How to connect PVS pipe to Cast Iron Pipe using Fernco Coupling

Подписаться 170 тыс.

Просмотров 307 тыс.

50% 1

Subscribe and help me reach 100k subs ❤️. Thank you for your support 🙏
In this video I will show you how to connect PVS pipe to Cast Iron Pipe using Fernco Coupling.
Products used in this video:
Ryobi Reciprocating Saw - amzn.to/3Up5Wlp
THE WRECKER Saw Blade - amzn.to/3VD9mCg
Sanding Sheets - amzn.to/3OTr2qK
Fernco 2" x 1-1/2" Pipe Coupling - amzn.to/3UpobqM
Clamp Driver - amzn.to/3Fll3rR
Purple Primer (you ONLY need a Primer!!!) - amzn.to/3iFucmd
PVC Cement - amzn.to/3uoxUDd
If this video helps you - please like the video and subscribe to my channel.
Other videos to watch:
How to install a Kitchen Faucet Step-by-Step • How to install a Moen ...
How to turn a Wood Countertop Into Marble with Epoxy - DIY • How to turn a Wood Cou...
Simple DIY Garage Workbench and Tool Wall Build • Simple DIY Garage Work...
Thank you for watching!
#diyvideos #plumbing #ferncocouplings

Хобби

Опубликовано:

18 мар 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 190

@calvinskutnik3490 3 года назад

Currently doing my bathroom, complete reno. I have an existing 4 inch cast drain for the toilet. I need to scale that down where it meets the toilet to a 3 inch. This is exactly what I was looking for, thank you.

@CreativeProcessDIY 3 года назад

You are welcome!

@crystalharris1043 8 месяцев назад

Your video was quick and to the point. Thank you!

@CreativeProcessDIY 8 месяцев назад

Glad it helped!

@marypardinek3193 2 года назад

Good job. Liked how you cleaned your cast iron pipe. Thanks!

@CreativeProcessDIY 2 года назад

Thanks for watching!

@williamlindsey2048 Год назад

Nice and clean and simple the way it should be

@CreativeProcessDIY Год назад

Thanks a lot

@woodyblakemore8401 2 года назад

Good video!

@CreativeProcessDIY 2 года назад

Thanks!

@shaunl446 28 дней назад

Thank you

@adamfoulk5865 3 года назад

Perfect thank you

@CreativeProcessDIY 3 года назад

You're welcome!

@HongNguyen-rz2uv Год назад

Great video, please more about main drain pipes under ground basements thanks

@CreativeProcessDIY Год назад

Thanks!

@donnyb3452 2 года назад

Been there, done that! From main septic line to tank. It's the correct way to couple these different types of pipe. Works flawlessly!

@CreativeProcessDIY 2 года назад

thanks for watching!

@Eastbaypisces Год назад

can i use this from galvanized to pvc???

@jackspade2576 Год назад

Absolutely the wrong connection! Do not do this!!! 35+ year plumber here. Use an ARC band or metal sheathed coupler.

@jhoelsantana3946 11 месяцев назад

@@jackspade2576 the hell there goi g to unleash of the rubber is pierced 😅😅

@bestbuddies2649 8 месяцев назад

@@jackspade2576 If somebody was to use a rotary tool or metal snake on this afterwards, and it pierces the rubber boot connection, this all has to be ripped back out. Get the ARC band or "hard inner sheath" coupler like you say. They should have used a powered auger to loosen up the debris. As others have said, it could have been done from the beginning of the video. Replacing intact metal pipe with a rubber boot is asking for disaster.

@gregsonnenberg396 8 месяцев назад

And now im a 😂plumber ! ❤for real awesome video major likes 👍 👌

@CreativeProcessDIY 8 месяцев назад

thanks for watching!

@kalania14 2 года назад

Great video. I have to do the exact same repair.

@CreativeProcessDIY 2 года назад

Thanks!

@JaiKumar-pn2so 8 месяцев назад

Hi there, great video. quick question. I have installed permanent connection to my RV to my sewer line beside the house that leads to the city line. I have installed sewer pump to pump it better, my question is, should keep the black and gray valve ON all the time, if not why not? thanks

@user-me2rz4ed6h 3 года назад

An excellent master, professional. Everything is done with high quality and conscientiously.

@CreativeProcessDIY 3 года назад

Thank you so much!

