. It’s almost in limp mode due to the Speedo not working properly. Thanks.
@VTECAcademy
@VTECAcademy Год назад
Do you have a Hondata ECU that Hondata did the install on? Then yes.
@A.QPerformance
@A.QPerformance Год назад
Basically 05-05 onward its CSS high frequecny signal your ecu is looking but that JDM tranny has VSS which operates on 12v and outputs a low frequency signal. So need to convert that low to high frequency using a converted like Dakota. But you can get car out of limp mode. There is an option in Flashpro about percentage adjustment to dash and ecu. just put 5000% there and the VTEC etc will work but speedo will still show very little speed. You will need a converted to get that speedo work.
@joexiong13
@joexiong13 Год назад
@@A.QPerformance it’s on a k pro V4. Would that have the option also? Sorry, I haven’t messed with Hondas in such a long time and also not familiar with the RSX chassis.
@Brian-qe5rl
@Brian-qe5rl 3 года назад
Hey Brian I got this wired up. However the Speedo doesn’t work on my cluster, it is showing on KPRO. Could it be that my ecu wasn’t installed by hondata?
@VTECAcademy
@VTECAcademy 3 года назад
Probably. I need to visit Hondata and see what modification is done so I can let everyone know.
@Jose-gc2xk
@Jose-gc2xk 2 года назад
@@VTECAcademy yes i need this asap. I wired the c101 to b11 but nothing happened 😔
@tomydespins2315
@tomydespins2315 2 года назад
So this speedo correct work with vss and css ?? Cause I have a kprov4 install by a approve installing tuning shop I use vss and my cluster is off of some kmh(in Canada) I need to roll at 140kmh on the cluster to actually roll 120 on the GPS I made my mind around it but it begins to annoy me
@VTECAcademy
@VTECAcademy 2 года назад
I don't know what your setup is. Can you tell me what transmission you are using in what car?
@tomydespins2315
@tomydespins2315 2 года назад
@@VTECAcademy i have an 99 EM1 k24a RBB jdm Engine swap with a EP3 type r transmission
@VTECAcademy
@VTECAcademy 2 года назад
@@tomydespins2315 I don't know if the shop you used set the right jumper to output a speed signal. My understanding is only Hondata does it. But if you hook up B11 to your speedo and get a signal, then the company that installed the KPro did a good job and you can adjust the percentage in the Hondata software to get an accurate reading. And to answer the original question, the adjustment works with VSS or CSS.
@guiaudet3694
@guiaudet3694 8 месяцев назад
Hey vtec academie , i did this with my friend v4 , and it work very well , i switch the ecu with mine (v4 too) and it didnt work , i lost speedo , try to replace the wire like it was before , my speedo came back but the speed was not accurate, im lost
@VTECAcademy
@VTECAcademy 8 месяцев назад
There may be a percentage of value written in for the speedometer output.
@bossdogg669
@bossdogg669 3 года назад
Hi there where can I buy the crimping tool for the AB&E plug
@VTECAcademy
@VTECAcademy 2 года назад
Check out the K-swap wiring video here - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-weeuPKHrbPo.html
@somuchjuice5528
@somuchjuice5528 3 года назад
Does this apply to a 05-06 type s harness also?
@VTECAcademy
@VTECAcademy 2 года назад
Yes
@BongoBennieTV
@BongoBennieTV 3 года назад
Will this work if you want to alter the Speedo of a VSS vehicle instead of CSS?
@VTECAcademy
@VTECAcademy 2 года назад
Yes.
@user-wr5qb5od6w
@user-wr5qb5od6w 8 месяцев назад
Tried on my v4 Kpro and it read speed on data logging but cluster output not working, Help
@cheemongyang1090
@cheemongyang1090 2 года назад
Just to clarify if i do this step here that means that i dont need to buy a speed converter? Also will i still need to plug the harness onto the vss sensor on the transmission?
@DeesmanONE
@DeesmanONE Год назад
You do still need the converter
@cheemongyang1090
@cheemongyang1090 Год назад
@@DeesmanONE ok thanks
@ohxietviet
@ohxietviet 2 месяца назад
@@DeesmanONEwhat? If you have kpro v4 you don’t need a converter.
