@@JenniferMaker Thanks! Ended up performing the power clean cycle. Waited over 12 hours (since I wasn't going to wake up at 2am to print). :) There are still come missing sections in the nozzle check page. But a huge improvement!! Black is black, cyan is finally printing again. And your sunflower has all the colors. Phew. However, when I selected "no" to question if all segments were printed correctly after the nozzle check print, and selected yes to a head cleaning cycle. It then showed the message for power cleaning and that it would take 11 minutes. I was like, back, no - where's the cancel? Finally clicked off. And it shut down. I am a bit scared to turn it back on.
I've had more issues with the Epson eco refill printer than regular ink jet. I'm so tempted to going back to the that and dealing with the high ink cost.
Here are some steps you can follow to address this issue: Print a Nozzle Check Sheet: Navigate to the home view on your printer and select maintenance, then select nozzle check. This will help you identify which colors are not printing correctly. Review the Nozzle Check Sheet: Look for any missing segments or faint lines in the cyan and magenta sections. If there are gaps or faint sections, it indicates a clog in those nozzles. Print a Purge Sheet: Download the printer purge sheets from JenniferMaker.com/588. There are specific sheets for each color (cyan, magenta, yellow, and black) and one for all four colors (CMYK). Open the appropriate purge sheet in Adobe Acrobat Reader and print it using the best quality settings. For your issue, you might want to start with the cyan and magenta purge sheets. Check the Printed Purge Sheet: Once printed, let the sheet dry and then inspect it closely. If the colors are consistent and solid, the purge sheet may have cleared the clog. If not, you may need to print additional purge sheets. Let the Printer Rest: If the purge sheets do not resolve the issue, let the printer rest for 12 to 24 hours and then try printing another nozzle check sheet. Avoid Printhead Cleaning if Possible: Try to avoid running printhead cleanings as they use a significant amount of ink. Only resort to this if the purge sheets and resting the printer do not resolve the issue.
I have an Epson Expression Ecotank ET-2750 Series and I am currently running the diagnostics on my printer to see if it could be clogged and so far I have run a nozzle check 3 times and cyan is the only color coming out. This printer has been sitting in storage where the ink might have dried in the tanks and the areas where it is supposed to come out. I didn't know about the purge sheets until watching this video and running a print head cleaning and getting no results so I had unfortunately ran a power cleaning on it. I am probably going to try the ink pad next after 12 hours are up to see if I need to replace that next or even flush the ink tanks. All are useful maintenance tips I have heard to hopefully fix the issues I am having with my printer.
I would recommend joining my sublimation FB group as there is such a wealth of information and troubleshooting in that amazing group! facebook.com/groups/sublimationmadeeasy
thank you for the videos on the clog. I have done every step and I still cant get my yellow or cyan to work. I tried to print and my printer is coloring orange items pink. oh I hope I get this figured out soon.
For more experiences and solutions from other crafters, please search and/or ask in my Sublimation FB Group, facebook.com/groups/sublimationmadeeasy ❤️
Hello Jennifer, great news, your method worked. Thank you. I did end up having to do a power clean, but it is printing all colors. However for the pass 2 days I have run into a printing problem. Now it is printing only half of the design. I have shut the printer off and let it rest for 24 hours and even reinstalled the printer. But I keep running into this problem. What can I do?
I'm glad to hear that the power cleaning helped with the colors. However, it's frustrating that you're now facing a new issue with your printer only printing half of the design. Here are a few steps you can try to resolve this problem: Check the Nozzle Check Sheet: Print a nozzle check sheet to see if any nozzles are clogged or if there are any missing segments. This will help you identify if the issue is related to the printhead. Print a Purge Sheet: If the nozzle check sheet shows any inconsistencies, print a purge sheet for the problematic color(s). This can help clear any remaining clogs. Ensure Ink Levels are Sufficient: Make sure that all ink reservoirs are above the minimum level. Low ink levels can cause printing issues. Clean the Print Heads: If the purge sheet doesn't resolve the issue, perform a printhead cleaning. This process can help clear any clogs that might be causing the problem. Check for Firmware Updates: Sometimes, updating the printer's firmware can resolve printing issues. Check if there are any available updates for your printer model. Inspect the Print Settings: Ensure that your print settings are correct. Sometimes, incorrect settings can cause partial prints. Make sure the design is set to print using color ink and that the best quality options are selected. Check the Paper and Print Area: Ensure that the paper is correctly loaded and that the print area is not obstructed. Sometimes, issues with paper alignment can cause partial prints. Run a Power Cleaning Cycle: As a last resort, you can run another power cleaning cycle. This is taxing on the printer, so only do this if the other steps don't resolve the issue. Feel free to. ask questions in the group for more feedback. facebook.com/groups/sublimationmadeeasy
Not sure you can really fix them after they are pressed but here is a tutorial that may help the process. jennifermaker.com/sublimation-color-problems/
Why are my nozzle check pages printing without missing segments but the words on the page have lines in them, the magenta has huge light lines in my designs, and the cyan dark lines? Now, I did the purge sheets and the magenta and cyan are better. The black purge was perfect and the designs are now fine BUT the words on the nozzle check sheet STILL have lines in them. I did a vertical AND horizontal print alignment too. Even the horizontal alignment had lines through it. So weird. So frustrating. I best not complain though, my designs are now fine, I just worry that it'll happen again because the lines in the words even though it didn't happen on the purge sheet. I'm baffled! Thank you for ANOTHER amazing tutorial, the purge sheets, and the gorgeous subliflower that I am totally putting on a shirt!