@teddyboy252 2 года назад

Good job

@CreativeProcessDIY 2 года назад

Thanks

@carrotcake1955 Год назад

Very nice. I have used those rubber connectors. I do worry about them sometimes especially when underground. Would be nice not to cover with dirt giving some access. Thanks

@CreativeProcessDIY Год назад

thanks

@pgreenx 5 месяцев назад

I thought I had to cut a lot of stuff but this looks easy thank you

@CreativeProcessDIY 5 месяцев назад

@user-wg2we4nw7h 4 месяца назад

Hello . Great work . I just finished a similar connection. Im getting some sweating near the band connection. Do you have suggestions how to eliminate that. Thanks

@lillithjones993 2 года назад

Thank you for your video! What size coupling do I need for a 2 inch OD cast-iron pipe? I wondered if the coupling needed to be bigger fit over the pipe. Thank you

@CreativeProcessDIY 2 года назад

you need 2 inch coupling

@Eastbaypisces Год назад

@@CreativeProcessDIY do they have those coulings in 3/4 or 1/2??

@user-rx6ty2tk1z 3 года назад

Great work. I am trying to connect a 2" OD iron drain pipe to the p-trap pipe that will attach to a garbage disposal. My question is, if I buy a coupling tube, how much play can there be when the coupler attaches to the pipe? I am see ing about an 1/8" on either side of the couplers? Is that too much? Will the coupler squeeze enough so there won't be a leak? Any help is appreciated. Thanks

@CreativeProcessDIY 3 года назад

when you buy a coupling you need to be able to attach it to your iron pipe. The better is to have them tight so you can tighten the ring to avoid any leaks in the future. I hope it will help

@conradcrisafulli8269 Год назад

What is the make a model of the reciprocating saw and nut driver? Thank you for taking the time to make this install video.

@CreativeProcessDIY Год назад

I use Ryobi. Not sure about the model

@venessamtz78 2 года назад

During my apprentice plumbing training with the union. I wanted to give u a tip you do not sand the outside of the PVC pipe just the end where u cut the pipe wipe of excess with your hand. The part if cleaning cast iron was a good job.

@CreativeProcessDIY 2 года назад

Thanks for the info

@pjwoo276 19 дней назад

uh oh !

@victorquesada7530 3 года назад

Use the tools you have, but snaking that drain with a rotary tool would have been a better choice for cleaning it out. Some places have code that says the primer has to stick out at least an inch along the exposed sections of pipes (more in some jurisdictions). That flexible nut driver was really cool to see in action though! Nice job showing enough of the project to make the whole thing approachable while staying focused on what I came here for. Thanks

@CreativeProcessDIY 3 года назад

thanks

@Methodical2 2 года назад

I was thinking the same thing. I would sat there and ran a snake up there as far as I could with a snake tool since it is open.

@cgschow1971 6 месяцев назад

primer has to stick up an inch or more? I'm calling it on that one. Waste of primer, no reason to, looks unprofessional. What jurisdictions require this? Bet this is an inspector peeve if true.

@stevejohnson6053 2 года назад

as a plumbing contractor for new construction, this guy is a hero

@CreativeProcessDIY 2 года назад

thanks

@patchworkmountains 3 месяца назад

How much torque are you using with your torque wrench? 80lbs? 60lbs?

@Derpherppington 10 месяцев назад

that lexible driver was useless for this since u got plenty of space already. but its nice to know its available

@nivaldo758 2 месяца назад

Great video. The steel pipe is almost gone in his diameter.

@TerryTolka Год назад

you should have put concrete around the furnco I have dug up to many that have settled and screws up the flow line.

@bexaminer1 Год назад

Would this coupling work under pressure? For example. I need to connect a PVC sprinkler pipe to a cast iron existing pipe. I just wonder if this coupling will handle to pressure from a sprinkler system. I hope it will because this looks like a solution for me.

@CreativeProcessDIY Год назад

Not the ones I used. The couplings you see in this video are only for sewer, drain, waste and vent piping...

@carlosrivera841 2 года назад

When you connected the pvc pipe to the cast iron with the coupling, did the pvc pipe in inside the cast iron pipe or are both pipes the exact size?

@CreativeProcessDIY 2 года назад

They are both the same size

@MMoxie-lb4iv 2 года назад

I am doing a very similar job. I am encountering difficulty cleaning the old cast iron pipe so I can slip the Fernco connector over it. You simply scraped yours clean. The rust and scale I am working with are much harder. Did you prep yous prior to scraping and if so, with what?

