How To Install A Muzzle Device With A Crush Washer

Подписаться 1,9 тыс.

Просмотров 97 тыс.

50% 1

I installed a birdcage A2 flash hider on an AR-15 rifle using a crush washer.
Muzzle Device Install Guide
neckbonearmory.com/muzzle-dev...
Muzzle Device Types:
neckbonearmory.com/MuzzleDevices
Cleaning Gear I Use:
neckbonearmory.com/cleaning
-------------------------------------------------------------------------
Music: www.bensound.com
Disclaimer: These videos are strictly for educational and entertainment purposes only. Imitation or the use of anything demonstrated in my videos is done AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state and federal rules apply to such. We (including RU-vid) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any our videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun shop and DO NOT sell or deal in Firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify us immediately. By viewing or flagging this video you are acknowledging the above.
Fair Use: In the rare instance I include someone else’s footage it is covered in Fair Use for Documentary and Educational purposes with intention of driving commentary and allowing freedom of speech.

Развлечения

Опубликовано:

21 мар 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 80

@gjmarkjesse1324 2 месяца назад

Always love these kinds of videos. Explaining why things need to be the way they are and straight into the installation. Compared to other videos where a simple subject like this will be turned into a 45 minute video with only 2 minutes being about the actual subject.

@guardiangibbs2663 Год назад

Thank you for the tip. I also learned, I should probably have a couple spare crush washers.

@hungpham-pm5hk 12 дней назад

P1pppooĺ❤

@bradlyons5773 2 года назад

Thanks mate. informative, straight to the point and no BS.

@skoopsro7656 2 года назад

as much as it sucks for him.. its great for us. FUCK monetization.

@DLN-ix6vf 3 года назад

thanks ; that really helped me ! quick concise and to the point in less than 4 min. other U-Tubers please take note !

@AfterGlow2188 2 года назад

Exactly! This was everything I needed to know without having to hear what OP had for lunch.

@texassportsman5880 2 года назад

I used your method to the letter to install and time the extended A2 flash hider on my AR. Looks better than factory install.

@d30gaijin 2 года назад

Thank you for this video! Very clear and concise.

@rextownsend5296 3 года назад

Definitely helped. Thanks for the great tutorial 👍🏾💯

@jamesmadison9244 Год назад

Thank you for the advice had a bad experience before and ended up using shims. Had to go an entire revolution before I could time a compensator to an AR9 barrel. The precrushing did the trick!

@dannyteichroeb864 10 месяцев назад

Thanks for the easy to follow clear instructions, got my muzzle brake installed!

@craiglewis6821 8 месяцев назад

Great video!! I was confused about which way the crush washer went. Very clear instructions.

@Infinite.phases 6 месяцев назад

Thank you for taking the time to make this video. Helped a lot.

@Alop777 Год назад

Short and informative. That's what I'm talking about! Thanks, I subscribed.

@jeffheyer7783 Месяц назад

I’m an engineer.. great video. Easy to follow with the information I need

@jdp1956 24 дня назад

Thank you for this video, Very clear and to the point.

@bobatbilletcreations 2 года назад

Thanks for sharing, Very helpful!

@airdrop1670 2 года назад

The info I was looking for , thanks .

@stuartlunsford7556 3 месяца назад

Perfect! My muzzle brake has a very small mounting surface, so I wondered if I should flip the washer. Answered that quick lol!

@thannydevitos2332 Год назад

Thanks brother. Good video. I’m used to my AK where it has the dimple in the muzzle device to lock

@ratagris21 Год назад

Yes it's easier to do. Unless those who make ARs think all muzzle devices take a crush washer including AKs - not.

@Nobody-sp9xj 3 года назад

Great vid dude, thanks

@MiguelHernandez-ql8ke 2 года назад

Thanks couldn’t figure it out 👍🏽

@tonysmith5465 3 года назад

Very well done friend. Thanks a lot. Good video. SC Navy vet.

@ALRIHAE 4 дня назад

Thanks neckbone!

@wojciech_migda Год назад

Perfectly spent 4:08 minutes :-). Thank you!

@vince4984 9 месяцев назад

Thank you for making a short video. I hate long instruction video's.

