How to Assemble and Setup AC Manifold Gauges - HVAC

Подписаться 17 тыс.

Просмотров 32 тыс.

50% 1

[AC Manifold Gauges] - Both work great!
AURELIO TECH 3 Way A/C Diagnostic Manifold Gauge Set, Fits R134A R12 R22 and R502 Refrigerants, with 5FT Hose, Acme Tank Adapters, Adjustable Couplers and Can Tap: amzn.to/3xQLwHi
Lichamp AC Manifold Gauge Set with Self Sealing Can Tap, All-in-One AC Gauge Set for R134 R12 R22 R502 Refrigerants: amzn.to/3wEbH2D
[Refrigerant]
R134a Refrigerant 12oz Can - Pack of 1 (PLAIN - GOOD!): amzn.to/39FwtJS
R134a Refrigerant 12oz Can - Pack of 3 (PLAIN - GOOD!): amzn.to/3bfBol2
R134a Refrigerant 12oz Can - Pack of 6 (PLAIN - GOOD!): amzn.to/3wxSHmw
R134a - Johnsen's 6313 R134a Refrigerant 12oz, Pack of 3 (with UV Dye - GOOD!): amzn.to/3hCGtF5
Sorry no links for r1234yf
R12 is now banned for sale. No links.
[Refrigerant Dispenser]
R134A Can Tap Refrigerant Dispenser with Tank Adapter, 1/4" SAE Female to 1/2" ACME Tap: amzn.to/3b9yOgx
[AC Vacuum Pump - For Pulling a Vacuum]
Vacuum Pump 3 CFM 1/4HP Air Conditioner Refrigerant HVAC (CHEAP!): amzn.to/3yRAuBZ
Vacuum Pump 5 CFM 1/2HP Air Conditioner Refrigerant HVAC (CHEAP!): amzn.to/36yvSEz
[For AC Leak Detection]
UV DYE ONLY - InterDynamics Certified AC Pro Car Air Conditioner Leak Detector Dye: amzn.to/3km0QrT
UV FLASHLIGHT ONLY - amzn.to/3y8cUn5
UV FLASHLIGHT + UV ENHANCING GLASSES - amzn.to/3BIPa8R
Refrigerant Leak Detector - Very Cheap (Works for: R22 R410A R134A R1234YF): amzn.to/3l1YjDj
Refrigerant Leak Detector - Good Quality: amzn.to/3zG4FML
[Crocodile Clips - For Jumping the Clutch Relay]
10 Pieces and 5 Colors Test Lead Set & Alligator Clips, 20.5 inches: amzn.to/3efS4rq
[AC Pro - No Manifold Guages Required to Re-Fill]
AC Pro Car Air Conditioner Synthetic R134A Refrigerant, AC Recharge Kit with Hose and Gauge, 20 Oz, ACP200-6: amzn.to/3wGW3DE
[Digital Scale - For Weighing Refrigerant]
Digital Scale (Cheap!): amzn.to/3y8Is9D
[PAG Oil - For AC Compressors/Systems Requiring PAG Oil]
PAG Oil (WITH UV Dye): amzn.to/3OL6NdV
PAG Oil (Plain): amzn.to/3OrZ5F5
[Misc Tools]
U-Joint Set: 1/4", 3/8" and 1/2" Drive: amzn.to/3ambTvs
9pc Socket Extension Set: 1/4", 3/8" and 1/2" Drive: amzn.to/3pnvQGz
Metric Wrench Set 8mm - 22mm: amzn.to/2xQn3ot
Socket Set 123pc Metric and Imperial - Good Quality: amzn.to/2NhqhL9
Socket Set Metric/SAE 23pc - Good Quality: amzn.to/3OuUHVS
--------------
[CHECK OUT MY OTHER AC VIDEOS]
How to Pull a Vacuum and Recharge Your AC System - ULTIMATE GUIDE - HVAC
• How to Pull a Vacuum a...
How to Find AC Refrigerant Leaks in Your Car (UV Dye) - HVAC
• How to Find AC Refrige...
How to Assemble and Setup AC Manifold Gauges - HVAC
• How to Assemble and Se...
How To Jump Start an AC Compressor Clutch + Cooling Fans - Jump Relay
• How To Jump Start an A...
AC Performance Test - Simple and Easy - No Tools Required!
• AC Performance Test - ...
Scroll Valve Replacement - WARM AC AT IDLE & COLD AC AT SPEED - FIX!
• Scroll Valve Replaceme...
--------------
Instagram: / tutorialgenius
--------------
BECOME A MEMBER OF OUR CHANNEL!
If you become a member of our channel, you get various cool and unique benefits!
Benefits:
- Early access to new videos
- A personalized shoutout in each new video during your membership
- Priority responses to your videos comments
- Access to a cool and unique emoji set
Join here: / @tutorialgenius
--------------
How to Assemble and Setup AC Manifold Gauges - HVAC
The car in the video is a SATURN VUE 2007 AWD (04-07 for SATURN VUE 3.5L V6 SOHC 24V VIN CODE "4" J35 / L66). However, the procedures shown in the video will apply to most vehicles and applications.
SUBSCRIBE FOR MORE!
#ManifoldGauges #AC #HVAC
Video Title: How to Assemble and Setup AC Manifold Gauges - HVAC
Video File Created Date: Monday, 20 June, 2022 (Video may or may not have been captured on this date, it shows the date the video was last converted.)
-- Video uploaded and managed using RU-vid Bulk Uploader for the Lazy!
-- Manage and Auto-Tag your RU-vid videos offline... Then upload!
-- ginkosolutions.com/youtube-bul...
-- GinkoSolutions.com
Video Tags:
how, to, assemble, and, setup, ac, manifold, gauges, hvac, r134a, refrigerant, ac manifold gauges, recharge ac system, refrigerant charging procedure, ac manifold gauges harbor freight, ac manifold gauges readings, ac manifold gauges set, ac manifold gauges how to use, ac manifold gauges explained, how to use a/c manifold gauges, how to set up ac manifold gauges, purge ac manifold gauges, how ac manifold gauges work

