How to install an Adjustable Door Threshold Sill (Complete Guide)

Подписаться 11 тыс.

Просмотров 478 тыс.

50% 1

Learn how to replace your adjustable door threshold sill for an exterior inswing door in just minutes!
The Tools: 00:26
*Adjustable Door Threshold - amzn.to/3o1WxkY
*Rigid Multitool - amzn.to/3f3caVh
*Rigid Sawsall - amzn.to/32JIp6q
*Rigid Hammer drill - amzn.to/3uCYU0s
*Concrete Anchors & Screws - amzn.to/3obVPC9
* Gloves - amzn.to/3bbfEnu
* Safety Glasses - amzn.to/3ux25GO
* Shop Towels - amzn.to/2SC8D93
* Tape Measurer - amzn.to/3bg83nI
* Painter’s Tape 1in - amzn.to/3uyt4BU
* Sharpie - amzn.to/3o3CZwW
* Magnetic Metal Tray - amzn.to/3hdUiJZ
* Acrylic Latex Caulk (Paintable) - amzn.to/2Q5JJ0G
* Caulk gun - amzn.to/3evIUHN
* Large Putty Knife - amzn.to/3f2CFKx
Chapters
00:00 Introduction
00:26 The Tools
02:08 The Fix
02:22 Cutting out the Old Threshold
07:20 Measuring for the New Threshold
09:20 Install New Threshold
11:30 Screwing down Threshold
13:50 Adding Chalk Under the Threshold
17:45 Adding the Adjustable Sill
19:15 Adjusting the Sill to Fit
20:38 Final Chalking
This video works on nearly all makes and models of doors. Please measure correctly and cut only what you need to!
Check out my website at mcfixit.us
Disclaimer:
Due to factors beyond the control of MC FIX IT, I cannot guarantee against improper use or unauthorized modifications of this information in the video, post, blog, or social media. MC FIX IT assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. If you feel uncomfortable at any time. Stop and go to a professional. MC FIX IT recommends safe practices when working on vehicles, your house, or any other project and or with tools seen or implied in this video. Due to factors beyond the control of MC FIX IT, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MC FIX IT.
#mcfixit #adjustablethreshold #doorthreshold #doorsills #doorsill #door #sill #homerepair #homerepairs #homeremedies #homeremedy #homerenovation #adjustablesill
Supplies used to record this video:
* GoPro Hero 7 Black - amzn.to/3f3ALtb
* 256GB Flash Drive - amzn.to/33pAueG
* Vlogging Frame - amzn.to/33tajE0
* GoPro Pro 3.5mm Mic Adapter - amzn.to/2RCURCu
* Youmic Lavalier Lapel Mic - amzn.to/2R55sWX
* Boom Stand (tripod) - amzn.to/3bdkQaw
* 5/8” to 1/4” adapter (boom to blogging frame- amzn.to/3txrVsM
* Portable Battery Powerbank- amzn.to/3vJQc0q
* 6ft USB to USB-C (powerbank to GoPro)- amzn.to/3uAS5MH

Хобби

Опубликовано:

30 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 483

@MCFIXIT 3 года назад

Learn how to replace your adjustable door threshold sill for an exterior inswing door in just minutes! The Tools: 00:26 *Adjustable Door Threshold - amzn.to/3o1WxkY *Rigid Multitool - amzn.to/3f3caVh *Rigid Sawsall - amzn.to/32JIp6q *Rigid Hammer drill - amzn.to/3uCYU0s *Concrete Anchors & Screws - amzn.to/3obVPC9 * Gloves - amzn.to/3bbfEnu * Safety Glasses - amzn.to/3ux25GO * Shop Towels - amzn.to/2SC8D93 * Tape Measurer - amzn.to/3bg83nI * Painter’s Tape 1in - amzn.to/3uyt4BU * Sharpie - amzn.to/3o3CZwW * Magnetic Metal Tray - amzn.to/3hdUiJZ * Acrylic Latex Caulk (Paintable) - amzn.to/2Q5JJ0G * Caulk gun - amzn.to/3evIUHN * Large Putty Knife - amzn.to/3f2CFKx The Fix: 02:08 This video works on nearly all makes and models of doors. Please measure correctly and cut only what you need to! Check out my website at mcfixit.us Disclaimer: Due to factors beyond the control of MC FIX IT, I cannot guarantee against improper use or unauthorized modifications of this information in the video, post, blog, or social media. MC FIX IT assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. If you feel uncomfortable at any time. Stop and go to a professional. MC FIX IT recommends safe practices when working on vehicles, your house, or any other project and or with tools seen or implied in this video. Due to factors beyond the control of MC FIX IT, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MC FIX IT. #mcfixit #adjustablethreshold #doorthreshold Supplies used to record this video: * GoPro Hero 7 Black - amzn.to/3f3ALtb * 256GB Flash Drive - amzn.to/33pAueG * Vlogging Frame - amzn.to/33tajE0 * GoPro Pro 3.5mm Mic Adapter - amzn.to/2RCURCu * Youmic Lavalier Lapel Mic - amzn.to/2R55sWX * Boom Stand (tripod) - amzn.to/3bdkQaw * 5/8” to 1/4” adapter (boom to blogging frame- amzn.to/3txrVsM * Portable Battery Powerbank- amzn.to/3vJQc0q * 6ft USB to USB-C (powerbank to GoPro)- amzn.to/3uAS5MH

@djef6028 3 года назад

Can you just replace the wood piece?