I'm glad all is well now anyway! You can always search and/or ask in my Sublimation FB Group too! There are so many helpful members and lots of helpful information, facebook.com/groups/sublimationmadeeasy ❤️
Where yours is coming out with the YMC colours, mine is only coming out with black when I do the maintenance check 🙃 any advice would be great appreciated ✨✨
It sounds like you're having trouble with your printer only printing in black during the maintenance check. Here are some steps you can follow to try and unclog the printer: Print a Nozzle Check Sheet: Navigate to the home view on your printer and select maintenance, then nozzle check. This will help you identify which colors are not printing correctly. Print a Purge Sheet: Open the purge sheet PDF for the color you want to fix (in your case, it might be cyan, magenta, and yellow). Print the purge sheet using the best quality settings available. This process helps push ink through the nozzles and can sometimes clear clogs. Printhead Cleaning: If the purge sheet doesn't resolve the issue, go back to the maintenance menu and select head cleaning. This process will push ink through the nozzles to try and clear any clogs. Be sure to check the ink levels before starting this process. Rest the Printer: If after three rounds of printhead cleanings the issue persists, turn the printer off and let it sit for 12 to 24 hours. Sometimes the ink needs time to settle. Power Cleaning (Last Resort): If the problem still isn't resolved, you can try a power cleaning cycle. This is a more intensive process and uses a lot of ink, so it should be your last resort. Check Ink Levels and Maintenance Box: Ensure that your ink reservoirs are filled past the minimum level and that the maintenance box isn't full. Running these processes with low ink can damage your printer or give unreliable results.
You can follow the same instructions for this and ask in the group if you need any additional help with that printer. facebook.com/groups/sublimationmadeeasy
Yes, the method for unclogging an Epson printer as described by JenniferMaker can also work for plain ink. The process involves steps like running printhead cleanings, printing purge sheets, and performing power cleanings, which are applicable to both sublimation ink and plain ink. The key is to ensure that the nozzles are clear and the ink can flow properly, regardless of the type of ink used. Just remember to follow the specific instructions for your printer model and keep an eye on the ink levels and paper supply.
My issue is that I've done the nozzle test and all of the blue is missing (the printer says there's no blue ink - there is, it's half full) When I ask it to clean the nozzles I get the message 'For proper operation of the printer select 'Reset Ink Level' to refill ink.' Pressing OK does nothing. So I guess the blue ink nozzle is clogged but there's no apparent way forward!! Any suggestions please?
It sounds like the blue nozzle might be clogged. Try running a deep clean cycle through the printer settings, and make sure the ink tank is seated properly. If that doesn't work, you could try resetting the ink levels manually in the maintenance menu. Also, double-check the ink cap for any clogs. If the issue persists, you might need to contact support for further troubleshooting.
Trying to do tumblers and shirts for a cruise we are going on in 5 days and my printer keeps printing with lines in my designs. I have ran clean head like 8 times and its not fixing it. Im so frustrated. Hoping I can get it fixed in time.
Can you recommend a no frills home printer. My Epson printer is clogged and I just wanna buy another one. Basic home use with photos. Copy, scan & print. No need fax.
This is what I found when googling your question. If your fax machine has a number-blocking feature. This feature usually requires a caller ID service. Select Settings on the printer's control panel. Select General Settings > Fax Settings > Basic Settings > Rejection Fax. Set the condition to block junk faxes.
It sounds like you might be experiencing a clog or an issue with the ink delivery system. Here are a few steps you can try to resolve the issue: Check the Ink Reservoirs: Ensure that the black ink reservoir is filled past the minimum level. Sometimes, if the ink level is too low, it can cause issues with ink flow. Turn Off and Rest: If you recently filled the tanks, try turning off the printer and letting it sit for 24 hours. This can sometimes help the ink settle and flow properly. Print a Nozzle Check Sheet: Navigate to the home view on your printer, select maintenance, and then choose the nozzle check option. This will help you determine if there are any clogs in the nozzles. Avoid Cleaning for Now: Initially, avoid selecting any cleaning options. Just gather information from the nozzle check sheet to see if there are any missing segments or faint lines in the black ink section. Check for Clogs: If the nozzle check sheet shows missing segments or faint lines, it indicates a clog. You can then proceed with a printhead cleaning process. Make sure your ink reservoirs are filled above the minimum level before starting this process. Printhead Cleaning: If necessary, navigate to the maintenance menu and select the printhead cleaning option. This process will push ink through the nozzles to clear any clogs. Power Cleaning as Last Resort: If the issue persists after multiple printhead cleanings, you may need to run a power cleaning cycle. This is a more intensive process and should be used as a last resort.
