How to Diagnose Starter Problems on a Honda CBR 600 RR | Partzilla.com

Подписаться 178 тыс.

Просмотров 190 тыс.

50% 1

Buy your multimeter here:
www.partzilla.com/product/aft...
Learn how to diagnose starter problems on a Honda CBR 600RR motorcycle. We’ll check the battery, inspect the fuse, evaluate the starter switch, and test the starter relay.
Read more about troubleshooting motorcycle starting problems here: www.partzilla.com/blog/honda/...
VIDEO HIGHLIGHTS:
Test the battery - 0:55
Inspect the fuse - 1:25
Evaluate the starter switch - 2:25
Test the starter relay 2:45
Honda CBR 600 RR parts here: www.partzilla.com/parts/search...
Talk to us:
Twitter: / partzilla
Facebook: / partzilla
Instagram: / partzilla
In the video we’re working with a 2008 Honda CBR600RR, but you will have similar steps for your Honda motorcycle. If you’re not sure whether these steps apply to your motorcycle, leave a comment and we’ll get back to you.
RELATED CONTENT:
Testing the Charging System on a Honda CBR600 RR:
• How to Test the Chargi...

Авто/Мото

Опубликовано:

1 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 308

@tyler.3015 4 года назад

Great tutorial John helped diagnose my problem!

@DanHall64 5 лет назад

Great tip! Fixed my problem, thank you :)

@andruamaru2860 6 лет назад

the first thing was what rectified my issue, thanks mate 👍

@alfaer. 3 года назад

very complete and full of knowledge

@nickeleytheriou5005 Год назад

thank you very much for the absolutely useful and very interesting videos you are making there !!!

@bboyxbox 2 года назад

I learned a lot from this video thank you very much

@kobayashimaru8114 3 года назад

Great video! One thing that confused me at first was when you were testing the starter relay. The video shows you had the wiring harness disconnected but doesn't show you re-connecting it. This made me question whether the wiring harness was to pass power from switch or to the starter. Also, the camera angle doesn't clearly show the actual removal of the power cable from the relay (I guess it can be inferred by your hand movements). But seeing the beefy relay terminals with my own eyes is what made it obvious that's what the starter is connected to.

@adamjohnson6007 4 года назад

So much expertise. Nice and concise. Always helpful

@teekay4282 25 дней назад

Thanks for the video, this helped me out a lot.. killed two birds with one stone .. my pump wasn’t priming , checked every single thing but didn’t work, the noticed I couldn’t start the bike just to figure out the switch was bad.. Played with the switch alittle, then the pump primed and the bike started up

@live4windnface1 4 года назад

Thank you for the informative video. This helped me. I found that my HID ballast had blown which was the reason my bike wouldnt start. I switched it out and now im back on the road.

@MsFshuffling 3 года назад

I have the same problem what did you switch out? The bulb or starter

@FOXMEDlA 2 года назад

@@MsFshuffling did you figure it out?

@donniehill3952 7 лет назад

You just saved somebody a BUNCH of time and money .

@PartzillaParts 7 лет назад

Boom! Two things there's never enough of! Glad to hear we could help, Dennis.

@josealfredocervantesjimene9799 5 лет назад

Gracias #saltillo saludos ...salí del problema 😎

@BillzByABillion Год назад

Great video. Thank you.

@r91motorswelcome79 2 года назад

Brilliant video

@aizenauditore8777 7 лет назад

thanks so much you helped out a lot!!!!

@PartzillaParts 7 лет назад

Awesome! Glad to hear it, Aleksey. See you around the tube.

@warrior1485 Год назад

Thanks .. this help me..👍

@sinvaocoi 7 лет назад

hi I checked everything as you did in the video. but I when I connect the positive terminal to the yellow red stripe wire the starter does not make any noise. what could it be? starter is bad? thanks.

@robestudaddy 5 лет назад

Hi John! I followed every step in this video and my request is: Would you please make a video of how to get to the starter motor on a 2006 CBR 600rr I have taken the air box , gas tank, disconnected the negative cable that goes al the way to the starter but from that point I do not know how to disconnect the Throttle and the cables so that I can get to the thermostat and be able to reach the starter at last. I got some parts from Partzilla on the way to finish the job and I will certainly appreciate your help.