@MCFIXIT 3 года назад

@@djef6028 Yes you could if you can cut it down to size properly and drill the proper holes. Mine had issues with the wood and leaking underneath the sill.

@sgtgohara Год назад

2 things, 1- A hair dryer or similar device will warm up the mastic used to glue down the base plate and make removal easier. 2 - Instead of cutting off just one end of the new threshold so it fits the doorway, take the size of the replacement and subtract the actual doorway size and then divide the result by 2 and cut off each end that distance. This will leave you with most of the adjustment screw holes rather than the one you just cut off with no adjustment capable on that side of the threshold.

@MCFIXIT Год назад

Great tips here! Thanks for adding to the conversation! This will be helpful for others projects! Have a great day!

@midwest9757 5 часов назад

@@MCFIXIT sad thing is that you actually already knew this but decided to be lazy

@spidercrower 3 года назад

If you want to make the visible adjustment screws look better, you can trim the threshold at both ends. You can make the screws symmetrical so that there is equal distance from the screws to the end of the threshold.

@MCFIXIT 3 года назад

Yes, that’s a great option! Thanks for sharing that!

@kfsowner1 2 года назад

I was just thinking the same… The visual is enhanced. PLUS, the threshold’s adjustable feature, can span the entire width of the door, instead of losing 25% of (1of4) the adjustment capability!! Go ahead and take the extra 5-10 minutes, to make the 2 end cuts, to separate yourself from being an amateur, and shine as a craftsman!

@dollyhadbraces9361 Год назад

well if you want to "shine as a CraftsMan" better start at the supply house , as i selected the least marred packaging and did not check the screw layout. but come time for the install the screw array starts randomly .. 2" from one end on one side huge space 4-5" on the other , so select well ... the lady is super pleased ... tip ... storm doors have adjustable bottoms and the gasket is replaceable . theres "Y" and "T" one ace hardware ONLY had T and the other ONLY has Y. y and t are very similar if t looks a tiny bit to big you need y . Im might fill the holes w epoxy. i stained the wood. used 30 min bucket cement from post department. very workable and no cracks. if the others are correct at the supply house i may whine to the manufacturer to get a refund , though i know i should check first . but its sold at a DIY so ...

@dirtcvma Год назад

Great advice. Thank you

@riderhard 8 месяцев назад

Fitting the new threshold between the jams should be done by cutting equal portion from each end of the strip. (Meaning if you need to take off 2 inches, just cut 1 inch off each end.) Now the new threshold will have equal adjustment screws across the whole threshold and look much better and not something amaturish.

@mickjager5974 3 года назад

Should you cut it off both ends to leave as many of the screws that hold/adjust the wood strip in place and also kind of have the screws centered?

@MCFIXIT 3 года назад

Yes, you can definitely do this! It would help make it looked more centered. Great insight!

@nickmcfaddin4443 2 года назад

That was my very first thought when I saw the sharpie mark! My OCD self said "Oh no..."

@dgexpressllc7450 2 года назад

That is what I was thinking!

@mickjager5974 2 года назад

@@MCFIXIT Granted the factory edges would be a lot straighter than what I personally be able to cut by hand!

@teembe8123 2 года назад

Plus at the side closest to the hinges, the seal is basically unsupported by any adjustment screw. It sealed, but it could be better if that screw was there.

@aenimosity7 2 года назад

Great video, thank you!! I need to get this done before winter and it's been causing me a lot of stress, but now I feel confident after watching your video!

@MCFIXIT 2 года назад

Thanks! I appreciate you watching and commenting! Good luck on your project!

@lisamarenghi7995 2 года назад

This step-by-step video was perfect! I had the exact same problem with an old rotted threshold on a cement base. The links to EACH product was great especially since no comment was made about the size & length of the anchors (I did have to research drill bit size because I’m a 100% amateur). So many videos cut out half the work & get confusing. The absence of directions and/or the constant extra babble often drives me crazy. Yours was perfectly narrated explaining everything so well. This truly was fantastic!

@MCFIXIT 2 года назад

I'm so glad it was helpful! Good luck on your project!

@sais9221 2 года назад

Bought the exact threshold and have not a clue on how to install it. The director in the back of the label is useless! Thank you for sharing. Now I am ready to install it. Liked and subbed!💯👍

@MCFIXIT 2 года назад

Thanks but I’m so glad it was helpful!

@mitchdaniel5605 4 месяца назад

Yeah same, and the instructions said to install the t nuts backwards… like on the opposite side of the threshold baseboard. Weird.

@velia3051 3 года назад

Great tutorial on how to replace threshold. I feel super confident now to install one in my kitchen door. Look forward to viewing your other videos.

@MCFIXIT 3 года назад

Thanks so much! I hope it’s helpful and you have great success in your project!