@hoplite22 3 года назад

Helpful thanks

@johnharris-pn5vy 3 года назад

Great video

@lobster8009 4 месяца назад

You dont need to get a brand new crush washer every time you take your A2 birdcage off. As long as it gets a reasonable amount of tourqe going back on its just fine as it is not under huge stress in normal operation. Might be differend on other devices and if you use a suppressor that mounts to the A2 id recomment replacing the washer every time. But just the A2 alone is never coming off because you didnt replace the washer.

@boomerrumor8252 2 года назад

Good job

@Drylogic_kills 15 дней назад

And what happens when your barrel extension de torques? Geissle make a reaction rod that prevents that

@davidsongheng5967 Год назад

Correct info on the crush washer install process, but missed the very important thing, the use of a Reaction Bar. Upper Receiver Vise Blocks are only good for small and non-torque related install work on the upper. For any torque related work involving the barrel, I highly recommend using a Reaction Bar. This would help you avoid damaging the vise block, or worst, cracking your upper receiver. Use a Reaction Bar any time you apply torque to the barrel. This includes tightening the Barrel Nut, and timing and clocking muzzle devices.

@BertReno Год назад

Where can I get one? I want to install my muzzle device on my hunting rifle the correct and safe way. Please provide a link

@davidsongheng5967 Год назад

@@BertReno Reaction Bars are only good for AR type semi-auto rifles, which have splined extensions on the barrels. These reaction bars have splines that fits right in the AR type barrel extensions. My comments was for the AR rifle build that this shown. Unless you hunt with an AR type rifle, then my comments would apply. You can get them from Brownells, MidwayUSA, etc. or any online retailers. For bolt action type hunting rifles, browning or MidwayUSA also have plenty of choices for barrel blocks that you can use. You do not need to apply a lot of torque on these muzzle brakes. Just snug tight is usually what's needed. The crush washer will not allow you to over torque. If you need to clock your muzzle brake straight and plumb, then you have to add some muzzle thread shims correct the timing. Hope this helps.

@xiZm 11 дней назад

Tighten, loosen, tighten, loosen, tighten until you’re about a quarter to half turn

@fimfengius 4 месяца назад

Best!

@Drylogic_kills 15 дней назад

Btw, I’ve seen index pin break off.

@TheSouthpawSharpshooter 3 года назад

I might subscribe. I don’t know though. Lol thanks for vid.

@stevesmith756 Год назад

Who taught these guys that “pre-crushing” a crush washer is correct. Crush washers are a one time event. Once you crush it don’t back it off

@jklop7841 Год назад

He'll be fine. Don't cry.

@andrew_xj8411 8 месяцев назад

For traditional crush washers, yes. For this specific application they are designed to be backed off then retightened.

@adamhearts9195 Год назад

my barrel tip has a spring/pin and indentation on the break for correct alignment. it did come with a crush washer though,, vg6 epsilon ak. My m70 has the spring on the barrel though, do I need to use the crush washer or just screw it until it's tight and factory aligned. I guess the crush washer is to be used for barrels that don't have the spring pin to keep it in place.? Thank you

@Mike_Richardson_1955 2 года назад

What is that device you connected to your weapon to put in to the vise? And where did you buy it?? Great video!!!!!

@NeckboneArmory 2 года назад

Thanks, it's an upper vice block. I got it here: shareasale.com/r.cfm?b=15098&u=2698398&m=4355&urllink=www%2Eopticsplanet%2Ecom%2Fobsidian%2Darms%2Dar%2D15%2Dupper%2Dreceiver%2Dvice%2Dblock%2Ehtml&afftrack=

@VincitOmniaVeritas7 11 месяцев назад

Do you recommend using grease like molibidenium on the muzzle threads?

@trevordane4466 2 года назад

My muzzle break needs to turn a 3/4 turn to be facing the right way. Will that be too much stress on the crush washer?

@jpogigtxcr1778 3 года назад

Brief and concise! Now, do I need rockset or red loctite with a crush washer?

@NeckboneArmory 3 года назад

I wouldn't use either. The crush washer should be all you need.

@SkillCollectors 3 года назад

VG6 brakes actually come with anti-seize.