Авто/Мото

Опубликовано:

1 июл 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 44

@TutorialGenius 2 года назад

Like and subscribe for more! All parts, tools and more information in the video description. If this video helped you, please support the channel by clicking "Thanks"! We also have memberships to our channel with great perks! ru-vid.com/show-UC0HkS2-1Tk1ULQJj3uGbjdwjoin Thanks for watching!

@robmunger922 Год назад

Great video I’m new to using these gauges and I wasn’t totally sure how to assemble them. So I thank you for taking the time to help me.

@TutorialGenius Год назад

Glad it was helpful! You're welcome! :)

@checkoutjason 11 месяцев назад

Thanks for this video and the other one on vacuuming your system. I just wanted to point out i had an issue where the yellow hose was connected backwards (one side had a rubber seal the other did not) I didnt notice at the time and when i was installing freon it leaked badly...Just wanted to point this out for other people so you dont make the same mistake as me.

@olenaerhardt7725 Год назад

Thank you for a great film. I have the set similar to the one fm/the film, but never used it yet. And if I just want to check if any freon is left, should I still run the car, or I can just connect the hoses (I think yellow hose should go into the 2nd for it hole on the Manifold, so the system is closed) and see the readings? Thank you again.

@TutorialGenius Год назад

If you want to see if you have any refrigerant left, just tap the low and high side re-fill ports with a pen; like you would a bicycle tire Schrader valve

@tylerdirden3416 2 года назад

So the knobs on front of the manifold only open/close the charge hose? Or do i have to open the knobs to get my static/dynamic pressure readings once the manual couplers are hooked up, or once i hook up the manual couplers the pressure readings will be present regardless of position of knobs on manifold.