@dwightwiest7278 Год назад

Just finished replacing my front door threshold, and this video walked me through every step. He is right when he says the toughest part is getting the old threshold out. Mine was a pre-hung door, so the original threshold was very much a part of the old door frame! The sawzall and multitool saved the day. Even after cutting the old threshold in half, it was held in by construction adhesive on the bottom and on each side by wood screws coming out sideways from the door jamb. Be careful not to tear these out; cut them off if you can. Existing flooring on the interior side was also a challenge but thankfully it wasn't too thick and I was still able to slide the new threshold in. And final lesson learned, don't use a metal hammer to nudge the new threshold in; it will mar it.

@MCFIXIT Год назад

Glad you got the project done! Yeah metal hammers can damage the finish. But glad you finished and the video was helpful!

@bryanmilne 2 года назад

Who knew something so ordinary could be so mysterious? Thanks for uncovering the mystery and making sense of how it works!

@MCFIXIT 2 года назад

You are welcome. I hope this helps you complete your project! Good luck!

@MrRtcrockett 2 года назад

Thank You MC FIX IT. I'm glad I found this video. I purchased the exact adjustable threshold to replace what I currently have. I dismantled my current Threshold and found it has additional weather proofing beneath. A metal tray, gaskets, etc. It's still a similar installation. Thank You. God Bless you sir.

@MCFIXIT 2 года назад

You are welcome! Thanks for writing. Good luck on your project!

@knightzcross419 3 года назад

Oh yeah! We had help on this video! Nice job on this removal/installation! Looks great! Happy I could assist!

@MCFIXIT 3 года назад

Thank you for your assistance in making this video. Next time you are up here, we will have to do it again!

@iSteven180 2 года назад

This video helped me tremendously! I need to install one of these on my garage door before winter comes and critters try and make their way in. Thanks!

@MCFIXIT 2 года назад

Glad it was helpful. Good luck on your project!

@Soulbloom1 Год назад

Great step-by-step, and the tool list was really helpful. I wish you had shown a horizontal view of the door closing and how it sealed from that angle.

@MCFIXIT Год назад

Thanks so much. I’ll try to do this for future videos.

@casiopea1953 2 года назад

Very helpful and deep explanation for the project! Thank you very much!

@MCFIXIT 2 года назад

Glad it was helpful! Good luck on your project!

@BobsHomeServicesLLC 2 года назад

That looks like paintable caulk. I always use GE 100% silicone in the blue/silver/white tube because it's made for extreme temperature changes. You did a great job, it's almost impossible to change these when the inside floor is higher than the threshold without disrupting the flooring.

@MCFIXIT 2 года назад

Thanks for the info! I will have to look into that for future projected. I had the paintable caulk on hand and it has worked very well for other projected. I'll look into that GE stuff thought. Thanks for the tip!

@Dragon-Slay3r 10 месяцев назад

7️⃣? 😂

@GCGomez Год назад

Thank you for the video! Getting ready to replace ours! Great demonstration and explanation.👍🇺🇲

@MCFIXIT Год назад

You're welcome!

@emilyscott8991 Год назад

Best advice for thresholds I've seen. I noticed your professionalism within the first few minutes of the video when you laid out your tools firsthand and also added cement anchors! Will be using your tips and instructions when I tackle my front door. The COVID comment was unexpectedly funny 🤣.

@MCFIXIT Год назад

Thanks so much! Best of luck on your project!

@jmpestsolutions8771 11 месяцев назад

Glad im watching this before getting into the project. I was like how is it adjustable and this video is awesome! Just hope its not raining this weekend!

@MCFIXIT 11 месяцев назад

Hope the project went well! Thanks for commenting!

@doctorcopper4844 2 года назад

This was fantastic! Thank you for making such an excellent video!!

@MCFIXIT 2 года назад

You are welcome. Glad it was helpful!

@danaandrews1637 2 года назад

Thank you so much. Loved your step by step approach. Great video!

@MCFIXIT 2 года назад

Thanks so much for watching and commenting. Good luck on your project. Happy New Years too!

@jessicaedge7854 11 месяцев назад

Heading to Lowes now to tackle this project! Thanks so much for the information I'm feeling confident we can do this!

@MCFIXIT 10 месяцев назад

How'd the project go?

@claudiorassouli1240 2 года назад

Thank you for making this door threshold sil video. I need to know how to get the sill to the ground.

@MCFIXIT 2 года назад

Are you asking how to fasten it to the ground? I used anchors and screws. You could also use tapcon screws too.

@joeaguirre3069 11 месяцев назад

Thanks for the awesome instructions. This will be my project tomorrow and it is exactly what I needed.

@MCFIXIT 11 месяцев назад

Glad it was helpful

@abelalfaro5101 2 года назад

I appreciate your time and sharing your knowledge. Thank you

@MCFIXIT 2 года назад

You are welcome. Good luck on your project!