@akielfrancis4442 4 года назад

Nice video my 2004 rr wont start when hot could it b the starter?

@BlueDeamonGaming 7 лет назад

Hello I own a 2007 cbr600rr I have a problem with my headlights that my high beams work but my low beams don't turn on. The bulb is fine. Another thing I thought about checking is the relay, I just can't figure out how to get the headlight relay out to check it. Is it just a pull out? Or is there like a clip holding it in? I checked the fuse, it's fine.

@malikhouser2825 6 лет назад

Hi I'm having a problem with my cbr900rr 1999 the 10a fuse keeps blowing when pull off the odometer back break light horn go's out how do I locate the relays for that not sure but thinking that's the problem

@mrbojangles155 4 года назад

Any chance you’d do a video about if the motor turns over but nothing else happens ? I’m currently in that situation and after about a month of searching someone mentioned that my tip over sensor could be bad/burnt out ? Have an 05 cbr600rr and it seems most of what you do goes for that as well

@chanuperera7612 3 года назад

When I put the clutch in the gear of my Honda MC22 RR bike, the neutral bulb lights up, I replaced the diode but the problem is the same, thank you for providing a solution

@Kintamani1402 5 лет назад

My cbr 600rr 2008 sometimes hard starts when warm Cranks good but doesent fire up only when its hot I have to crank it two times to fire up Any clue? Battery good

@craigmusicss 5 месяцев назад

Thanks for the video! Question for you I'd you get time. I've done all the steps and bike still won't start, I removed starter motor and attached positive and negative to it and it fired straight up but won't start the bike. Can the start be to weak to move the engine or is it likely something else?

@ricardoveramsm2487 5 лет назад

Gracias hermano , ya prendió mi moto

@aronob Год назад

No es tu hermano….. Es tu padre …..

@christopherpenn764 4 года назад

Had a question , my 929 shut off and dash lights shut off simotaniously and blown a fuse , and keep blowing the 30 amp fuse , and 2ont start

@Apasia 4 года назад

Would this be the same.for a.08 cbr 1000rr? Relay issue with headlight. Turn on bike, it turns on but does not stay on...

@justinacosta8329 5 месяцев назад

so i am having a problem when im hearing a clicking noise when i click the starter but it wont start? or engine wont turn over? the guy said he just put a new starter in it but idk got a new battery in it and im not sure im check the fuse and see whats going on .

@williamkoehler9048 Год назад

So when that main fuse was blown will the clock on the gauge cluster still work? Because mine the clock is on, the battery is brand new and as soon as I turn the key there’s nothing on the gauge cluster at all

@jasonmortimer8397 3 года назад

Hi guys, I have a starter motor for a 1992 honda 250rr mc22 that is possibly spinning in reverse, what direction should a starter motor spin if the drive gear in motor is facing you.

@JokerBoySkrapp Год назад

Hello, got a 09 honda cbr 600, they guy said something about the previous owner did something with the headlights and now the bike wont start, it turns over but wont start, says it needs and ignition, but before i buy anything was hoping for feedback. I was going to just hot wire it but he said that it would mess up the cpu or something i dont know…😭

@jonanddarlenesoto9422 7 лет назад

I have a 2004 Yamaha YZF 600 r my problem is when starting cold it turns over then like a metal crunch then its seizes and won't turn over. it takes a while and multiple start button pushes before it starts what can that be?

@gmike912 7 лет назад

Any tricks to help pull off the cover of the main fuse?? Mine seems to be very difficult..

@litoswayzie2968 3 года назад

What happens if you complete the circuit by using your method and the bike starts? What would be my issue? Currently where I'm at. Replaced the solenoid did not solve it

@Hughie1987 7 лет назад

I have an 09green and black 600rr! my bikie shut off on me at a stop light after getting gas, the bike did sit for about 2 months here in pa from november through december

@DarxusC 5 лет назад

I bet the service manual for most bikes tells you how to test the internals of a starter too. Under electrical system / starter motor inspection. There should be continuity between armature segments. There should be no continuity between an armature segment and the shaft. Careful, because I measured some continuity that turned out to be my skin.