@TutorialGenius 2 года назад

If you want to learn how it works hooked up, I have a video for that. It's in the same playlist as this one :)

@jesus3901 2 года назад

Thank you.

@TutorialGenius 2 года назад

You're welcome!

@prohomevideos Год назад

Since all of your hose connections do not require the pressing of a Schrader valve, does it matter which hose end gets hooked up to the manifold set?

@TutorialGenius Год назад

as long as flare meets flare, i dont see why not

@jacobs7281 Год назад

Thanks for this Video. @ 2.09...For the Yellow tube , vacuum machine or the r134a CAN don’t have Schrader valve and on the other end manifold also don’t have Schrader valve, In this case will the metal insert for opening the Schrader valve if it is used in the vacuum side (for vacuuming) or for Charging refrigerant will impede the flow? Should we remove the metal insert there? Please comment

@TutorialGenius Год назад

I'm not sure im following your comment

@haaatg Год назад

You can just twist the connector a little bit until you see freon coming out

@amirjaber7695 2 месяца назад

Hi, thank you for these information. I have 2 fridges one uses 134a & the second uses R290 . My question do I need a a deferent adapter for the R290. & you be kind send a link for the r290 adapter & Where I can buy it.

@TutorialGenius 2 месяца назад

R290 is refrigerant grade propane, but some of the cans have different sizes for tapping. 7/16" K-28 - amzn.to/3y1l17e or the one listed in this video description. or maybe even others I wouldnt know without knowing the can size

@rylegoodrich 6 месяцев назад

Thanks!

@TutorialGenius 6 месяцев назад

No problem! :) Thank you for supporting the channel, you're awesome!

@brookspact6069 5 месяцев назад

So on the flare side, no teflon tape. What about the other end if it needs to be replaced? Or the gauges if they need to be replaced?

@TutorialGenius 5 месяцев назад

As they say: If it's flare, go bare. If it's straight, wrap it up when you mate

@bryanmathre2620 Год назад

Well done sir

@TutorialGenius Год назад

I'm glad you liked the video!

@332ARA 4 месяца назад

My rental gauges look like that one. My yellow hose has a Schrader valve on one end. The other side is an open hole. Which connection goes on the manifold side? Does it need to be swapped depending on whether pulling a vacuum or filling with refrigerant?

@TutorialGenius 4 месяца назад

If you put the Schrader valve on the manifold side, how will the valve open?

@332ARA 4 месяца назад

I don't know. I'm new to this.@@TutorialGenius

@ernestkanu1247 9 месяцев назад

Thanks

@TutorialGenius 9 месяцев назад

No problem!

@justinsmith6860 2 месяца назад

Dont mean to be a d1!#, but your hoses are connected backwards, the extended connectors, go to gauge, per manual

@TutorialGenius 2 месяца назад

They are not backwards lol 😆

@guestguide2544 Месяц назад

justinsmith - This explains hoses, types, the reason for schrader kind, keeping gas in the hose. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-9gOrT_fSjU4.html

@victorsandoval1060 Месяц назад

So did you assemble this incorrectly in the video you made on how to pull a vacuum and recharge the a/c system? The one in the link in description. I’m just curious if it’s set up different for some reason?

@nills666 Год назад

Which side of the recharge hose goes to where?

@TutorialGenius Год назад

Its already covered in the video

@mikewiley1652 Месяц назад

On my manifold gages, it shows that you did it upside down.The opposite side of the hoses with the curve and are to be connected to the gaujust mine are pittsburgh

@TutorialGenius Месяц назад

It's not upside down. This is direct from the manual

@LC-qi5ff Год назад

When you press the centre Schrader to purge air from the yellow hose, isn’t there still air trapped in the centre of the manifold?

@TutorialGenius Год назад

No it'll get purged! If you have a new set of gauges, its really useful to blow in the holes with your mouth so you understand the passages and how they're connected. I hope you subscribe to my channel soon