@roberteshaw4590 9 месяцев назад

I can't add any more than anyone else has already. I would like to add that I have a ton of tools, with the exception of a multi tool. Purchased what i needed at Lowe's and bought a oscillating tool, which turned out to make the job much easier. I used Tap cons vrs what you did. Worked out OK, but would purchase what you suggested in the future. Just like to say thank you. You made the first time job, very manageable. I liked it an subscribed. Robert TN

@MCFIXIT 9 месяцев назад

Thanks for your comment and sub! That’s a big project to tackle. Glad you were able to complete it too!

@ricardomedrano4141 2 года назад

Thanks .You just helped me do my threshold. 👍💯

@MCFIXIT 2 года назад

You are welcome. I’m glad it was helpful

@vicente5776 Год назад

Thank You so very much now I am able to install my Frost King 36 in x 5.25 in Adjustable Threshold Weatherstrip

@MCFIXIT Год назад

Best of luck on your project! Thanks for watching and commenting

@sleep-escapeyourmind8759 2 года назад

AWESOME! JSUT AWESOME! Very well explained!!!! Thank you I have to do this for my back door to my house. I am on a slab so I will have to drill into the concrete like you explained. Thank you so much! RENMAN

@MCFIXIT 2 года назад

Glad it was helpful! Thanks for watching and commenting!

@slenechk Год назад

Most Excellent Video!!! Thanks. I felt much more confident after watching. Keep up the good work.

@MCFIXIT Год назад

Thanks so much!

@localone1597 4 месяца назад

Thanks so much. Great video. Now I feel more confident tackling this project.

@MCFIXIT 4 месяца назад

Go for it! Thank you for watching, and commenting!

@nel1803 Год назад

I have to replace one soon. This video was awesome 👌 and to the point

@MCFIXIT Год назад

Thanks, best of luck on your project!

@rbr30217 3 года назад

Very thorough!! Thank you!!

@MCFIXIT 3 года назад

You are welcome! Thanks so much for watching and commenting!

@sasilva01 6 месяцев назад

Fantastic video was very helpful in replacing the threshold. Thank you!

@MCFIXIT 6 месяцев назад

So glad you found it helpful! Thanks for commenting too! Hope you have a great day!

@MrRandomShorts123Go 3 года назад

this is good work thanks..this might come in hand one day

@MCFIXIT 3 года назад

Thanks! I hope it’s helpful.

@wandahoover7256 2 года назад

Just wanted to add that a storm door saved me from this repeat repair! Replaced the door and jam 2x b/f we figured this out…sometimes the rain hitting the house needs redirected. 🙃

@MCFIXIT 2 года назад

That's a great idea. I don't really want a storm door on this particular door, but I can definitely see how this would help save the threshold sill!

@gograpfn8659 3 года назад

Great video great work bro!! 🙏❤️

@MCFIXIT 3 года назад

Thanks! I hope it was helpful. Thanks again foe coming by to watch and comment!

@salharo8925 5 месяцев назад

Good informational how- to , I tried to zero in on the size screw/ anchors you used.

@MCFIXIT 3 месяца назад

Concrete Anchors & Screws - amzn.to/3obVPC9

@MsPancha2010 3 года назад

Thank you so much for your help!

@MCFIXIT 3 года назад

You are welcome. Thanks for watching and commenting!

@4u25out Год назад

Threshold on my garage door is rotted out, looking all over on the internet on how replace/to fix it, I didn’t know they sell a kit, thanks sharing.

@MCFIXIT Год назад

You are welcome. Good luck with your project!

@agcoast 3 года назад

Great Video! I bought a 7 year old house in 2019. Exterior door from garage to backyard swings out. When it rains alot, or with wind blowing towards the door, water creeps into the garage. The concrete on the outside of the door under the threshold looks chipped as if someone took a chisel or power tool and tried to knock it down - like maybe reducing the overall height at the time the original foundation was poured and the door was installed. I guess the only way to know the condition of the concrete underneath the threshold is to just dive in and take the old one off? Your video is the best I have seen, and I believe I can do this project. I will probably take my big laptop and keep it nearby so I can have your video up as a guide. If I do get the old threshold off and find that the concrete underneath it looks rough and gouged out, do you have any ideas? Have you ever encountered something like this?

@MCFIXIT 3 года назад

Thanks for watching and commenting! Sounds like a bad previous DIY. How deep is the chipping/knock down that you mention? If it’s very small and still level you might be able to just use chalk or concrete patch. If it’s really rough and broken/brittle or patch it up a bit. You may need to tear that portion and add some new concrete in that section. I know they make a small tub of concrete that you can purchase for patch work and minor repairs. Here’s a link: amzn.to/3h5QZ7c It's kinda hard to see your situation without being there. Good luck on your project!

@MsNailgun 2 года назад

Great video and I enjoyed your narration.

@MCFIXIT 2 года назад

Thanks so much!

@Samhain2323 Год назад

Great job and video !!! I like to use a much thicker bead 😉

@MCFIXIT Год назад

Thanks! Hope you have a great day. Best of luck on your project!

@weekendhomeprojects 8 месяцев назад

Found your shower light install vid. I need to change out a threashold also so this came in handy. Sub'd

@MCFIXIT 8 месяцев назад

Awesome! Glad it was helpful!

