Thank you for watching! Please like and share if you enjoy. If you like this video, please visit our channel to view our other videos and subscribe for updates.
Just buy-it and I figured was something wrong with charging... so I look on you tube and I found your video. My boy is happy now for his birthday.Thanks man. The battery was different but I sorted how to fix-it. You’re the man.
Best video on battery advice on the hole of RU-vid, I have not be able to charge my battery and have been up the fucking wall because I paid good money for these batteries, you have just fixed my problem in 5 minutes, thankyou very much you cleaver man , jfk over and out
Mine is different too and I tried charging in several pads but didnt keep it very long in each pad. Is there any issue if I kept that in each pad for too long? My battery wasnt charged for many months and might have lost the voltage completely. Any tip will be helpful.
Could have explained that you were connecting the negative to the spot marked B- on the board, for those that have a different one, but thanks a million, saved my step daughters hover board! Or at least saved me $60+ buying another battery.
Good this works, thanks for the information, I changed two of the batteries because they had corroded but still wouldn't charge all problems solved now and link removed.
you are a life saver. I think I ended up shorting several different spots on my board before it worked, but in the end... IT worked!!! Thank you So much!! Dunno if you still make videos or not, but you got a subscribe from me for saving me $100. Thanks again!
Thankyou for taking the time, after 3 months of no use my 'zinc smart gt' only has lights on the board if i have charger plugged in, it will recalibrate but still no movement in board, i take ''green light' charger out and everything dead again, no lights no beeps. So hopefully i can kick start the battery from inside or verify that its dead forever. I have multimeter but have never used one. Now i will open board up & try. My boy would be so happy. .... EDIT.....My battery pack is different, is he putting one wire on negative and other end to a positive? or neg to neg? wire sparks and heats up but no change, BATTERY reading at 12, charger still green light. Charger isn't faulty.
What should i do my board i switch on charge e board during charge is flashing amber and power is indicate red light but within 3hr power indicate light turn green but board still amber flash for about 2~3hrs... auto shut down. After i plug out switch 🔛 everything connect well on green light but when I wanna ride another side flash red with peep sounds i try it few times but charge within 3hrs done yet after 1st time charge i can't even used already
I know it's been 4 years but I recently just got this issue with my hoverboard and after watching several videos your video was the most helpful and simple way to fix👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽 thank you after jumping it its now charging 😁✌🏽👍🏽
Good stuff, my battery was at 6 volts and wouldn't charge, had to short it out a few times but it finally started charging. It's now at 25 volts and climbing. Thanks
@@MrJOLLYRANCHER92 I completely disassembled all the battery, wiring all, kept photos how qnd where all connected and a layout, salvaged few dead ones and replaced a few, and soldered all back together with copper wire, Taped the whole thing, still works to this day, I know its a lot of work but it was worth it for me
My battery wouldn't charge because it was just a litter undervoltage. Battery light red and only beeping. But here is a tip: when you remove the gyro cable (next to the led cable) on one side the battery charges. When it gets to 36v then the gyro cable can be attached again. That only works if no cell has failed, but you can try it (just be around the first charges, in case anything goes wrong).
My brand new hoverboard run time is around 25 minutes then it cut off power of board. At full charge it was around 41.5 V and after 25 minutes the battery voltage was only 37.8 V for cut off. Why is the voltage still so high and already there was a cut off the power? At wat voltage should the board switch off? Any suggestions?
My battery is different. But when i try this method i just big sparks. Its a different layout. Have you got social media i can contact you and forward a picture
Bro i don’t have the voltmeter? Is it that i have tk connect the wire with voltmeter and then with the black wire or we just have to get a wire and connect it with the black wire? Plz reply i’m rly confused
Hi, My battery is showing 41.2v but hoverboard still won't work. Does that mean the BMS is at fault? Is there a way to fix the bms or do I have to buy a battery? thanks