Hi there! I cannot for the life of me get the system dialogue box to open up. It will on my HP but now that i have a new computer a reloaded this 2850 Epson it will not open up so i can change the ICC profile manually. All i need is the dialogue box so I can make it mirror print. I am getting sooooo frustrated! It worked just fine before! UHG!
Here are a few steps you can try to resolve this issue: Check for Hidden Windows: Sometimes, the print dialogue box might appear behind other windows. Try minimizing or moving your open applications to see if the dialogue box is hidden. Update Printer Drivers: Ensure that you have the latest drivers for your Epson 2850 installed. You can download the latest drivers from the Epson website. Access Printer Settings Directly: Go to Control Panel > Devices and Printers. Right-click on your Epson 2850 printer and select Printing Preferences. Here, you should be able to access the settings you need, including the option to mirror print. Use a Different Application: Sometimes, the issue might be with the specific application you're using. Try printing from a different application to see if the dialogue box appears. Check for Software Conflicts: Ensure that no other software is interfering with the print dialogue box. Sometimes, security software or other utilities can cause conflicts. Reinstall Printer Software: Uninstall the printer software and drivers, then reinstall them. This can sometimes resolve issues with accessing printer settings. If none of these steps work, you might want to contact Epson support for further assistance. I hope this helps, and I understand how frustrating this can be! Feel free to ask in the group as well. facebook.com/groups/sublimationmadeeasy
Yes, it is possible that the ink has dried up, especially if you don't print often. Dried ink can clog the nozzles, which might be why your cyan, magenta, and yellow (CYM) barely print at all.
Take a look at this blog post, jennifermaker.com/sublimation-color-problems/ and see if it is helpful! If not, I would love for you to join and ask for help in my Sublimation FB Group, facebook.com/groups/sublimationmadeeasy
I have the F170 and it is printing blurry with off colors. I've done nozzle and power cleaning. I really think the ink is old and is needs to be purged
I didn't find your video until after I did 3 print head cleanings. because that is what I would do with my other printer to fix. Now I have printed your purge files and followed your steps. I am getting a notice to update me firmware. Should I update now? Will it make a difference. My printer is fairly new. My issue started with paper not feeding through properly and I canceled the print and started the print over and here I am in the mess. I have an et-2850
Given that your printer is fairly new and you're experiencing issues with paper feeding, updating the firmware could potentially help resolve the problem. Firmware updates often include fixes for known issues and improvements in performance.
Hello, I was wondering do I keep doing these steps if the colors are not working at all? The black works fine but the colors aren't working. The actual printer is brand new and I haven't used it in a while.
I'm not sure if you're using yours for Sublimation or for regular inkjet printing but I would recommend asking with as much detail and screenshots as possible in one of my FB Groups to see if others have experienced and what solutions they may offer! facebook.com/groups/cricutcraftersandmakers/ facebook.com/groups/sublimationmadeeasy
It can be a frustrating process. Here are some steps you can follow to try and resolve the issue: Print a Nozzle Check Sheet: This will help you confirm that the yellow ink is indeed clogged. If the yellow segments are missing or faded, proceed to the next steps. Print a Purge Sheet: Use a purge sheet specifically designed to clear clogs. You can find free purge files at JenniferMaker.com/588. Print the purge sheet to see if it helps clear the clog. Run a Printhead Cleaning: Navigate to the maintenance menu on your printer and select "Head Cleaning" (not "Power Cleaning"). This process will push ink through the nozzles to try and clear the clog. It may take about three minutes. Repeat the Process: If the nozzle check sheet still shows issues after the first cleaning, you can repeat the printhead cleaning up to three times. Make sure to print a nozzle check sheet after each cleaning to check for improvements. Let the Printer Rest: If the clog persists after three cleanings, turn off the printer and let it sit for 12 to 24 hours. This can sometimes help the ink settle and clear any air bubbles in the lines. Print Another Purge Sheet: After the rest period, print another purge sheet to see if the clog has cleared. Run a Power Cleaning (Last Resort): If the yellow ink is still clogged, you can run a power cleaning cycle. This is a more intensive process and should only be used as a last resort because it uses a significant amount of ink and can be taxing on your printer. Make sure your ink tanks are at least one-third full before starting this process. Check the Maintenance Box: Ensure that your printer's maintenance box is not full. If it is, you may need to replace it before you can continue printing.