@g.j.8390 5 лет назад

Hello. skills have Honda cbr 1000 pp 2009. I arrived at home, he drowned and the second day he did not wound up. Pat pashli diagnostics, and the diagnosis does not see the block immobilizer. Say it was your prktiku? and if that was what the problem was? Thank you in advance.

@shanetalley1616 4 года назад

I have a 2006 honda cbr 600rr. An I just ordered a starter solenoid hopefully it will start now.. an also have a brand new battery 3weeks ago..if it doesn't start after this what else do I need to look at?

@PartzillaParts 4 года назад

Wiring for damage or corrosion

@Aronelshannon 3 года назад

Hello I have a 2007 Honda cbr 600rr the top sensor was cut out and wired up bike was taken apart I put it back together but for some reason I can’t seem to get the fuel pump to prime for nothing or even get the bike to start can you please help me pls I need help ?

@aizenauditore8777 7 лет назад

so I have a question I cleaned out my starter and tested it and it moves pretty good even from my pretty low battery that I haven't used in a couple months and so after I put everything together I checked relay fuses they're fine but the bike was making a buzzing static noise from the relay every time I pressed the power button and so I charged my battery and I could actually hear the starter Turing over but its very slow and isn't enough to power on the bike do you think that the battery can't hold a charge anymore or something? or its something else?

@PartzillaParts 7 лет назад

Hello Aleksey. What you are describing sounds a lot like a dead battery. That is the first thing i would check.

@etherportel2322 2 года назад

I'm so amazed that I can't find not a single video of a 2007 cbr600rr....

@waynedavis9951 Год назад

Do you have a replacing the starter video?

@adarshkeswani2319 6 лет назад

Very nice video. My immobilizer light keeps flashing when I turn the key. The bike had been recently exposed to water. Any ideas ? I will try and look at the fuse this weekend.

@PartzillaParts 6 лет назад

Sounds like an ignition situation. Double check the wires are good and tight. Blow out any moisture that may have gotten in there. With water, it could be anything electrical that got wet and is now shorting.

@oscarmunoz2172 4 года назад

How I can regulate my rpm on 2008 cbr 600r? I cannot found the idle adjuster

@vincentgarcia2702 5 месяцев назад

What did you use to bypass the switch? To complete the circuit

@cyberBIGGT 3 года назад

If you hear a loud screech while riding and then when you slow down the engine cuts off and and won't start again, you smell a faint burning smell and your battery is good you most likely need to replace the starter, correct?

@MotoBikeMike 7 лет назад

My cbr600rr powers up fine as well as my fuel pump. My battery is reading good numbers just barely under 13 volts. Now when I go to turn my bike over I get a machine gun like clicking sound from the tail of my bike I guess you could say around my seat and my gauges turn off and when I release the starter button the gauges light back up. ?? Any ideas if this sounds like a starter problem

@PartzillaParts 7 лет назад

Load test your battery. A static test isn't enough. Make sure all connections are tight and clean. If it tests good, start checking your ignition and button wires for a short.

@adriangarriques440 6 лет назад

Your videos are the best. Quick question. I have a 2006 CBR 600rr, she cuts off every time I stop at a light and I have to turn it back on. Sometimes I have to pop start it in 2nd gear after changing out battery and spark plug. Haven't checked the stator but I feel thats what the issue is

@PartzillaParts 6 лет назад

Test your regulator first. Sometimes, it gets hot and just shuts the motor off. It's better to test the components than just blindly replace. You'll save some money.

@adriangarriques440 6 лет назад

Partzilla thank you, I will be sure to start there.. I'll let you know how it turns out.

@stone4778 4 года назад

I need the starter relay but can’t find it on website

@illwillification 5 лет назад

Thank you! This just happened to my Cbr F2 600. Won’t crank seems power is drained and shortage of circuit power.. I believe the stator rectifier is the issue ..

@PartzillaParts 5 лет назад

Run the tests before you start buying parts!

@illwillification 5 лет назад

Yes of course! Battery gets charge. Starting bike and running, but bike now gets hot now too soon..

@PartzillaParts 5 лет назад

If it's running too lean you will have issues starting and it will get hot quick. Might be something to consider as well.