@CreativeProcessDIY 2 года назад

No, I did not prepare it. It was in such condition.

@GoogleAccount-ii9sj Год назад

Use a grinder with an abraisive wheel

@devonwesleyhahnkurkowski840 2 года назад

I see that it's for black water, but can I to a line for an outside faucet? Will the constant water pressure mess with it?

@CreativeProcessDIY 2 года назад

I think rubber Fernco couplings cannot be used for pipes with water pressure.

@devilghost 3 года назад

Any tips for keeping surface of drain level with floor?

@CreativeProcessDIY 3 года назад

I have a video on my channel how to do it.

@mts7274 Год назад

1:35 lmao, NO GLOVES??!! 😂😂😂

@CreativeProcessDIY Год назад

@shawn3550 Год назад

Do you and your family shit in your shower or something? 🤔 Easy to tell peeps who haven't done any plumbing work/or get their hands dirty.

@mts7274 Год назад

@@shawn3550 0:51 Looks like the people who used this shower were 'shitting' in it. Most professional plumbers wear gloves when cleaning out pipe like that. Easy to tell peeps who are only capable of amateur DIY projects.

@TheJedimaster6788 2 года назад

when i took off my old kitchen sink pipes underneath...the p trap was sooo corroded, it crumbled in my hand lol. it also took off the end of the other pipe with it :/ fernco coupling saved my ASS and allowed me to connect the broken end to my existing kitchen piping ;D

@CreativeProcessDIY 2 года назад

Great!

@JohnQPublic345 3 месяца назад

1. As a contractor, I have never worked on flip flops. 2. You need a fernco banded fitting

@archerpro137 Год назад

GLOVES BRO!!

@CreativeProcessDIY Год назад

now I wear gloves ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-z14Kq9cRhQg.html

@samsen3965 2 года назад

My old house has 2-1/2 castiron that is rotten and needs change to ABS (A P segment under the shower). I can't find any 2and half to 2 inches clamp. Where should I search and do I have any other option besides Fernco reducing rubber clip if I find none?

@CreativeProcessDIY 2 года назад

I am not sure about ABS. I did my research only about connecting PVC pipe to cast iron

@bigtridentguy Месяц назад

Since comment is two years old, I’m assuming problem solved. For anyone searching for an answer, here’s what I learned. First, double check your pipe diameter calculation. I thought I needed 4.5 inch CI. Realized my circumference measurement was off causing overstated diameter. While my pipes were slightly larger than 4”, it was a nominal amount and the rubber sleeve fit fine. Other tip is to make sure to clean the outside of CI pipe. Sand away/remove any rust or grime from the coupler seating areas. Lastly make sure you use plenty support straps to keep your pipes in place. When you make your first cut through, any existing torque will be released. You don’t want your piping system bouncing around causing further cracking or torquing.

@bpatters69 2 года назад

Would this work for a bathroom faucet? I need to connect the PVC P trap to a Cast Iron pipe that comes out of the wall. The cast iron pipe is not threaded.

@CreativeProcessDIY 2 года назад

I think you can...

@rickeykeeton4770 2 года назад

Are those connections code when in contact with ground? From my research, fernco connections are not code for ground contact.

@onlyinaxj1421 2 года назад

Unshielded fernco is not code. Fernco is fine under ground but needs to be shielded no hub. If he had his work inspected as he should have, he would have failed his inspection

@CreativeProcessDIY 2 года назад

From Fernco website: Fernco Couplings designed for above or below ground use.

@CreativeProcessDIY 2 года назад

From Fernco website: Fernco Couplings designed for above or below ground use. Keep in mind that all states have different regulations and rules. If you are a plumber - provide your license here. Tired of reading nonsense from people who do not even know how to replace even a faucet....

@JTTTTx 11 месяцев назад

Plumber here- not code inside any structure!!! Above or below ground.

@MAGAMAN 4 месяца назад

@@CreativeProcessDIY Idiots usually do get tired of being called idiots. Stop posting videos of how to do things the wrong way.

@WinmanDesigner Год назад

Is it possible to overtightened the rubber coupling? I used an impact drill with a 5/16th driver. Should I loosen it a little?