😢 Omg I need serious help I placed the ink in which the Epson 2850 came with to do Sublimation on SkinnyTumblers Do I have to change the ink and how if the printer is full OH GEEEZZZZ HELP
We do not have any tutorials on changing the printer once inkjet ink is put in it. Remember it does void the warranty when sublimation ink is added so you may want to think about that if you try to empty out the ink to replace with sublimation ink.
Hi Jennifer, what do I do if my Cyan is the one not showing up and when I do purge sheets it’s printing magenta instead of cyan I’ve checked the ink levels and the cyan is full
Here is a tutorial that may offer some help. jennifermaker.com/sublimation-color-problems/ You can also ask in the group. facebook.com/groups/sublimationmadeeasy
Hi, I just want to ask, what will I do if my picture supposed to be should not have yellow background but when I start heating press it, it appears yellow background. . . 😢do you have any idea on what will I do? I'm so stressed thinking what to do. . . Thanks and more power.
I have an Epson ET-2850; was so frustrated and stressed trying to follow instructions to clear the clog; waited 24 hours and tried, after a few more prints I finally had success; so glad I stayed with it! Thank you for a very helpful video; couldn't have gotten thru it without you!
I am having this problem now. Hours and hours spent on trying to unclog the blue only. Replaced the maintenance box which led to the cost of resetting the printer and tons of ink and still can’t get the blue clear. Any suggestions? The printer is the ET-2803 and only a few months old.
@@JenniferMakershould I wait for 24 hrs before printing after setting up the printer and for test page should I used use sub 125 paper only to test subliflower
also why does it make a faint whistling noise when pulling paper into the machine I did a nozzle check no missing segments and also cleaned the print head still prints fine just having a hard time grabbing paper
Here are some steps you can follow to try and resolve the issue: Check Ink Levels: Ensure that the ink reservoirs for all colors (cyan, magenta, yellow, and black) are above the minimum level. Running cleaning processes with low ink can damage your printer or give unreliable results. Print a Nozzle Check Sheet: Navigate to the home view on your printer, select maintenance, and then choose the nozzle check option. This will help you identify which colors are not printing correctly. Print Purge Sheets: If the nozzle check sheet shows missing segments in colors other than black, print a purge sheet for the affected color(s). This process can help push ink through the nozzles and clear any clogs. You can find purge sheet PDFs online or create one yourself. Let the Printer Rest: If multiple cleanings and purge sheets don't resolve the issue, turn off the printer and let it sit for 12 to 24 hours. Sometimes, the ink needs time to settle. Run a Power Cleaning: As a last resort, you can run a power cleaning cycle. This process uses a significant amount of ink and can be taxing on your printer, but it might be necessary to clear stubborn clogs. Make sure your ink tanks are at least one-third full before starting this process. Check for Alignment Issues: If the lines on your nozzle check sheet are staggered, you might have an alignment issue. Refer to your printer's manual for steps to address this.
You can follow these general steps: Prepare Your Printer: Ensure that your ink reservoirs are filled past the minimum level. Load several sheets of plain copy paper into the printer. Manual Cleaning Process: Step 1: Turn off your printer and unplug it from the power source. Step 2: Open the printer cover to access the printhead. Step 3: Gently move the printhead to the center if it’s not already there. Step 4: Use a lint-free cloth or a paper towel dampened with distilled water or a specialized printhead cleaning solution to gently clean the printhead and the surrounding area. Be careful not to touch the nozzles directly. Printhead Soaking: Step 1: Place a folded paper towel soaked in distilled water or cleaning solution under the printhead. Step 2: Let the printhead sit on the soaked paper towel for a few hours or overnight. This can help dissolve dried ink clogs. Reassemble and Test: Step 1: Remove the paper towel and reassemble the printer. Step 2: Plug the printer back in and turn it on. Step 3: Print a nozzle check sheet to see if the clog has been cleared. Repeat if Necessary: If the nozzle check sheet still shows missing segments, you may need to repeat the manual cleaning process a few times.
ET-2800 printing blank pages only - I tried all options - factory rest, clean heads, clean alignment, clear data and settings, disconnected the power for 5 mins, kept in flat table - everything- I am sad
It sounds like you've already tried a lot of troubleshooting steps for your ET-2800 printer. Given the extensive measures you've taken, including factory reset, head cleaning, alignment, and more, it seems like the issue might be more complex. Here are a few additional steps you can consider: Check Ink Levels: Ensure that all ink reservoirs are filled past the minimum level. Running cleaning processes with low ink can damage the printer or give unreliable results. Maintenance Box: Verify if the maintenance box is full. If it is, you might need to replace it. A full maintenance box can prevent the printer from functioning correctly. Power Cleaning: As a last resort, you can try running a power cleaning cycle. This process uses a significant amount of ink and can be taxing on the printer, but it might help clear any stubborn clogs. Make sure your ink tanks are at least one-third full before starting this process. Firmware Update: Check if there is a firmware update available for your printer. Sometimes, updating the firmware can resolve underlying issues.