@illwillification 5 лет назад

Yes of course. Seems like its not getting much water from the pump... Another fan would be nice too

@jeromemeyers4167 Год назад

I have a 06 cbr 600 rr.. head lights come on and cluster lights up. The bike cranks but won't start over and run. It happen after I replace the front fearing

@kngarthur1975 11 месяцев назад

I have a problem I turn on the my bike which is 1998 cbr 900rr all fluids and gas once I hit the start button just a clicking noise please help

@yousifalmosoy7378 4 года назад

M.r john i have honda cbr 1000 rr 2007 i have a problem weth it is after 5 .6 Rpm go fast to the top Rpm but the bike not exsleritng

@allegravickas355 5 лет назад

Hi, this is in the same vein as the most recent comment, regarding '05 CBR600RR. The battery now only has ~10 V, so powers the dash, lights etc, but obviously won't start the bike. When pressing the starter button, can hear the same very loud click click click (like a taser), and bike obviously won't start. Before the battery went flat, there was no clicking noise, fuel pump primed and engine cranked but no ignition. Any suggestions? Cheers, thanks

@PartzillaParts 5 лет назад

It will click like that when it has insufficient power. As for the initial issue, check you are getting fuel and spark...check plugs and coils.

@helloitsme1149 6 лет назад

hello i have a cbr 954rr my engine starts so easily when cold but if i try to start it when hot it doesn't start engine keeps on turning though. if i jump start it it starts right away!. what might be the problem i really need yout help

@PartzillaParts 6 лет назад

Test your regulator rectifier. When they start to go bad, heat affects the component.

@cultistpriest1872 3 года назад

My 08 cbr600rr is sputtering on low rpms 7k blow any reason why? I have no clue

@adriansy365 6 лет назад

Dude thanks for making this video but i got a question. I just bought a 2007 cbr1000rr from a friend and he hardly rides it. I dont have a multi meter but maybe i should get some. When i tried turning my bike on. So switch on kill switch is on then i click the starter. All of a sudden the screen dying out and trying to crank the engine. It will start after 3 or 4 crank. Does it mean i need a new vattery??

@PartzillaParts 6 лет назад

Start with simple first. Health test the battery or get a new one. You can't do accurate tests without a good battery anyway.

@shelliediaz9904 7 лет назад

Thanks for your video....i did everything you said and it still won't crank over so now I will go buy a starter, but where is the starter located? My bike is a 2005 cbr 1000rr., thanks Ed

@PartzillaParts 7 лет назад

Should be right side, just under frame. To access the entire thing, you will have to remove the tank.

@bryantschroder5479 2 года назад

My honda 600 cbr rr 2004 just stopped while riding today. the oil lights stays on and the oil picture stays on. it cranks just wont start. just serviced a week ago

@allthisfitsverywell4203 3 года назад

I have a bike it's a 2003 Honda CBR 600 F4 and when you hit the starter button the bike will start but as soon as you let off the starter button the engine cuts out what could the problem be

@hegedustamas3 3 года назад

Hi, here is my problem (CB500 2002), hope you can advise something for me to solve it. I swithed the ignition ON then i pushed the starter button suddenly power cuts off (small clicking noise came, dont know where) since then no power at all. Fuse box checked, all good, main plug fuse ok too. what elso could have gone wrong? thanks!

@PartzillaParts 3 года назад

Hello hegedustamas3 Did you by chance check the voltage of the battery? this sounds like it could be a weak battery. Hope this helps!

@lukebond431 2 месяца назад

Hi I have a f1 light on and fuel pump won't prime but I'll try it again a few hours later and works fine with no f1 light and fuel pum primes. Anyone know what's going on because I dont

@lilbuddylee131 7 лет назад

Afraid I may need a new starter. Do you have a video for replacing one. I get a hum from my relay even after I replaced it.

@PartzillaParts 7 лет назад

It's on the list, but the video has not been done yet.

@ilkanackkapu7804 Год назад

Motorum honda cbr 600 rr. F1 arızası var ne yapmalıyım

@NoName-db9wo 2 года назад

I having trouble on separating plug on the stater rely to check the fuse

@zakiyezdery 7 лет назад

I have a 2006 cbr600rr and it all works in terms of turning on, riding, front headlights and high beams but the problem is that the indicators, horn and break lights don't work, it was working perfectly fine about 4 days ago but jst randomly stopped working today. Can anyone help on with this problem?? all the wiring have not been touched or anything it jst randomly stopped working. thanks in advance!!