@rayhill4560 3 года назад

Thanks man great job

@MCFIXIT 3 года назад

Thanks so much!

@snowglider400 2 года назад

thanks for this. it really helped.

@MCFIXIT 2 года назад

So glad it was helpful. Thanks for letting me know and watching my video!

@drewlincoln8659 3 года назад

I need one of those multi-tools!

@MCFIXIT 3 года назад

Yes, they are so helpful in a variety of situations.

@kennethtaylor9710 3 года назад

So many uses they r great!

@gregbuzek7159 Год назад

Super helpful, thank you.

@MCFIXIT Год назад

You are welcome! Glad the video helped!

@user-zg7hd2ow9b 29 дней назад

Thanks !! Very useful and easy to follow video.

@MCFIXIT 29 дней назад

Thanks so much! Hope your projects goes well!

@stevocurry2380 2 года назад

You know to really professionally install that treshold it's a rubber seal that also goes to the bottom of the door itself" it extra seals from water or lil insects ! Also that hole plug & screws was cool but u can also just use tapcons or whatever works...you did a great job showing & teaching

@MCFIXIT 2 года назад

Thanks! Yes, you can get a rubber seal. I didn't have any tapcon screws with me on this job but that's definitely a good solution as well. Thanks for watching and commenting!

@DAK4Blizzard 2 года назад

Yeah, my basement exterior door is in a situation that I think could use both a threshold and rubber seal. My door is located at the bottom of a stairwell, which has a drain only about a half foot in diameter. When it rains very hard for more than an hour, there's a chance the drain will get clogged from runoff debris and cause water to back up into the stairwell. My door already has a seal attached on the bottom interior side of it, but it's not quite enough. (The basement will get large puddles inside near the door once every few years on average, so it's serious, but not extremely so.) I'm hoping that installing a threshold in front of the door will block even more water from having access to under the door. I hope it can further help, even if not perfectly. On a side note, I just replaced that door's frame mostly with PVC trim boards, because most of the wooden fame within a couple feet of the ground was rotting from the prolonged moisture and water at the bottom of stairwell. (Even some parts toward the top of the frame were beginning to rot as well.) I'm hoping the PVC will hold up better against the humidity and water.

@MCFIXIT 2 года назад

I’d def go with a good seal for your application! Also that PVC board is good around wet areas. I helped install some of that on my grandmas garage door frame bc it was a low spot on her driveway (very bad design), and it would rot about every 5 or so years. That PVC stuff has lasted over 8 years and has no signs of water damage. I wish you luck on your project!

@DAK4Blizzard 2 года назад

@@MCFIXIT Thanks for the reply. If you don't mind, I have a couple follow-up questions for my situation. I'll do my best to sum it up to make this simple enough to try answering. As mentioned: we took complete care of the perimeter around the door. (That's encouraging to learn that your PVC has lasted 8+ years with zero damage.) The door already has an attachment on the bottom interior side of it. And now we're considering some kind of threshold on the exterior side of the door to keep as much water out as possible. Additional info: The bottom of my door (not accounting for the attached seal on the bottom) is about 1/2 inch above the ground. The ground is flat and made of concrete both inside and outside the door. My questions: You suggest "a good seal" for my door. Do you think attaching a rubber seal to the ground just outside the door would beat a threshold? If a threshold is a decent option, can I get away with using a threshold without wood parts? (I'm concerned wood parts would rot quickly on the exterior side of the door, where water is common and helped rot my previous wood door frame.) Thank you either way, and I do understand any advice you generously offer is free from liability.

@mram7715 Год назад

Appreciate the vid. Great explanation

@MCFIXIT Год назад

You are welcome! Have a great day! Good luck on your project!

@Kevthebish Год назад

Not bad. I was a little fuzzy on the washer system for adjusting but I'm sure I'll get through it. Your storage shed will be nice and toasty now.

@MCFIXIT Год назад

Thanks so much! Hope you have success on your project!

@ReviewTimeWithTim 3 года назад

this is a good video...thanks or making this.

@MCFIXIT 3 года назад

Thanks for watching and commenting, please visit my channel again!

@ztrrottweilers6383 Месяц назад

Thanks mine is installed now

@MCFIXIT Месяц назад

Awesome. Hope the video helped. Thanks for watching and commenting!

@jtwad 7 месяцев назад

Thanks for your excellent video.

@MCFIXIT 7 месяцев назад

Thanks so much!

@shelbybeal8688 2 года назад

Great repair video!

@MCFIXIT 2 года назад

Thanks so much!

@MCFIXIT 2 года назад

Thanks!

@danielgao52 2 года назад

Very Very Good !!! Thank you 👍👍👍

@MCFIXIT 2 года назад

Thank you too for watching and commenting! Good luck on your project!

@richardrosales9427 Год назад

Thank you for the video. It is very helpful.

@MCFIXIT Год назад

Thanks so much. Best of luck on your project!

@richardrosales9427 Год назад

@@MCFIXIT Hi, one more question, I did not see the link for the all the tools needed. I very savy with RU-vid.