@@JenniferMaker thanks Jennifer for your response in spite of your busy schedule - I have power cleaned twice and what is strange is there is no drop in ink level after repeated power cleaning and head cleaning
@JenniferMaker - Maintenance box check - I am not clear what you mean by that but I will check. My luck is running out on all options and planning to return the machine and debating should I get eco tank 4800 or sawgrass - appreciate your thoughts
@@JenniferMaker finally the wait is over - thank you so much - I returned the ET-2800(sure that was a defective one) and bought ET-4800 and ta da … got the first print -subliflower
The black ink is grey? It could be temperature and or press time. Here is a tutorial. jennifermaker.com/sublimation-color-problems/ You can also ask in the group and show photos for help. facebook.com/groups/sublimationmadeeasy
You, my dear, have saved me a whole lot of trouble. I preach about how well your instructions are in your videos to my husband. But THIS video, has made a huge difference for me. I had all my print lines clogged so badly that only some black was coming through, nothing else. Now here it is day 3, and I have a minor clog in the black line only. But the rest of the colors are perfect. Thank you so much
It sounds like your printer might be experiencing an issue with ink delivery from the bottles to the printhead. Here are a few steps you can follow to troubleshoot and potentially resolve this issue: 1. Check Ink Levels: Ensure that the ink reservoirs are filled past the minimum level. If they are too low, the printer might not be able to draw ink properly. 2. Nozzle Check: Navigate to the home view on your printer, then select maintenance and perform a nozzle check. This will help you determine if there are any clogs in the nozzles. 3. Printhead Cleaning: If the nozzle check shows missing segments, perform a printhead cleaning. This process pushes ink through the nozzles to clear any clogs. Remember, this process uses a significant amount of ink, so make sure your ink levels are sufficient. 4. Rest the Printer: If you recently filled the ink tanks, turn off the printer and let it sit for 24 hours. Sometimes, the ink needs time to settle into the tanks properly. 5. Check for Air in the Lines: Sometimes, air bubbles can get trapped in the ink lines, preventing proper ink flow. Letting the printer rest can help resolve this issue. 6. Power Cleaning: As a last resort, you can run a power cleaning cycle. This is a more intensive cleaning process that uses a lot of ink but can sometimes clear stubborn clogs.
Hi! I started a small retail business and need a printer 🖨 basically for a very small amount of printing (invoices, small printouts, etc) which printer would you suggest?
This is BY FAR THE BEST video on the topic!!! I watched so many before I found this and everything was so clear and explained BEAUTIFULLY!!! Thank you for your hard work on this!!
I just wanted to stop back here and thank you! It took 4 days, but I was able to unclog my Epson 2850. While the purge sheets never showed any color except gray, I performed nozzle checks, print head cleaning, and a total of 2 power cleanings that finally did the trick. Each day after I tried an assortment of actions, I shut the printer off for at least 24 hours. Gradually, the nozzle checks showed a tiny bit of blue (the original missing color), but when I would then do a print head cleaning, the blue would disappear in the next nozzle check. Finally, today I turned the printer on, did a nozzle check and a print head cleaning, and all colors came out perfectly ... plus a big blob of black ink was expelled onto the upper right corner of the paper. I was really worried I was going to need to buy another printer, so thanks again for calmly explaining that unclogging could take a lot of time and patience. An Asurion insurance plan was purchased for this by my brother as a gift, but I figured that any claim would be rejected since I was using Hippoo ink. BTW, the printer sat all winter unused in subzero temps (down to -40F) in my unheated house while I was away, and it started up immediately and worked flawlessly from mid-March to mid-June. I have used it almost every other day since, so who knows why it suddenly decided to clog!
I have the same problem. All my colors do not print. When I do the nozzle test, I got nothing from the colored Inks. I’ve done multiple purge pages and no color were printed. What can I do next?