@BrandonMeidinger
@BrandonMeidinger Год назад
@vtec academy so how do I make a k20z3 trans work with a 2000 civic si dash?
@VTECAcademy
@VTECAcademy Год назад
Run a speedometer conversion module like the one from Dakota Digital. Use the NEP on the E Plug to drive the tachometer. Add a the EM1 single wire temperature sensor to fee that info to the dash.
@kerthao470
@kerthao470 10 месяцев назад
Hi I have a k20z3 in 97 acura integra trying to get speedo to work can you help thanks
@VTECAcademy
@VTECAcademy 10 месяцев назад
Email vtec.academy(a)gmail.com with your question. Include your setup info. ECU, transmission, etc.
@Thoroughbredable
@Thoroughbredable 2 года назад
I did turbo conversion on my K20Z4, speedo goes to zero and power steering stops working...is this the solution?
@VTECAcademy
@VTECAcademy 2 года назад
Was it working before you turboed it?
@yaggs8941
@yaggs8941 3 месяца назад
Anyone using tps wires for power/ground on css? Any problems with tps afterwards?
@throttleproneandoregongrow5703
@throttleproneandoregongrow5703 2 месяца назад
I tried to do this I’ve watched the episode many times and i still can’t get it to work helpppp!
@landoski
@landoski 3 года назад
Will this work for an auto rsx engine harness?
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
Yes
@nof9741
@nof9741 3 года назад
Any conversion needed for base rsx harness to work with k24a3 rbb ecu?
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
Yes depending on the harness. There are some differences in auto and manual as well as differences between 02-04 and 05-06.
@nof9741
@nof9741 3 года назад
@@BrianGillespie_brianathasport any links to a k24a3 rbb ecu pin diagram? The k24a3 runs with my base k20 ecu but doesn't run with its own ecu. I'm using the base rsx harness
@nof9741
@nof9741 3 года назад
Both harness and engine are between 02-04
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
@@nof9741 No links to the Accord specifically, but if you wire it the same as the 05-06 RSX it should run with the RBB ECU.
@mannyactual
@mannyactual Год назад
Does this apply if you are running ktuner ECU?
@VTECAcademy
@VTECAcademy Год назад
Mostly. Look at our Budget EG video on that.
@AKYGaming
@AKYGaming Год назад
How does my speed gauge get signal if its not plugged lol since your not using that new wire to go to the cluster
@VTECAcademy
@VTECAcademy Год назад
From the ECU?
@mx3autozam
@mx3autozam 3 года назад
How would I tell if my kpro was installed by hondata?! Is it just hondata that sets them up for VSS output
@chelek20godoy93
@chelek20godoy93 3 года назад
I ask myself the same question, for me I have to configure something else in the hondata
@EvilBtT
@EvilBtT 3 года назад
@@chelek20godoy93 Did you get this to work?
@MetalGear_Markie
@MetalGear_Markie Год назад
What are people doing with kpro that wasnt socketed by Hondata? I have a hamotorsports v4 ecu and want to do this in my k24 swapped integra
@VTECAcademy
@VTECAcademy Год назад
I need to research how to convert the ECUs and share it. Otherwise some sort of speedometer interface like the ones from speedohealer or Dakota Digital.
@MetalGear_Markie
@MetalGear_Markie Год назад
@@VTECAcademy for right now would you suggest I get the k tuned conversion box? I used the Dakota box before on my rsx and I didn’t like it
@proofturgeon
@proofturgeon 2 года назад
Where do u wire the signal wire from the css pig tail ?
@VTECAcademy
@VTECAcademy 2 года назад
Depending on the year, it is usually the grn/wht or blu/wht wire.
@EvilBtT
@EvilBtT 3 года назад
So this only works it's installed by Hondata?