@CreativeProcessDIY Год назад

You will feel it when it is enough....

@mikeking7470 Год назад

I'm an old man with old man hands, arthritis, etc. I use a nut driver, not a wrench, and tighten it up as snug as I can get it, then wait and do it again in 20 or so minutes after the rubber and the drive band get "cozy". For stuff that gets buried I prefer the couplings with the stainless steel shields, e.g. a Fernco Proflex. There is an 8mm t-handle torque wrench, or 5/16" depending on the brand of coupler, to use with these fittings, I just use a nut driver. If the fittings are hard to get on you can wet them or use a non-petroleum lube, O-ring lube for example. I am not a pro but have never had a fitting leak and have been doing my own DIY repairs 50 years.

@TheTruthAndTheCross Год назад

Yes it is possible. And once you have over tightened it, such as with a power tool, it will strip and never tighten properly again and must be replaced. Otherwise IT WILL leak. It is best to hand tighten as demonstrated in the video. And, as the author advised above, stop tightening when you feel it is enough, because even then some of us can over tightened it. GOOD PLUMBING!

@WinmanDesigner Год назад

@@TheTruthAndTheCross Well it's in there now and has been holding for a 2-3 months. I'm not going to touch it. I only hit the trigger a couple times when I couldn't tighten any further by hand. 🔧

@TheTruthAndTheCross Год назад

@@WinmanDesigner Well, it is best to replace it when it is first stripped out, but in your case, I hope it holds and never leaks.

@barryprobber4921 2 года назад

I like to use silicon on the French connections

@CreativeProcessDIY 2 года назад

You do not need to use silicone on Fernco couplings.

@brentonyon3854 Год назад

Do you make runescape videos too?

@CreativeProcessDIY Год назад

???

@kingofthejungle9300 2 года назад

Hi is primer and cement needed for the hub?

@CreativeProcessDIY 2 года назад

@kingofthejungle9300 2 года назад

@@CreativeProcessDIY ok thanks for the fast response

@CreativeProcessDIY 2 года назад

@@kingofthejungle9300 no problem

@oldowl4290 Год назад

Congrats on showing people how to do this wrong! You need a stainless jacket banded coupler for under slab work. People shouldn’t make videos unless you know for sure you are doing it right and to code.

@stevetassallo1069 6 месяцев назад

must not be in the U.S.

@LoneTinaja 6 месяцев назад

oldowl4290 - the guy said the clamps are stainless steel. When you said a stainless banded coupler is needed for under slab, how is that different from a Fernco rubber coupler with stainless steel clamps? I Googled stainless banded coupler. That brought up various types of images that doesn't make it clear what a stainless banded coupler is. Please tell us more about what a stainless banded coupler looks like.

@oldowl4290 6 месяцев назад

@@LoneTinaja It has a complete stainless sheet /cylinder jacket around the rubber. The two stainless ring clamps are typically riveted to the stainless sheet / jacket. Because it's made for underground use, the stainless jacket protects the rubber and makes it last longer. You're only supposed to use the type he's using here above grade / above slab.

@LoneTinaja 6 месяцев назад

@@oldowl4290 Thanks for the info. I found photos of that type of coupler. Underground at my house a licensed plumber used Fernco rubber couplers 4 inches in diameter with stainless steel clamps but the rubber is not surrounded by a stainless steel jacket. Do you know how long the rubber will last before it deteriorates to the point that it fails? Are there chemicals in soil that eat away at the rubber? Is it also an issue of soil shifting because of rain that makes soil expand, then soil shrinks during periods of drought? Do those processes cause the soil to abrade the rubber or tear the rubber?

@oldowl4290 6 месяцев назад

@@LoneTinaja I assume it's code for a good reason and likely similar to your thoughts. That's all I know.

@drewmole3713 2 года назад

Fernco in the ground/slap not code. Use Transition coupling

@CreativeProcessDIY 2 года назад

what code are you referring to?

@drewmole3713 2 года назад

Plumbing code book 2018 ipc

@centurionforce 2 года назад

@@CreativeProcessDIY UPC- against code for decades....

@TiViD 2 года назад

For those wondering it should be stainless steel banded fernco I believe

@raulgut4030 Год назад

🤔🤫money talks and B""T walks!!😎👍

@Thracianbeatscrixus 10 месяцев назад

not code for Pennsylvania. Should be a shielded coupler there bud

@vipdude141 Год назад

we are remodeling the bathroom and my contractor wants to use this coupling to connect plastic and copper pipe under the floor. I was told that they might last 10-15 years. Is it a good idea to do it this way?