thank you so much. i peinr a subliflower but, I want to know how can I fix a cyan color who print similar to green instead light blu ? and a pink (color of skin) is print so much yellow/brown ..... i know there is a problem with yellow but i can't fix it !!! i will be happy if you can help me to do something. thank you for your help
Here are some steps you can follow to address the cyan and pink color problems: 1. **Print a Nozzle Check Sheet**: - Start by printing a nozzle check sheet to identify if there are any clogs or issues with the cyan and magenta nozzles. This will help you see if the colors are printing correctly or if there are missing segments. 2. **Print a Purge Sheet**: - If the nozzle check sheet shows issues with cyan or magenta, print a purge sheet for those colors. You can download the purge sheets from JenniferMaker.com (design number 588) . Use Adobe Acrobat Reader to print the purge sheets for cyan and magenta. 3. **Inspect the Purge Sheet**: - Once the purge sheet is printed and dried, inspect it closely. If the cyan color is still printing greenish or the pink color has too much yellow/brown, it indicates that the clogs might still be present. 4. **Repeat the Purge Process**: - If the colors are not consistent, print another purge sheet for the affected colors. You can repeat this process up to five times to see if the clog improves. 5. **Let the Printer Rest**: - If the issue persists, let the printer rest for 12 to 24 hours. Sometimes, the ink needs to settle, or there may be air in the lines that will come out with some rest. 6. **Clean the Printer Nozzles and Print Heads**: - If resting the printer doesn't help, proceed to clean the printer nozzles and print heads. This step can help clear any remaining clogs. 7. **Check for Ink Contamination**: - Ensure that the ink tanks are filled correctly and that there is no contamination between colors. Sometimes, incorrect filling or mixing of inks can cause color issues. 8. **Run a Power Cleaning (Last Resort)**: - If all else fails, run a power cleaning cycle. This is a more intensive process and uses a significant amount of ink, but it can help clear stubborn clogs. jennifermaker.com/sublimation-color-problems/
Yes, depending on your printer and the situation, you may be prompted to update the machine's firmware during the maintenance process. It's generally a good idea to allow these updates as they can improve the printer's performance and fix any existing issues. Just make sure to follow the prompts on the screen and ensure your printer stays on during the update.
I have a epson et15000 that converted for sublimation. My printer goes thru the motions of printing but there is zero ink that gets put on the paper…Help!!
Here are some basic steps you can follow to troubleshoot and potentially resolve the problem: Check Ink Levels: Ensure that your ink reservoirs are filled past the minimum level. Low ink levels can cause printing issues. Nozzle Check: Perform a nozzle check to see if any of the nozzles are clogged. Navigate to the home view on your printer, select maintenance, and then choose the nozzle check option. Print a nozzle check sheet and examine it for any gaps or missing segments in the lines. Purge Sheets: If the nozzle check indicates clogs, print purge sheets for the affected colors. Open the purge sheet PDF for the color you want to fix and print it using the best quality settings. Label the printed sheet and check for consistency. Repeat this process up to five times if necessary. Rest the Printer: If you recently filled your tanks, turn off the printer and let it sit for 24 hours. Sometimes, air bubbles in the ink lines can cause issues, and resting the printer can help settle the ink. Clean the Print Heads: If the purge sheets do not resolve the issue, you may need to clean the printer nozzles and print heads. This should be done as a last resort because it uses more ink. Check for Air in the Lines: Ensure there is no air trapped in the ink delivery lines. Air bubbles can prevent ink from reaching the print heads.
I bought my Epson ET- 2720 printer right before covid -19 struck. I put in the tank colors, and made 2 color tests, and that was 2019, and I haven’t had a chance till now (September 2024) to use my printer. I fear that the ink inside the printer has dried out completely. Not sure what to do next.
Hello! It sounds like your cyan (blue) ink might be clogged. Since you mentioned that the purge sheet printed all yellow and the blue ink is full but hasn't been used in a few months, here's what you can do: 1. **Print a Nozzle Check Sheet**: This will help you confirm if the cyan nozzles are clogged. Navigate to the home view on your printer, select maintenance, and then choose the nozzle check option. Print the sheet and check if the cyan section has missing or faint lines. 2. **Print a Purge Sheet**: Since the cyan ink is not working, print a cyan purge sheet. You can download the purge sheets from JenniferMaker.com/588. Use Adobe Acrobat Reader to open and print the cyan purge sheet. Make sure to use the best quality settings available. 3. **Repeat the Purge Process**: If the first cyan purge sheet doesn't improve the print quality, print up to five more cyan purge sheets. This process helps push ink through the nozzles and can clear clogs. 4. **Let the Printer Rest**: If the cyan ink still isn't working after printing multiple purge sheets, let the printer rest for 12 to 24 hours. Sometimes, this can help the ink flow better. 5. **Print Another Nozzle Check Sheet**: After the rest period, print another nozzle check sheet to see if there are any improvements. If these steps don't resolve the issue, you might need to perform a printhead cleaning. However, keep in mind that this process uses a significant amount of ink. Only proceed with printhead cleaning if the purge sheets and rest period don't work. I hope this helps!