@TwisNinja
@TwisNinja Год назад
i dont see the difference from hondata doing the install vs. a dealer ALL components in the kit are used so why does only a hondata installed ecu do this please explain technically or its not true if you cannot
@danjko888
@danjko888 10 месяцев назад
Hey Brian, can you sell me a jumper wire from the b11 to c101? Im not sure about other people, but I dont really want to buy a kit for just 1 wire. Thanks
@VTECAcademy
@VTECAcademy 10 месяцев назад
I need to find an employee I can pass all those types of projects off to.
@joshcapo3745
@joshcapo3745 3 года назад
is it possible to use a k20z1 engine harness for a k swap with a hondata with z1 trans
@bestmastermind951
@bestmastermind951 3 года назад
It is possible u will need to convert the harness to run hondata tho or u can run k tuner but I'm this vid he shows u how to make the spedo work of u are using a trans with speed sensor in front u just gotta one wire shown in this vid from ur harness I'm doin the same as you
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 3 года назад
Yes. You will need to make some changes to the harness though. The A, B and E plugs are pinned slightly different. That needs to be another video.
@EricDolinar
@EricDolinar 2 года назад
@@BrianGillespie_brianathasport have you done a video on that yet?
@BrianGillespie_brianathasport
@BrianGillespie_brianathasport 2 года назад
@@EricDolinar Not yet
@itsfred91
@itsfred91 Год назад
@@BrianGillespie_brianathasport how would I be able to use a 02-04 kpro on my dc5 I’m fully built k20z1. I know I’d need a jumper harness from hondata but why else would I need to send my ecu to them is it because of the vss? And that only?
@tymege6230
@tymege6230 2 года назад
Does this work with k20z1 with 05-06 harness on a 02-04 kpro v4
@VTECAcademy
@VTECAcademy 2 года назад
Yes.
@tymege6230
@tymege6230 2 года назад
@@VTECAcademy so I have the jumper harness instead of repin My e plug goes to b11 on the ecu do I also have to get power/ground for the css from the map or should it already be there
@WesamSaleem1993
@WesamSaleem1993 Год назад
I'm running a 6 speed tsx transmission with a 2004 PPA CRV manual harness I've reppined the VSS sensor to suit TSX type on engine harness also fitted correct connector to suit I'm also running a kpro v4 will this work with my 2004 PPA engine harness ?
@VTECAcademy
@VTECAcademy Год назад
Yes it will if wired correctly.
@eddiehp6108
@eddiehp6108 Год назад
Wonder if my aem v2 can do this
@VTECAcademy
@VTECAcademy Год назад
Mine doesn't, but it is about 14 years old. They may have made changes.
@d.i.mdoitmyselfgarage8874
@d.i.mdoitmyselfgarage8874 Год назад
Do we have to repin the connector to the sensor?
@VTECAcademy
@VTECAcademy Год назад
Each sensor has its own required connector. If you change from one to the other you need to change the connector.
@d.i.mdoitmyselfgarage8874
@d.i.mdoitmyselfgarage8874 Год назад
@@VTECAcademy im using the 05 accord sensor and connector. Got it to read by pek out the gauge going 3 mph. Im also using 5v from the map sensor. Any idea? Thanks 🙏
@bobericatabelo3052
@bobericatabelo3052 3 года назад
I have done this but my speedometer is not moving
@jeffberg5196
@jeffberg5196 3 года назад
Does this only work on the v4?
@VTECAcademy
@VTECAcademy 3 года назад
Yes, it seems so.
Далее
Budget EG K Swap Power Mods with DYNO
18:21
Просмотров 72 тыс.
Ummmm We "HAIR" You!
00:59
Просмотров 2,4 млн
POV: Spain vs Italia
00:11
Просмотров 348 тыс.
Custom K Swap Universal Adapter Harness
50:48
Просмотров 11 тыс.
Reverse Lock Out Quick Tip
5:43
Просмотров 15 тыс.
How to test Vehicle Speed Sensor
3:07
Просмотров 162 тыс.
Когда купил машину 300+ л/с 🤔😂
0:59
Дорох и алкобайк
0:55
Просмотров 1,8 млн
МОЯ НОВАЯ МАШИНА🤩😍 MERCEDES?😱
0:59