@CreativeProcessDIY Год назад

are you sure you have a copper pipe under the floor but not the cast iron? what exactly is he trying to do?

@Rickey703 3 месяца назад

Advice to DIY homeowners. If you use non shielded couplings backfill with sand to stabilize the pipe. The sag occurs from over excavated trenches that are not properly backfilled. Nothing wrong with DIY. Just DIY the proper way…..

@jivcho 9 месяцев назад

So you're just going to berry that rubber adapter?

@MAGAMAN Месяц назад

Yes. Those are underground rated.

@GaryYoung-eq1ph Год назад

Can connect to metal 2" wall pipe?

@CreativeProcessDIY Год назад

sewer pipe?

@AGoodHandyman Год назад

Wa that a toilet sewer line or lav?

@huntera123 10 месяцев назад

Hmmmm....I have done exactly that twice to replace a 4" iron elbow. Both times the soil chemistry makes the flexible coupling extremely stiff so the stainless steel ring clamps are not applying friction. Then natural soil movements pull the repair apart.

@bigtridentguy Месяц назад

The shielded version of couplers solve for that. Instead of a rubber sleeve and two hose clamps alone, they also come with stainless steel “shields” that cover the rubber sleeve making it rigid. The added strength keeps your pipes aligned and doesn’t require a soil backfill. It also deters rodents from chewing up the rubber.

@shimulislam8539 2 года назад

6" cast laran pipe fire line cunet bocar boss how canet

@CreativeProcessDIY 2 года назад

I do not understand.

@jonathanjames10p 2 года назад

Was wondering if anybody can help me try and help complete this job, basically looking to install a water filtration system but have cast iron pipe running throughout the house, not copper or plastic. The problem is to install the system I usually use SharkBite or plastic 3/4 or 1in. connections just never had to install a system in a home with galvanized steel or cast iron pipes and plumbing.

@CreativeProcessDIY 2 года назад

Try to thread your galvanized pipe and make a connection. Use Tap and Die Set.

@JuanHernandez-sk4mf Год назад

Should of used a Grinder to cut cast iron

@CreativeProcessDIY Год назад

good idea to use a grinder, agree

@JuanHernandez-sk4mf Год назад

Should of used 5/16 bit with drill to tighten up band

@CreativeProcessDIY Год назад

you cannot use drill to tighten fernco couplings. you can tighten it up manually. read instructions

@arnelgajitos4947 2 года назад

How to cement pvc to cast iron pipe?

@CreativeProcessDIY 2 года назад

No way. The ONLY option how to connect pvc to cast iron pipe shown in this video.

@randallriggs2159 5 месяцев назад

The drain should have stayed 2" all of the way You will have better flow

@JuanHernandez-sk4mf Год назад

P trap should of been 2” also

@teljug 5 месяцев назад

He did oright and i am proffy plumb

@JuanHernandez-sk4mf Год назад

Should of used husky no hub band 4 strap band

@fixedit8689 Год назад

Dressed for the job

@CreativeProcessDIY Год назад

who cares?

@jp410 2 года назад

Thanks for the video. It makes me sad to see that flag and think of what people are going through. God bless them and support them.

@CreativeProcessDIY 2 года назад

thanks for watching

@anyhonyardito3510 Месяц назад

Where did this guy learn 🤔

@she219 10 месяцев назад

I can tell he's not a plumber

@dunkjones3725 2 года назад

Really? Flip flops? Why not just keep it 2"? Would be a lot easier for cleaning purposes in the future

@CreativeProcessDIY 2 года назад

These are not flip flops. They are called slides. What the difference it makes if I work in slides?

@misteriguana2748 Год назад

I do all my work barefoot. From tile/concrete demo to finish carpentry. I only wear something on my feet when going to the landfill or shopping. Work comfortable is my saying.

@coyotes4321 2 года назад

Mmmm idont know if thats the correct way,🤔,, thats a way though. 🤷‍♂️

@CreativeProcessDIY 2 года назад

Thats the ONLY way to do it.

@geob8417 2 года назад

@@CreativeProcessDIY wrong ....thats not only way and in mass that is against code

@jacksplumbingvideos7147 2 года назад

@@CreativeProcessDIY you can use a no hub coupling.