@ricardomcdonald8239 5 лет назад

Can two different casein cause the 06 600rr to not starting back when its I've check all those that you told me about and am still getting that problem

@stephencarter8264 4 года назад

Can anyone help me with my CBR600f pgm 2003 rev counter not working speedo works indicators work temperature works just not revving after installing gear indicator

@eddy-nd7nh Год назад

I bought a new battery it started no problem but after I turn it off i try turning it on again and it won't start unless I Jumpstart it even tho the battery is new

@randygarcia4565 5 лет назад

I have a CBR600RR 2006, I replaced the starter relay but still no joy. If I jump the yellpw/red wire it cranks. What would be the next steep? Starter push bottom?

@PartzillaParts 4 года назад

Could be the switch, or a bad wire.

@ArturK1M 3 года назад

Thanks for the video. So I started the bike by bipassing starter button and it did work. Does that mean i do have a problem with my button? Or wires i suppose. Thank you.

@williamreilly4676 3 года назад

I have the same question lol I sent 12 volts to the red/yellow wire that goes into the starter solenoid and it fired right up. Did you figure it out?

@ArturK1M 3 года назад

@@williamreilly4676 Not yet but will start by replacing the relays as I also have a problem with my headlights, low beam isn't working and high beam I can't even switch off. I might even try to open the button and see if it's not malfunctioned. Will post here if I solve the problem.

@williamreilly4676 3 года назад

@@ArturK1M after I commented this I tested the wires, no power. So i opened up the kill switch/start button, cleaned the contacts, then tested it again, still no power. Chased wires all the way to solenoid and all seemed fine, ended up peeling back the heat shrink/protective sleeve right below the kill switch and two of the wires were pinched clean in half 🤦🏻‍♂️ I'm going to splice them and see if it works today. 99% positive it was the issue

@ArturK1M 3 года назад

@@williamreilly4676 The first connector coming from steering bar under right fairing below tank cover. That was the problem, I literally just touched it and tge bije fired up. Either dirty, loose cable or snapped wire. Let's see, all I did is clean it so far.. Thanks for good conversation!

@laquiltonpruitt690 3 года назад

Has anyone experienced in my case my bike turns and cranks after a few seconds rough idle Fi light jumps on than she dies, turns and cranks right back up but does same thing... any suggestions

@keithstephens756 4 года назад

Mine keeps melting the fuse. New relay stater rec. ?

@Pjma01020805 3 года назад

my 2008 honda cbr 1000rr does not start because no spark coming through. Where should I turn to fix that problem?

@Goldrvssh 7 лет назад

I put the meter on the starter relay and I got no click and the meter still read 0

@justaguy4real 5 лет назад

so a fuse blows when too much power surges so its protected?

@DarxusC 5 лет назад

If there's a short in something like the starter, the fuse blows, so the wires don't melt.

@darksorceresszyra9467 2 года назад

Thank you. I am working on a 2006 with the end result being the end result; starter. lol

@d3klin 2 месяца назад

There is no OBDII on 2008 model?

@robestudaddy 5 лет назад

Hi Would you please clarify to me the last step where you check the connectivity of the starter relay did you disconnect it from the bolts and the red connector? Thank you Partzilla.

@PartzillaParts 5 лет назад

You disconnect it from the starter so it doesn't attempt to start the unit.

@robestudaddy 5 лет назад

Partzilla Thanks! I appreciate your help!

@user-rl7qk5ov3b 5 лет назад

i have motor honda 929 is proplem wont start help me

@glumGlumm 7 лет назад

My fuel pump relay under my seat is making a teaser sounds like. Ive test the charging system my stator look ok but my bike randomly dies on me. My baterry is new and spark plug replace. What else do i look for issue on my bike? I only heard it once now its working normal again im still cant ride it since its acting up.

@PartzillaParts 7 лет назад

Test the regulator rectifier first, just to cover the charging system.

@Demonking2323 4 года назад

Please do a fuel pump problem video!! The two clips that connect to the pump (black goes to the sensor and brown goes to the pump) I use a volt meter on the black and it has 10.56 volts and the brown has 0.00... the cords look to be fine and relays and fuse are not blown...any suggestions😫 fuel pump was on a tank that has been sitting for a long time gas smelled like varnish. Cleaned the tank and changed the pump inside it, but not the whole entire fuel pump. Fuel pump wont prime.. please help

@Kendrickshayesjr 7 лет назад

It would be great if y'all can make a video of the real electrical problems these bikes have.