@twiggybones7040 3 года назад

Rockset is not a bad idea. If you wanted to remove the muzzle device soak it in water and it'll neutralize the rockset.

@emperormayham2596 11 месяцев назад

is this supposed to be tight to the barrel or loose, i have one for a 9mm pistol but the washer sits very loose and has nothing to push against till i get to the front of the weapon which i couldn't tread the muzzle break enough for

@ifc3893 4 месяца назад

Crush washer cone forward or backwards?

@tonimoon6346 2 года назад

🤘

@brandonoswald9828 3 года назад

What vice block is that?

@DuyNguyen-et4tv 3 месяца назад

Where can I buy that wrench?

@aquaticlives2948 Месяц назад

Idk if i did it correct or not but whem you said "do a 25% turn" i went ahead and did a whole full turn and stopped where when it was aligned. So basically i hand tightened then i grabbed my wrench and went a whole full turn not just the 25 you said, is that okay?

@asdfgoogle Год назад

Huh? Concave facing the muzzle device. Okay. Easy. And the small side facing the shooter.... Wait.... But I thought the concave side....

@chrisross1657 Год назад

Good tutorial but shims are the way to go. ✌✌

@CC-hx2pv 2 года назад

Is the crush washer necessary to install? What happens if you don’t put it on? Do all compensators need the crush washer ? I have one compensator that came with it and one that didn’t. Thanks for info in advance.

@NeckboneArmory 2 года назад

You don't need crush washer. You can use shims, lock nut, or nothing at all if you'd like. The crush washer just keeps it from loosening.

@CC-hx2pv 2 года назад

@@NeckboneArmory thanks for that. So it’s basically just an extra security feature. Less likely to get loose with crush washer? Just subscribed to your channel. I’ll be checking videos out.

@kanejakejimmy Год назад

Well shit... I've been placing those damn crush washers on backwards for 20 years.

@nenadg3665 5 месяцев назад

Everything is ok except vise. You're clamping upper receiver but not the barrel itself. You can damage barrel bed on upper receiver. You need action rod or what people use to call them.

@Spencer900 5 месяцев назад

How will you know it’s damaged?

@nenadg3665 5 месяцев назад

@@Spencer900 Can't really say but you're applying torque to part 1 and have clamped part 2. The connection between those parts has to take torque force and you only want it on muzzle. Maybe barrel notch on upper receiver can be widen?

@BearArmsChannel Год назад

Do i need a crush if my flash doesn't need to be timed?

@NeckboneArmory Год назад

nope, can use shims or nothing but torque it down right.

@matthewflesch8290 3 года назад

Don’t you need a torque wrench to ensure you don’t over tighten it? I’m pretty sure that wrench you were using isn’t a torque wrench.

@NeckboneArmory 3 года назад

That wrench was just a simple armorers wrench. As long as you tighten past hand tight more than a quarter turn, it will be torqued correctly with a crush washer. You can't really over tighten with a crush washer unless you completely flatten the crush washer. You shouldn't need to tighten it to that point. Even on muzzle devices that need to be timed, you will never need to do more than one full rotation to get it timed properly. Keep an eye on the crush washer, if you're flattening it, you're going too tight. If you want to use a torque wrench for peace of mind, that works too.

@VinnieChenzo Год назад

@@NeckboneArmory is one whole turn to much? When i hand tighten mine it is at a perfect time. I will have to go all the way around again.

@scottwothe3781 Год назад

Do you use any Loctite with a Crush Washer?

@NeckboneArmory Год назад

no I dont

@yoshiike1 2 года назад

600

@chadknapp2437 Год назад

If this video helped you maybe subscribe.. idk 😂😂😂

@khann844 Год назад

I have no idea what you did cause you cut the video

@earlyblackmz Год назад

👍

@brandonvictor9388 3 года назад

My barrel is tapered at the end will tightening the crush washer damage the barrel? Stainless steel barrel BTW.

@NeckboneArmory 3 года назад

It should be fine. only really need 20 - 30 ft lbs on the crush washer. The only problem I've seen with tapered barrels and crush washers is that the crush washer needs a shelf to crush against and some tapered barrels lose that. I've seen people flip the crush washer around because of it.