@MAGAMAN 4 месяца назад

It's the wrong way to do it.

@zachmccann1758 11 месяцев назад

That’s only illegal. If it’s outside the building it Hass to be shielded.

@richardjoseph8683 2 года назад

Illegal fitting for underground connection. It must be a shielded coupling. This guy is clueless. Don't do this!!!!

@CreativeProcessDIY 2 года назад

illegal???)))) read instructions on manufactures website....

@blt981 Год назад

@@CreativeProcessDIY sorry friend don’t know what country your in but comment is correct the coupling you used has to be protected from rocks debris. There are ones made here in America that have metal sleeves over both ends . It is torqued down with specific lbs on the brackets. Let say a person backfills your hole with fill that has a rock of small foreign object of if it’s filled with draining gravel. Your rubber unprotected fitting can easily be torn or pierced. The metal clad hubs are made specifically to protect the connection…..it’s ok you tried to do better….be open to crisis by professional plummers. It’s not good to pass wrong info that can cause complex trouble. Don’t mind what’s on a little label. Look at the building/ plumbing code that’s shat guides us her in YSA…

@Joe_Brown99 11 месяцев назад

@@blt981 That gave me a headache to read

@pedroavillarruel4740 11 месяцев назад

He using a ryobi what do you expect

@Jaydayallday 9 месяцев назад

@@pedroavillarruel4740and wearing flip flops with socks on to perform lol

@soccerkills 9 месяцев назад

No gloves hmmm

@dakotahuff2276 3 года назад

"very fASt" LMAO people using reciprocating saws instead of a grinder on cast iron is hilarious

@CreativeProcessDIY 2 года назад

thanks

@olliebama9323 2 года назад

The fastest I've found is to use a grinder w/a continuous rim diamond blade. No shaking of the pipes upstream that might initiate a leak at the next hub, and..... it cuts fast! Also, less chance of unwanted shattering/breaking of the cast iron you are trying to keep. Absolute control with the diamond blade for a clean, straight, end-cut; if it's not perfect, the diamond blade can trim/grind the merest amount off to make it right. If necessary, and if you are unable to get to the backside of a pipe to make the cut, cut a section out on the front side big enough to get the grinder inside the pipe to continue cutting. Absolutely wear gloves, hearing and eye protection, and a respirator. I showed this trick to my plumber years ago- he'd never heard/seen it done this way; went out immediately afterwards to get some diamond blades...... lol. YMMV

@shawnparvini8490 2 года назад

This video settles it for me... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ACU1KeVfJa0.html

@bobbytrujillo Год назад

@@olliebama9323 I use sawzall with the Diablo thick metal carbide blades. If you know how to use the sawzall you can avoid the vibration. Just my preference.

@Riga352 Год назад

Do not trust a guy who does construction in his sandals. There is so much wrong with this video I don't even know where to start

@CreativeProcessDIY Год назад

I am working in my own home. You can wear special clothes, buy the most fancy tools available on the market but if your hands grow from your ass - it won't help you.

@michaelmatus4556 4 месяца назад

Biggest common mistake.fernco not allowed in envelope of house.ck your local codes

@supersixone7414 2 года назад

wear gloves when using a snake people

@CreativeProcessDIY 2 года назад

why?

@georgelee6857 2 года назад

Wear some gloves

@CreativeProcessDIY 2 года назад

why?

@ld7179 11 месяцев назад

страшный акцент

@CreativeProcessDIY 11 месяцев назад

thanks

@frankcasendino8662 4 месяца назад

Wrong fitting for under slab connection 👎

@f.demascio1857 Год назад

PVS? Bruh...

@CreativeProcessDIY Год назад

what is wrong with PVS. Most of the plumbers are using it

@MS-gn4gl Год назад

stop using milwaukee blades for cast iron. they suck and you'll go through 2 to 3 times as many than you will hte diablo cast iron blades.

@Whosurdaddy71 8 месяцев назад

How not to connect 😂

@ryanperry9838 10 месяцев назад

U can tell he’s a total noob, Ryobi tools, purple primer and buried ferncos lol the path to disaster, this would fail inspection, no worries more work for real plumbers. On to the next job to tie in some slinky drains and shark bites! Big box stores sell all type of crap doesn’t mean u should use it.