@PartzillaParts 7 лет назад

Well, you might have to narrow down the "real" electrical problems and we can try to put something together.

@drew9170 2 года назад

Ik this video is old but please for the love of god, I have a Cbr600rr 2008 model I can start my bike and ride it. but my cluster doesn’t work it shows me the indicator for my headlights and turn signals along with the clock for whatever reason but I cannot get the green neutral light. I get no rpm or speedo readings, temps, and odometer readings not that I need them but it would be useful. Your videos have taken me a long way with maintenance on bikes but can’t figure this one out :/

@eazygetgreezy7548 6 лет назад

I have a CBR F3 95 and is blowing fuses replace the fuel and carburetor fuses and the one up under the seat where the relay when I replace the fuse it will crank up and run for a while but it will blow again and for some reason my start switch won't work so I replaced it now I'll see when I press the start button the lights will dim but it won't trigger that starter

@PartzillaParts 6 лет назад

Check your wiring from ignition and switch, you likely have a short somewhere.

@joeceline2366 7 лет назад

my husband has a 2012 honda cbr 250r that start s but turns off he puts gas on the coberater and it turns on but turns off dose anyone now what could be wrong

@rushaneshaw1104 4 года назад

Hey my bike is have the same problem not starting it make a click sound but it would just now start can u help me out

@PartzillaParts 4 года назад

Check battery, wires, solenoid...

@vincentmounsey 6 лет назад

@Partzilla how do you adjust the throttle idle I can't seem to find it

@PartzillaParts 6 лет назад

There is no manual adjustment on this unit.

@vincentmounsey 6 лет назад

Thanks for getting bk to me

@johnnytrillberg5185 6 лет назад

I have a 04 Honda cbr f4i and i have replaced the battery as well as the fuel pump and relays I have also replaced the ignition key the original key just turns on the fan , no fuel prime , still cranks over but no start the new key no fan when turned on no fuel prime and cranks but no start do you have any idea I have checked everything the bank angle sensor kickstand sensor you name it they all check out fine but for some reason I cant get the fuel to prime please help thanks

@PartzillaParts 6 лет назад

Did you check the harness between all those components? That sounds like best case scenario. Worst case, ECM? Check everything you can before you jump to ECM.

@gallupjoshuad 5 лет назад

Johnny Trillberg, and Partzilla, I have a 2006 cbr1000rr same problem as Johnny I'll be checking all this, Johnny did you fix yours or find the problem, and is anyone aware of any recalls on this more than common issue, my. ike dose not have a diode, maybe Partzilla could do a video on this issue seeing as how it's so common

@antiiv11 5 лет назад

Would a low power for battery cause the fuel pump not to prime when engine cut off switch is flicked on and off. The ignition cranks up and the relay clicks just no prime

@PartzillaParts 5 лет назад

If it's dead. It doesn't require much to prime the pump.

@mrthecrev 4 года назад

I have the same problem relay click, ignition work and kill switch work and pomp no prime did you resolve the problem in your bike?

@lifeiswarrecords5707 6 лет назад

Issue I’m having with my 2013 CBR600RR is while I’m riding my light get dim, then my check engine light comes on along with my HESD light. Bike won’t cut off at that moment but then my gear shift gauge that was added will be flashing a L and flashing the gears. After that the bike will then cut off and oil light will come on. It starts back up in 2 mins or less but it’s a dangerous thing to keep happen

@PartzillaParts 6 лет назад

Test stator, rectifier and wires. Voltage drops will cause this to happen, it's just a matter of figuring out where the issue is. Electrical issues like this can be a real bear.

@kevintieu693 5 лет назад

Hey for a 03 cbr600rr New battery in it. Intermittently slow cranking. Only once its warm. Slow crank and dies u can hear the starter go click click click really fast.

@PartzillaParts 5 лет назад

Well, just because it's new doesn't mean it's good. Do a load test on it.

@chiosaeteurn9790 5 лет назад

I rode my 05 cbr 600 rr yesterday on the highway and then it started jerking then it shuts off and on. What do you think is wrong ?

