How To - 3 ways to add nocking points - (Pros & Cons of each) 

Finaly somebody knows how to nock a arrow! Thanks for telling everybody.

One tip on installing the brass nocking point is to not install it tightly in the beginning. You can then spin the brass nocking point, one way or the other, to move it up or down the string while you are bare shaft tuning to get the proper nock set height. Spinning the brass nocking point will move it up or down the serving due the angled wrap of the serving. Like you said, installing it 1/4 of an inch high is a good starting point.

I'm a pretty big fan of serving. Do it right and it's adjustable by twisting it up or down

I am here in Regional Australia and have used fishing braid

Thank you for this video. After shooting for 4 decades, I learned something new and practical.

I like the serving but I hadn't seen it done that way. That's sharp. Thanks for the video!

What a fantastic way of doing a serving thread nock, so simple, elegant, and beautiful. Thank you for sharing your wonderful method. Extra bonus points for mentioning how to easily remove brass nocks.

Learning to tie fishing knots, this seems easy.

Awesome 👍🏻 thank you very much for explaining this in a common sense way... Every video brakes it down and makes it thoroughly understandable, informative and enjoyable. Kudos to y'all!!!

I use the knotless nocks for temporary nocking points. If you tie them right going with the twists of the serving and being careful how you burnish, you can twist them up and down to adjust the height while tuning. Once I've got the right height I cut them off and them do a Korean nocking point with serving which are very similar to the knotless ones but they are quite a bit lot longer and they last forever. They are more complicated again. These are popular nocking points for Olympic recurve style archers. Ashe Morgan from the Online Archery Academy channel has a excellent tutorial about how to tie them.

For my nail knot nocks I use a knitting needle. I have a 3.25 mm but that is just what I have on hand (they also work for pulling broken nocks out of arrows). I wrap towards the hook and then use the hook to pull back through the loops. This works for me because I make ~20 wraps for a nock point that is longer and not a pressure point on my finger. Works great getting that end through all those loops.

Your videos are concise, clear, and always interesting! I've used all three and use floss for finding the best point and the serving nail knot for the perminant nocking point. All the best with your new bow line!

Your tips are just so great. I'm excited. I like to improvise in my life and of course also when it comes to archery. I like the serving line method best. I have the material here anyway, I can change it quickly at any time and it's hardly bulky. For me the ideal solution.

Might be a dumb suggestion but I wouldn't have minded watching you take the nail knot off. Is it still easy to cut with a razor blade?

Very helpful! Thanks!

I just ordered a traditional bow with no arrow shelf, so where would i position the knocking point?

You can also use any thick thread for sewing

Funny thing, Shatterproof just shipped my new bowstringa and YT sent me this link. Maybe YT was spying on me 😆 I use the brass knuckles or flossing more so the latter since it's easier for me to reposition my nock as I tune up a new bow. Once I get my bow and shaft at a spot that I want to be at, I cut the floss and crimp on a brass at the same spot. I shows split for

Interesting stuff! 😊

Wow, never thought that you can use tape for temporary nock!

Great!

I use dental floss dead easy to tie on. I find it more convenient than those brass things.

Would a strand of bow string work as well?

Have a question for you can you use the over hand knot system also with the serving material ?

Love these how to videos! Newbie question. With a single nocking point on the bow string, where is the customary placement of the arrow nock....Above or below the nocking point?

I don't have serving. Would heavyweight thread such as carpet thread work? Thanks. TomlovesDIY

I have also found that using a double constrictor knot with serving material works great.

It is a knot adopted from flyfishing. You can tie without a pen and then it is called a nailless nail knot. I believe you are incorrect in your definition. Ask me how I know?

Brass works great for American recurves. But if you shoot Asiatic recurves/horse bows then really serving is the only way.

There is a third method that is more expensive, I have seen people use the rubber nocks called Nitro Speed Nocks but mainly adults/teens using it on lever bows or glove/tab style compounds like the Gen--X, or the right hand only Bernet kids--small adult 27 inch draw 20--45 pound bow the Vortex/H20 eior this one model SAS/Junxing sell that is a 1994--1995 style of bow in a more generic look as these people need something for a bow that is going to hold better then these 3 methods that will wear out sooner. I have seen the floss replaced by using thread mainly on RU-vid but a few times in real life once with a Leverbow used more like a traditional bow without a sight and fingers so they could use a color that stands out well but less likely to get dirty like the floss due to the slightly sticky nature of the material. One guy said in his youth in the late 1960's and into the 1970's they used a small piece of baling wire as the nock and shot with an older style single hole style tab made from old worn out palm side thinner leather work gloves using back part they cut out themselves as that leather was still good on those worn out gloves on the back. They did this so they could afford to use the better broadheads from Bear, the single bevel models no longer made with the fiberglass arrows of the era for better durability then wood but cheaper then Aluminum that was more expensive then fiberglass.