@MCFIXIT Год назад

It’s in the video description… The Tools: 00:26 *Adjustable Door Threshold - amzn.to/3o1WxkY *Rigid Multitool - amzn.to/3f3caVh *Rigid Sawsall - amzn.to/32JIp6q *Rigid Hammer drill - amzn.to/3uCYU0s *Concrete Anchors & Screws - amzn.to/3obVPC9 * Gloves - amzn.to/3bbfEnu * Safety Glasses - amzn.to/3ux25GO * Shop Towels - amzn.to/2SC8D93 * Tape Measurer - amzn.to/3bg83nI * Painter’s Tape 1in - amzn.to/3uyt4BU * Sharpie - amzn.to/3o3CZwW * Magnetic Metal Tray - amzn.to/3hdUiJZ * Acrylic Latex Caulk (Paintable) - amzn.to/2Q5JJ0G * Caulk gun - amzn.to/3evIUHN * Large Putty Knife - amzn.to/3f2CFKx

@TheGuitarlad Месяц назад

The washers need to be driven onto the bolt so that they are secured to the adjustment board. Flat side of washer against the wood. I used a longer 8mm socket and tamped the washer down over the bolt. This will snug the bolt to the wood and the adjustments will work correctly.

@MCFIXIT Месяц назад

Great tip! Thank you for adding this

@josephmartinez7006 3 года назад

Great video

@MCFIXIT 3 года назад

Thanks so much! I hope your project goes well.

@regihamp0206 Год назад

Thanks very helpful

@MCFIXIT Год назад

You are welcome. Best of luck on your project!

@markzellner1702 Год назад

Funny the instructions with the threshold didn't indicate exactly where the nut you hammer into the wood goes. I had to watch your video to find that out. Very helpful.

@MCFIXIT Год назад

Glad you found it helpful! Best of luck on your project

@Kleeschulte Год назад

Thank you...good job.

@MCFIXIT Год назад

Thanks! Best of luck on your project!

@tomashernandez711 3 года назад

This was pretty damn cool! Thank you for sharing! What would be your approach if the concrete had settle leaving a huge gap on one side? Would you shim then caulk underneath?

@MCFIXIT 3 года назад

Great question! It matters how much of a gap there was. If it's over a 1/4 of an inch I would try to get some sort of concrete patch (amzn.to/2RubRv1) and even it out across where the threshold would sit. Then chalk it like the video after it's all of the way dry. You may be able to get away with just chalk but that's depending on the amount of settling that has occurred. Thanks for watching and commenting! Have a great day and good luck with your project!

@tomashernandez711 3 года назад

@@MCFIXIT Thank you!

@MCFIXIT 3 года назад

You are welcome! Good luck

@bryanmilne 2 года назад

Awesome! 👍

@MCFIXIT 2 года назад

Thanks! 👍

@warfarin12 3 года назад

This video was perfect! Can you tell me what size anchor and screw you used on the project?

@MCFIXIT 3 года назад

I believe they were 1 1/2 or 1 1/2 inch. Here’s a link: Concrete Anchors & Screws - amzn.to/3obVPC9

@donnasfix-it3861 Год назад

Helpful video! The adjustment screw on one end is just spinning freely (not adjusting height). Does that mean the threaded insert is spinning freely as well and if so, is there some way to pull them both out? I've tried a small pry bar, but it's just wrecking the wood strip that I was planning to repair.

@MCFIXIT Год назад

Do you happen to have plastic trim tools like for removing plastic components on a vehicles dash. That would help you not mar the wood

@ifixeditmyself1926 Год назад

Very helpful 💯💯💯

@MCFIXIT Год назад

Awesome! Congratulations. Thanks for writing a comment and watching my video

@TEBCO123 Год назад

great video

@MCFIXIT Год назад

Thanks so much

@mmedrano21 Год назад

Tapcons work great

@MCFIXIT Год назад

Great tip!

@jawbrace 2 года назад

Nice video. I have a 5 foot French door that seems to be bowing (rising in the center). Do you have a good remedy for that? It seems like replacing the entire unit would be opening up a can of worms.

@MCFIXIT 2 года назад

No, sorry. I haven't had the opportunity to do something like that. I'd check to see if others have done this one RU-vid or hire a professional. Typically you can see if it's a doable project or not by watching others do it.

@Rezar_racing 3 года назад

Good to know tnx ;)

@MCFIXIT 3 года назад

Glad it was helpful. Thanks for watching and commenting!

@MitchellJames_Snowl Год назад

Thank you for the video. I'm going to use flexseal instead? It rains a lot here and I don't have gutters...yet (Future diy) First time trying this...Here we go.

@MCFIXIT Год назад

Best of luck! Have you completed it?

@MitchellJames_Snowl Год назад

@@MCFIXIT Ummm, LoL. Turned out to be a huge problem. As I took off the old threshold, the worse you think could happen...happened. everything under the threshold was rot. The wood was soaked. omg remember i have never done this before. It was a nightmare for me. but, I finally got it done. Now tomorrow I will put the final piece on...the new threshold.