Thank you! After three days of intermittent printer cleaning, on day three I used your purge sheets, more cleaning, and finally the yellow and blue ink started working again!! :)
Oh my gosh! Your purge sheets are genius! They make so much sense. I only wish I'd found this video years ago and saved myself some ink. But now I'll be starting with those first if one of my colors isn't working. One print and boom it had cleared the clog. After I wasted ink on three print head cleanings. Not doing that again if I don't have to.
why would my Cricut design space document not print on the right position on my epson eco tank it's printing near top of page not showing the whole image
Excellent video - super helpful! Thank you so much for sharing your PDFs and being so thorough. Really appreciate it. I was able to get my printer working again with a power clean :)
It sounds like your yellow purge sheet is not printing correctly and is coming out a dark greenish brown, which indicates that there might be a mix-up or contamination in the ink lines. Here are some steps you can follow to troubleshoot this issue: Check Ink Levels and Colors: Ensure that the yellow ink tank is filled with the correct yellow ink and that there is no contamination from other colors. Sometimes, ink from other colors can mix if the tanks are not properly sealed or if there is a leak. Print a Nozzle Check Sheet: Go to your printer's maintenance menu and print a nozzle check sheet. This will help you identify if the yellow ink is being mixed with other colors. Look for any inconsistencies or color mixing in the yellow section. Clean the Print Heads: If the nozzle check sheet shows that the yellow ink is contaminated, you may need to clean the print heads. Follow the steps in your printer's manual to perform a print head cleaning. This process will help clear any mixed or clogged ink from the nozzles. Print Another Yellow Purge Sheet: After cleaning the print heads, print another yellow purge sheet to see if the issue is resolved. If the yellow color still appears incorrect, you may need to repeat the cleaning process. Let the Printer Rest: If the problem persists, turn off the printer and let it rest for 12 to 24 hours. Sometimes, allowing the ink to settle can help resolve color mixing issues. Check for Air in the Lines: Ensure there is no air trapped in the ink lines, as this can cause color mixing. If you suspect air in the lines, follow your printer's manual for steps to remove it.
Jennifer i have a problem, first my magenta wasn't printing and then printed out your purge sheet and it worked, BUT for some reason now the cyan won't print.. and when i purged with your sheet for cyan, it shows light pink... what do i do now
Great video thankyou, im going to invest in a new Epson eco tank 2860 tomorrow for my printing venture, I’ve heard the only bad thing about them is blocked heads, this vid has given me enough confidence to know I can unclog it with ease 👍🏻👍🏻🙂
Thank you, I tried the clean head twice and nozzle check, then again the next day, and to my great, great surprise, I started to see a noticeable improvement with the nozzle check, and then printed the "purge" page successfully, and did NOT have to use the "power head clean !"
This video was really helpful. Thank you, I managed to fix my printer with just the purge files. However, I noticed that printouts are a little bluish. So, I guess the job is not completely done.
Oh my i run cleaning cycles pretty often and never knew about the maintenance box or that it’s been storing ink in there after every time yikes! Thanks for the video!
Jennifer, thanks for your help. My problem was just cyan. It was printing out the purge in a pinkish color in the beginning of doing all this. I did a cycle of 3-5 purge and 2 head cleanings. I repeated this cycle, every once in a while mixing up a little differently with maybe 6 purges in a row, with two cleanings, and once I did 3 purges followed by 3 cleanings in row. I also threw in a few purges with all four colors. Probably did these cycles 8-10 times and I figured I would eventually leave it alone and see if the 12-24 hour wait would help because I was still only seeing solid pink. Actually was feeling that I would likely end up needing to do the dreaded power cleaning. Continued on though and FINALLY I saw a few jacked up blue streaks on the upper portion of the color block so I kept going. Eventually after a few more cycles, on of the nozzle checks after doing a cleaning showed cyan with maybe just about 15% breaks in the lines! Kept going and now the ink seems to be completely flowing. There is still one issue... I am still working on it, but as of now I can't seem to completely shake these extremely faint darker blue lines running across the cyan color block. I only see them when printing in standard, but they are not there when using the high setting... on high it looks 100% solid and beautiful. Judging from what I have said, would you say my problem is no longer a clog or air in the lines so doing a 24 hour wait wouldn't really help at this point... and what my issue is now is solely with continuing to clean the print heads? I like the look of high better anyway but would rather not HAVE to print in high for everything. Btw, I do not use sublimation ink whether or not that has anything to do with anything and the files you provided, I just used the standard ink that came with the ET-15000
It seems the issue is related to the print settings rather than a physical clog. Check Print Quality Settings: Ensure that your print quality settings are optimized even when using the standard mode. Sometimes, adjusting the settings within the standard mode can help improve the output. Update Printer Drivers: Make sure your printer drivers are up to date. Sometimes, outdated drivers can cause print quality issues. Alignment Check: Perform a print head alignment. Misalignment can sometimes cause lines or streaks in prints, especially in lower quality settings. Paper Quality: Ensure you are using the correct type of paper for your printer. Different papers can affect print quality, especially in different print modes. Maintenance: Even though you mentioned not wanting to do more print head cleanings, it might be worth doing one more round of cleaning to ensure everything is in top shape. Since you mentioned that you do not use sublimation ink and are using the standard ink that came with the ET-15000, this should not be a major factor in your issue. However, always ensure that the ink you are using is compatible with your printer. Using the high-quality setting will provide the best results in printing when you need it.