@PartzillaParts 5 лет назад

To little info to really tell. Could be fuel or spark.

@ricardomcdonald8239 5 лет назад

I have a 2006 Honda rr when I ride and the engine get hot and like 5 minutes after parking bike won't start and nothing is wrong with the starter and battery is good what can cause that problem

@PartzillaParts 5 лет назад

Regulator Rectifier. Test when hot to confirm.

@ricardomcdonald8239 5 лет назад

@@PartzillaParts please can you send of it looks like please am just getting into big bike

@ricardomcdonald8239 5 лет назад

The regulator rectifier

@sinvaocoi 7 лет назад

can anyone please help. I read the Voltage on the battery while press start button, it's 7.3V. then, I connect the multimeter to the starter it reads 5.2. Do I check all the ground cables from starter to the battery?

@PartzillaParts 7 лет назад

Hello Do it Diep. How many volts are you getting without pressing the start button?

@sinvaocoi 7 лет назад

Partzilla it was 12.6V

@PartzillaParts 7 лет назад

What you are describing to me would tell me that you need to replace your battery.

@malikhouser2825 6 лет назад

Trying to do my self don't have money to take to the shop

@dennisjimenez551 6 лет назад

I was riding and the bike hesitated then had no power, When U pulled over it would start fine but when I put it in gear and gave it gas it would die, then it would not turn over. After towing it home the fuel pump primes and the engine turns over but it does not start. could it be a bad battery?

@PartzillaParts 6 лет назад

It's more likely the rectifier. Try testing it and see what it looks like.

@paulmcdonald2888 6 лет назад

Hello I have a 01cbr600f1.won't start,new battery,Turning over, but can't hear the pump priming.any ideas where I could start looking.tried fuses,They seem ok.thanks.

@PartzillaParts 6 лет назад

I'll take that as a CBR600F4i? When you turn the key you should hear the pump prime. If not, make sure it's getting power. If power looks good, you may need to rebuild or get a new fuel pump.

@paulmcdonald2888 6 лет назад

Thanks for the reply.but do you think that it could be something else, before I go getting a new fuel pump.do they give trouble.

@PartzillaParts 6 лет назад

Fuel pumps go out. Especially if it sat for a long time or the tank is/was dirty and debris clogs up the works. Always test the electrical to the pump before you buy a new one. Search our videos, there are 3 Fuel Pump vids on a GSXR. The process will be essentially the same.

@Miniorpernik 5 лет назад

After a long winter iv decided to start it up.it turns over but it wouldn't start...I suspect the kill switch..my cbr is 2014..way to test the kill swirch?I heard the pump the first time I tried starting it..but then nothing..??!!??

@PartzillaParts 5 лет назад

you can test for spark. Otherwise it's almost always a fuel issue. Filter, lines, etc.

@antisignal734 4 года назад

Hi, I have a honda cbr600 2007 and its beeping twice the FI and when i drive it just stays on, any ideas what it might be ? Thanks alott

@antisignal734 4 года назад

Also, it starts beeping when i start the bike not when i turn on the ignition.

@PartzillaParts 4 года назад

I've never heard them beep...you mean blink? When you turn off the bike and turn it back on, it should blink a code. Check the service manual to see what it means.

@bevans2177 4 года назад

You might not get to this comment but i have a 2007 cbr600 and there has been a charging issue, I put it on the charger so i could take it to the shop and none of the lights turned on. I found this video and pulled out the same fuse that you did but mine was perfectly fine.. I even replaced it with the other one and still nothing lighting up on my dash. The only thing coming up is the clock and that's only when the bike is off, it's not on when I turn the bike on. Thanks and get back to me if you can

@bossylady80 3 года назад

A lil late, & u probably already resolved, but I had the same issue & it was a fuse. Had installed new LED turn signals & just needed to put in a stronger fuse cuz it kept blowing the fuses. Had to ride home with no speedo, etc. 1 day... good thing I was riding locally. Lol

@bevans2177 3 года назад

@@bossylady80 your good, just saw your reply but yes I did resolve it, my stator went bad which I think is common in 2007 cbrs, I had to replace the stator, regulator, and the battery because the battery stopped holding a charge