@MCFIXIT Год назад

Awesome! I'm glad you could preserver through the issues and are able to finish the project! Wood-rot is a serious issue and can lead to lots of leaks and even mold in houses. Glad you were able to fix it!

@Sparisland 5 месяцев назад

You can get scraper blades for the multi-tool that make removing that adhesive easier.

@MCFIXIT 5 месяцев назад

Awesome. Thanks so much. I’m sure this will Be helpful to others watching this video.

@Sparisland 5 месяцев назад

@@MCFIXIT (Super cheap on AMZN btw). Great vid, Thanks.

@toma.rogers6647 3 года назад

Do you have to cut it in half? Can you just use a crow bar and pry it up? I'm afraid of ruining the door frame if I do it that way, but I don't have a multitool or sawsall.

@MCFIXIT 3 года назад

I would recommend doing it this way. Often they place a lot of chalk or liquid nails under it. This will enable you to save as much of the door jamb as possible. Often the sill is attached to the jamb on both sides with nails.

@freak3dot 2 года назад

They make a scraper attachment for the multi-tool. Works way faster than scrapping by hand.

@MCFIXIT 2 года назад

I’ll have to look into that attachment. I knew they made a bunch of attachments but not one like that!

@freak3dot 2 года назад

@@MCFIXIT I recently used it to remove some kind of sealant from a concrete foundation crack that was leaking. I was thinking grinder at first. But, the scraper removed it in larger pieces with less dust. I still followed up with a grinder at the end to really get back to concrete. But, I was glad I used the scraper first because the grinder was so dusty and stunk. No leaks since I injected the crack and it made me a believer in the multi-tool scraper.

@MCFIXIT 2 года назад

Thanks again! I’ll have to look into that!

@Bk-uz3pk Год назад

Thank you

@MCFIXIT Год назад

You are welcome. Good luck on your project!

@ryanflippin1243 2 года назад

Subscribed, liked, and commented obviously 😂✌️

@MCFIXIT 2 года назад

Thanks so much!

@joegw1987 2 года назад

Nice video

@MCFIXIT 2 года назад

Thanks!

@onlyme8870 2 года назад

Wish I saw this. Just did one that wasn't attached and frame was rotted and screws that held the frame snapped off as it was just pushed into a cement opening no shims all that held it was 2 screws on each side and silicone.the sill wasn't secured at all but once it rotted wiggles out. And under it was just 2 bricks. But I did get the adjustment type sill. I have one more to do and I think its the same.

@MCFIXIT 2 года назад

Hope you are able to complete your project! Good luck!

@onlyme8870 2 года назад

@@MCFIXIT one the frame is rotted and not square and ahimmed. So going to start that from scratch. Ill repair the jam. Its always more than they say is needed. Lol

@hgodtx 2 года назад

Question: At 11:54 you drill the holes, then at 16:50 you adjust the plate to the door. Shouldn't you have done that in the reverse order? I'm confused how at 17:18 installing the screws didn't just slightly move the plate back into the positioning of the original "holes drilled" positioning rather than your "adjusted to the door closed" positioning. Thanks so much for this video, now I'm not scared to tackle it myself!!!

@MCFIXIT 2 года назад

Yes, it would go back into the same spot. So no worries. Best of luck on your project!

@carlosvpallares1407 7 месяцев назад

Exelente gracias

@MCFIXIT 7 месяцев назад

You are welcome!

@gavinmccreary4873 10 месяцев назад

Does the caulking keep the end of the metal portion from sticking up? I ran into this when I installed without caulking and would like to make it lie flat so it doesn't catch on any toes.

@MCFIXIT 10 месяцев назад

It should assist with holding it down. The screws also do that as well. If you are worried, you could put down a base of something like liquid nails meant for concrete & metal.

@averymaples8472 Год назад

Just wondered if the water coming underneath the threshold was stopped. I have to do this to a basement door with a rotted threshold and would have used a lot more caulk underneath it. Looks doable.

@MCFIXIT Год назад

No leaking issues and it’s been over two years with many rainstorms. You can definitely use more caulk if you’d like to do so.

@TankGunner84 4 месяца назад

Nice video but you do know you were using acrylic caulk for paining, you need a good silicone caulk to with stand time and keep the water out. That just to fill gaps for trim and stuff not actually stopping water or anything.

@MCFIXIT 4 месяца назад

Thanks for the tip! I’m sure this will be helpful!

@stevecundiff8252 Год назад

I can do this but the problem is that the double doors measure 72 inches but the opening measues 73 1/2 inches wide and the left side of the entrance is more than an inch lower than the right side, in addition to having some sort of hardware on the floor, center, for the rod which closes the left door. The doors were installed without threshold many decades ago and the floor is cement. Any advice is appreciated.

@MCFIXIT Год назад

You will need to level the floor first off. I’m a little confused about difference of the size on the double door, can you rephrase it?

@kirkhall2099 2 года назад

COVID Safe licking your finger. RIDICULOUS.Total over reaction. Turn of the news and enjoy life. Thanks for the video. I bought the same brand and this video helped.

@MCFIXIT 2 года назад

Lol. Im trying my best to enjoy every moment of life :) Thanks for commenting and watching the video!

