HOW TO ADJUST CHAIN SLACK ON A MOTORCYCLE? DOMINAR 400 CHAIN ADJUSTMENT FIXING LOOSE CHAIN FOR NOISE 

I need that video's link bro pls 😀 I also have 160 4v

Thanks a lot for appreciating the efforts; really means a lot to me 😊

Thanks a lot for appreciating the efforts ❤️

Thank you so much for appreciating the efforts, really means a lot to me 😊 Have you checked these: 1. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Zfrqgch59M8.html 2. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Uc8qKzecYRA.html

Thank you so much 😊

Thanks a lot Zeeshan for the wonderful words of motivation.. Definitely more videos on RTR 👍

Hi! First you can begin by roughly selecting a center point in between the front and rear sprocket like shown in the video, from there try to force the chain down and up (vertically), the total distance from bottom point to top point is your chain slack. Thanks a lot for valuing and appreciating the content on the channel, really means a lot to me 😊 I have explained something similar but in more detail over here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Zfrqgch59M8.html

Hi Bosco! You have to measure it from top most position to bottom most position; also make sure the slag is measured roughly at the center between the two sprocket with wheels touching the ground.

@@thesportztourer thank you I'll surely try that I'm also from pune please check you Instagram I have messaged you if possible we can meet up

There are torque recommendations in the bike’s owner’s manual for such bolts. It basically tells you how tight it should be for optimum performance of that nut. If you tighten it more it may cause issues, if you tighten it less it may come out due to vibration. There a tool called torque wrench which is used where you can set the tightness number ( torque value given in manual) in the tool and then tighten it. It stops at that value and will indicate that the tightness has reached the value required. Torque wrenches are a bit expensive though.

Hi! Well explained by @prithvinayak The channel has also got video on torque adapter/wrench: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MZekoIwtPtE.html

Hi Naveen, Diesel works fine for me. My RTR 180 did 50k km with diesel cleaning 😊

Will try to, need to get that special tool for adjustment 😊

@@thesportztourer Sure.. thank you! 😁

Yes, faced similar issues and finally the chain was replaced a few months back. The new stock chain sprocket is of better quality as no frequent adjustment was required after replacement. Have you checked this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-o1RXP3UQ4Pw.html

Hi, From the chain?

@@thesportztourer yes..like hitting something

Hi! This seems to be a problem with alignment (check the marked indicators on both sides of the rear axle). Other things to look for is wear and tear on a particular sprocket teeth and frozen chain links.

The Sportztourer Yep already check both are in same position. Any other solution please

Same condition on my RTR 200 If you got solutions pls reply

Need to check on that, the carb tuning has major role it that (plus the air flow).

@@thesportztourer i have just changed the air filter but my carb is at lean mixture should i change it ...?

Hi Akshay, Metal to metal contact will make some noise still if you feel it's abnormal get it inspected from the showroom. This video should help: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7tWrylPGvE0.html

Yes i have also seen it & asked them they replied It is mentioned in there TVS service center Manual edition 2018.

Hi Suraj & Ameya, That can be done but the required slack will be different from the standard slack plus the weight on the motorcycle is not specific to the rider. It's different but not a wrong practice 😊

@@thesportztourer i agree👍

My chains are run only 4000 km

Hi Raghul, A lot of reasons can be behind that, you can ask the service guys to specially pay attention to it. If you have not seen this before then this video should be helpful: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7tWrylPGvE0.html

For every service that is once in 4 to 5 months and around 4500 km I ask service center to do chain adjustment

Hi Biswajit, Have made a detailed video on flush here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MZnnHCDq8uU.html Do you want a specific one for 3M?

Hi Sourabh, I doubt it will fit still things need to get checked for that 😊

@@thesportztourer 😅