How to diagnose a Faulty Crankshaft Position Sensor (CKP) - 2005 Pontiac G6 

Best step by step auto repair video I've ever watched. You are a GREAT teacher.

Good tutorial! Very well explained with straight-forward terms, thank you.

Never seen such a great explanation and diagnosis. Love from India

Good video, but dear lord, the clicking-gears-sound on the instructions graphics is annoying.

اTHANK YOU SO MUCH GOOD INFORMATION

i just got this error today in corolla 2012 . will check doing this

Hi, I just replace the crank shaft sensor, and the engine still shaking, if I don't perform the relearn procedure what will happen?

thanks! i recently put in a NEW (but bad) CKP sensor and its apparently shorted internally- screwing up my fuel level gauge, ignition coil/ignitor(?) and setting off a host of other selonoids- et al! I cleaned all grounds, rebuilt my fuse box, new ECU, cleaned everything........no changes UNTIL i just now decided to swap back in the old CKP sensor. All the electrical clicking, etc went away immediately and Im not going thru the KEY RELEARN process for the new ECU

Nice detailed video, but I have to comment that the term "Current voltage" does not exist. You really measured the voltage (only) at the sensor.

Thanks alot for this uselull informatinos

Oh I thought you knew something, no one else did. See ya!

Hi, I replace a Crankshaft position sensor and I still have a crank no start condition. I don't have a scan tool and I don't want to take care to a shop because they will ask me for a lot of money and I don't have that. What can I check? I don't have spark in any ignition coil, I checked the fuel injectors and when I go to crank it it light up. Should I check my ECU? Thank you.

When this sensor goes out, will the vehicle turn off, even while the vehicle is in motion?

No crank condition....customer had it towed in?? or No RUN condition...cranks over fine but will not run??? Still towed

I Own A 1999 Chevrolet Tracker 2.0 With the Same P0335 Error And I Dont Know Where The CrankShaft Sensor , Any Idea ? Help please !!!

crankshaft and sensor are different?

What parking brake? Mine fell out years ago.

How can you tighten to proper specifications if you dont have access to said specifications

I think may be whats wrong with my kia, but I dont want to just ask a mechanic to check that part for me like I know for a fact, I wish I could just check it myself, n due to the virus I can't get a auto part store to use the code reader right now so I'm not sure what to do, I had my fuel pump replaced cuz they thought that was the problem but its still doin the same things, it's really frustrating spending all that money n time for it to not be working right still, the rpm need just drops n it stalls out every day at least once or twice and I cant get it to do it for them at the shop so they just tell me theres nothin they can do cuz I guess apparently they dont get no codes up either but the check engine light comes on too but then it goes back off by the time I can get it to my dealership to check it so I'm not sure if it will send them codes

Proper specs? With a regular rachet? You could of also turned your wheel to give yourself more room to work :)

What about if you don't conduct the relearn process, what will happen?

How the EFI know which cylinder to inject? How does the EMS know which piston it is at and in which stroke based on the CSP?

Thank you i have a crank no spark im about to test Crank position sensor 😁

I have a 2000 Merc e320 that starts, runs 10-20 minutes, quits and won't start for about 45 minutes. No codes set. 62,000 miles. Could the crank position sensor be the problem?

Couldnt u have disconnected the wire at top of engine instead of under?

I changed mine but my car started accelerating on it own at 40mph

2002 Kia Sedona has a crankshaft position sensor and a CAMSHAFT position sensor, would someone know if it also has a sensor on the flywheel?

Hello I need help I have the same for mazda 6 the car does not have spark can I check in the same left and right not the meddle

Great vids! Does this ohm measure works on every 3-p crankshaft sensors? I have an Audi A3 1,8T -99. And I have no codes when I read out. Sparks on all 4 sparkplugs. Fuel from every injectors. The fuel pump and startmotor is ok, but the car won't start. So I have just loosened the crankshaft sensor and want to see if it's good or bad by measuring resistance. Shall I hold on the pin to the left and right and get an value?

Why go through al this? Just look for tach needle movement during cranking?

Crankshaft has been replaced but the fault keeps on coming What could be the problem Car is an Isuzu 3L DTeq. Thank you

hi where can i find the crankshaft positioning senor on a 2006 monte carlos SS 5.3

Please what's the name of that scanner

Nice video just didn't explain the symptoms.When they go out, does the motor turn over or act like its siezed ?

Isnt there two crankshaft position sensors on a pontaic g6. Front and back?

if 6.25 ohms resistance is good , would a 3.08 reading be a failing sensor? I have not had any codes for a failed cam sensor, but have changed many different parts trying to clear a p2195-97, p0106, p0300. could these codes be caused by a failing cam/crank sensor? 07 f150.

I drive a 2006 Pontiac G6 GT with a 3.5 L V6 engine

use a scope, ohm check isn't as good as looking at the actual sensor.

That gear sound is so distracting, would be a much better video without it. One other thing for dyslexics and the sort, when "reinstall" is used here he is not putting the original back in but rather the new one, so technically speaking the instructor should simply say "install" since it was never in, in the first place.

Toyota

that intro is to fukn long.