@@JenniferMaker Ok thanks. I think the issue is the quality of paper(just basic copy paper I'm using during testing) when combined with the standard setting. Results rage from good to great looking when using a combination of either of the matte paper options with high setting.Even when I choose one of the matte options with standard it comes out without banding. If I continue to use regular printer paper(not matte), but choose one of the matte options in the dropdown list and also choose matte paper option on the actual printer settings, is there any negative effect on the printer heads or is it just that the printer is dumping more ink out onto the page and it doesn't really mater if you are lying to the printer that it is using matte paper? Also, I have heard that updating the Epson can cause issues with performance and third party products. It might just be with updating the actual firmware though, not if you only update the drivers if you are even allowed to do those separately when updating. Not even sure if the 3rd party thing effect Ecotank owners unless for some reason you wanted to replace the tanks and they have chips. Do you know anything about issues when updating, especially for the ET-15000?
Very helpful video, thank you very much 🤩 I'm off to try your purge sheets now and great tip about printing every week in colour (I've not been doing that and get frequent clogs). Fingers crossed your tips will solve my issues lol 😅💖
Thank you so much I had no knowledge about even owning a inkjet printer came across this video my ink wouldn’t even print no color just grey did 2 days of what she suggested and my printer works and now I know about my printer 😊I have the Epson 2850
THANK YOU, THANK YOU, THANK YOU. I had left both my printer sitting for too long and it was not printing cyan on one and the black on the other at all now they are both back working after many cycles of purging, nozzle cleaning and head cleaning.
The 2720 is a work horse. I've had it for over 7 years. Got it before my mom passed. Haven't printed in color for a few weeks so yellow stopped working. Glad I saw this. I've tried everything, including power cleaning, but haven't checked the print since doing it yesterday. I wish I had known about a purge print first. Wish me luck.
Thank you SO MUCH for this tutorial! For some reason my yellow was not printing, but all other colors were. I don't think I had a clogged line because I changed one setting in my printer settings and all of a sudden the yellow started printing! I am saving this video for future reference because it is SO VERY INFORMATIVE AND HELPFUL!!!! Thank you for taking the time to do this.
and even after following this video on 2 different epson 2720 and 2800, my nozzel checks where still horrible but someone told me to change print settings to high quality and photo paper ink - and omg my prints no longer have lines thru them... what a difference. and now i know i need to get a new maintenance box for my 2720 and i'm close on the 2800 so i ordered them. thank you so much for your video.!!!
Oh my goodness thanks. I had a very challenging week last week and to top it off, you guessed it my printer clogged. I searched how to fix it and did eventually do a power clean after a few steps and 12 hour waits. I would have loved to have tried the purge sheets and now I have them as a fabulous resource. Lesson learned. I have something I print weekly and have missed it maybe 2 times this is so helpful. Printing weekly is a must you are so right. 😂
Thank you! Thank you! My blue was completely clogged. I followed all your instructions and had to do a full clean, but I'm back to having fun with sublimation today!
Jennifer you are a legend! I watched several videos and followed them and then your video really stood out. I did the nozzle clean and head clean and unfortunately i had to do the 11min power wash. I went online and got my password from your site and went to your library and ran the file 588 for your PDF files for the Purge Sheets. I waited 12 hours overnight, got up this morning and ran the YELLOW Purge sheet and CMYB Purge Sheets! .......and its FIXED!! Yipee. I was sceptical at first about letting your printer 'rest' as i have never heard of that and this was also my first time to have a problem with our ecotank (we have ET-2820 her in Australia) Our problem was that last week after the kids printed an A4 page of a copy of a photo that the Yellow and Cian were not coming through in colour printing. It was for of all pinky looking. I ended up doing 5 x head cleans and only 1 power wash. It took a 3rd of my ink whilst doing that so now i can see via the process that you dont want to do that very much and it would be much better to run a purge weekly than go through all this again. A big thank you for your expertise.!!!!
Sublimation can be pretty fun to see the projects come together, but it is truly heart breaking to deal with a clog. I let my printer sit for months and every time I kick my self in the but. Thank you for reminding me to print weekly
@@JenniferMaker Yes after letting my printer rest for 24 hours. and cleaning the nozzles one more time and using you subliflower, the colors finally broke through. I also placed a timer on my phone to remind me. I thought my printer was over. Thank you, 🥰
Thanks Jennifer! I can't wait to try this when I get home. I'm praying this works! I have the Epson 2800 so I can follow your instructions exactly! Definitely downloading your print sheets! I've been using the subliflower to check. What a great color check tool!