@kcolfer Год назад

One would think that somebody would make just the wooden adjustable sill. Then you wouldn't have to replace the whole threshold when its just the sill that needs repair. I have this problem on 3 doors in my house. All the doors had the adjustable sill removed by a previous owner. I'm thinking there must be a way to manufacture just the sill. Any ideas?

@MCFIXIT Год назад

Let me know if you find out. These only last so long and then they are shot. Thanks for watching and commenting!

@billjensen51 Год назад

And for the next video you can show how to replace damaged door frames

@MCFIXIT Год назад

Yeah. I need to do that to this door frame. It’s got a bit of wood rot from the old leaky sill.

@ethandaigle258 11 месяцев назад

Really great video! Your drill sounds like its on life support lmao

@MCFIXIT 11 месяцев назад

It might just be my old mic. I’ve got a much better one now

@susanburge6105 Месяц назад

This is a helpful video. I was wondering why you aren’t wearing 🧤? I keep thinking you’re gonna cut your fingers. 😮

@MCFIXIT Месяц назад

Definitely an option. I’ve been doing work with my hands for years and are quite careful with what I do but if it makes you feel more comfortable and confident, then definitely wear gloves! Thanks so much for watching and commenting!

@jmpestsolutions8771 11 месяцев назад

Seems like if you applied the nails adhesive to the wood plate instead of the concrete that thos would be better? My threshold is weird cause its on the basement wall I believe. I dont know if I need a new subfloor strip to anchor to :(

@MCFIXIT 10 месяцев назад

That's def an option. My biggest issue was sealing out the water and that's why I used caulk.

@jesustrujillotileinstaller6133 3 месяца назад

How about the last piece the one you did cut with a lot of glue under to seal the threshold ?

@FounderOf4 2 года назад

This is hands down the best video that I have found for replacing these thresholds! Well done sir

@MCFIXIT 2 года назад

Glad it helped. Thanks for watching and commenting!

@Powerfade54 Год назад

You should have taken a bit from each side as opposed to cutting to length from only one side. or drill another hole to secure it properly.

@MCFIXIT Год назад

Yes, this is a great tip. Thanks for adding it

@paidinfull5950 6 месяцев назад

Nice job with what you’re working with But Never understood why people go thru all that and leave the door with the bottom jamb in that poor condition, won’t be long the whole frame will rot out at the bottom, you can get a pre hung entry door , 6 panel steel with frame and threshold and all for $100-200 and have a factory installed threshold and unit and have it installed in about the same amount of time. I install doors everyday, that’s all I do for 9 years now. I install them in 1-3 hours, a door like this would take hour tops.

@MCFIXIT 6 месяцев назад

That’s 100% an option. I’m planning on repairing the frame soon. Thanks for adding it the conversation!

@armandohernan4610 8 месяцев назад

I did mine and put it the same way as it was, question thou, there is a gap in between, is there supposed to be a gap?

@MCFIXIT 8 месяцев назад

Where is the gap?

@jlk8145 2 года назад

Should use the cut off piece as a guide to mark sides to fit new threshold

@MCFIXIT 2 года назад

Great idea. That’s definitely a good option!

@NsyShwl 3 года назад

I wonder if you can leave one side higher than another to be able to close an angled gap

@MCFIXIT 3 года назад

You could to this. One question I have is what is causing the gap? Uneven floor? Door? If you can answer and possibly fix this, then there would not need to be an angle at the threshold. BUT yes, you can have each screw at differing heights.

@NsyShwl 3 года назад

@@MCFIXIT thanks alot for the reply! I'm helping a neighbor of mine fix her house which had a really bad foundation problem that unfortunately caused the door frames to be off square and so the gap underneath the front door has 1 3/8" on one side and 1 3/16" on the other side and I was trying to fix the gap so water stops coming into the house without having to rip into the door frame to try and straighten it.. I'm not making any money on this job nor does the homeowner have any money to pay for it so I'm trying to do the best I can without spending a ton of money.. again thanks for the help I look forward to more of your videos!

@charmerxxx 2 года назад

@@NsyShwl You would shim the new sill bringing it up to level with ice and water shield in layers then caulk the front edge.

@csullivan626 3 года назад

How well does the adjustable piece hold up to traffic? It looks like all that is keeping it up are some washers, and a big guy like me stepping on it would just push it down. If that does happen what’d be the fix, shims?

@MCFIXIT 3 года назад

That’s what the original had and lasted 17 years. I’m a pretty big guy too. But yes, I’d say shims could be a replacement. I’d figure out the exact height and length and cut your shims downs. I’d also drill out holes and allow the hardware to be used properly. It might take a couple of tries to get the shims to the correct height and size. I think that’s why the system they use is designed like that bc it makes it quite easy to raise and lower the adjustment by simple Philips screws.

@kennethtaylor9710 3 года назад

I had just that issue. I used JB weld to fix the washer in place. It’s holding good so far.

@kennethtaylor9710 3 года назад

JB WELD the washer in place.

@csullivan626 3 года назад

Thanks @Kenneth Taylor!