How To Install CROWN MOLDING using

Подписаться 9 тыс.

Просмотров 1,1 млн

50% 1

Using the SAWSET PROTRACTOR with any t-bevel and miter saw, handymen and DIYers can learn how to install CROWN MOLDING easily and accurately for a perfect fit, every time. SAWSET PROTRACTOR - SOLD ON AMAZON This RU-vid video will give you, tips on how to measure, find angles, cutting with a miter saw, nailing, caulking, seams/scarf joints, end cap/returns, inside and outside corners, filling holes, gluing, and much more!
It will also show you how to use this unique carpenters protractor that has been redesigned to be compatible with any miter saw. Unlike a standard protractor it's scales have been calibrated to give perfect miter saw settings every time with absolutely NO MATH NEEDED! It is large and easy to read so finding fractions of angles is possible for that perfect fit.
To get that professional look when installing Crown Molding, Baseboards, Wainscoting, Stairs/Railings, Hardwood Floors, Decks and Fences, SAWSET PROTRACTOR and your sliding t-bevel will always give you those perfect angles. It is also an essential tool in your wood shop and in your tool belt!
The miter saw cuts at a fraction of degree, so why not have an angle finder that can do the same? This tool is the perfect companion for your miter saw. If you own a miter saw, you NEED a SAWSET!
Your Miter Saw is designed with 2 adjustable angle settings. One at the back, which enables you to tilt/ lean the blade, which gives you the bevel setting. The other is on the front of the saw parallel to the table, to adjust the miter setting. These settings done correctly, will give you that satisfying perfect fit!
The Sawset Protractor is able to find the saw setting for every condition with no calculations necessary.
SAWSET PROTRACTOR - The perfect tool for the perfect job!
Thanks for watching and keep checking for more How To Videos.
Please subscribe and leave your comments or questions below.
For more info about SAWSET PROTRACTOR see our website.
www.sawset.ca/
Sold on Amazon.com
www.amazon.com/dp/B0C9V6S411
Sold on Amazon.ca
www.amazon.ca/Protractor-Alum...
Purchase the New SAWSET PRO PROTRACTOR on our website.
www.sawset.ca/where-to-buy
TIMESTAMPS:
0:00 Intro
0:46 Find your measurements and miter saw setting.
1:53 Cutting your angles on the fence.
2:30 Installing your crown - gluing, nailing and tips!
4:55 Making a return or end cap.
6:20 Caulking tips.
7:20 Making seams perfectly!
9:43 Outro

Опубликовано:

3 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 456

@tomshieldsmith9687 4 месяца назад

Watched 4 videos before I found this one. Could've saved myself half an hour if I found this first! Very helpful. Thanks!

@SawsetTools 4 месяца назад

Thanks. Glad to be helpful.

@sbtencar8243 6 дней назад

Very great tutorial i found, i need to tell my husband to watch this video so we will try to do our house crown molding. Jordan , thank u for sharing this video

@SawsetTools 6 дней назад

Glad it's helpful. Thanks

@spicyhot1695 4 года назад

I wish I had seen this video 5 years ago when I installed my crown molding, it would have made the job a lot easier. Great video. Thanks for sharing

@SawsetTools 4 года назад

Thanks for your comment.

@sealcycle2020 3 года назад

I WISH I SAW THIS VISEO 1,000 BOARD FEET AGO

@cassiellightman 4 года назад

One of the best videos teaching how to cut crown molding. Thank you!

@SawsetTools 4 года назад

Thanks for the compliment.

@deldeek 4 года назад

Yet straight to the point i didn’t see and explanation how you placed the crown on the miter what side for which ( left or right ) , from which point to what point you measure the molding ! That’s where the struggle is ...besides that thanks for sharing

@SawsetTools 4 года назад

Sorry. Limited time.

@u.sonomabeach6528 2 года назад

Thought I was gonna be surfing videos for hours but your video had me back working quick. Thank you for being competent, clear and concise! One thing I will say though is there IS one person who wants to be called stumpy….Stumpy Nubs Woodworking channel 😉

@SawsetTools 2 года назад

I love Stumpy Nubs!

@SawsetTools 2 года назад

Thanks for the compliment.

@mrdman094081 4 года назад

Agreed. You make it look easy and uncomplicated, the opposite of what it is. That's a skill.

@SawsetTools 4 года назад

Thanks, years of repetition.

@PerfectPicture2012 4 года назад

What a great detailed video, good job on molding and video!

@SawsetTools 4 года назад

Thanks for the compliment.

@patrickmayer9566 5 лет назад

Mr,jordan,,,thanks for this vid,I used this on my new job,just starting,you showed me just what I needed!simple,to the point,can't wait to have a nail gun!old school😐..also how to glue and clean up!!!!a plus...land o ' lakes,wi.usa.

@SawsetTools 5 лет назад

Thanks Patrick! Good luck on your project.

@toreyyoung1518 5 лет назад

#1 you are very informative. #2 great detail #3 I had long hair for Years. Ponytails men & women. Buns...female ballet dancing.

@SawsetTools 5 лет назад

Thanks for your positive feedback!

@ringokissu 5 лет назад

Great video! My husband found this very useful. Thanks!

@SawsetTools 5 лет назад

Thanks

@mary-bethdouglas2936 5 лет назад

Great Video, gonna get this for my husband for sure

@SawsetTools 5 лет назад

Thanks!

@BlankHouseCoLLC 4 года назад

Very good tutorial and simple explanation. I was sharing this with one of my helpers to help better explain the concepts of setting crown and how measurement increases are very important so you don’t burn material by 1/8” or 1/4” trying to get a fit inside corner/outside. 👍🏻

@SawsetTools 4 года назад

Good call.

@ricardogalvan6700 Год назад

What type of glue are you using

@lordbyron4163 4 года назад

Nice.... Thanks for this one. Been dying to attempt my victorian coving.

@alaverga3455 4 года назад

Make it look so easy, this guy is a pro and is very skilled👍

@SawsetTools 4 года назад

Thanks, I do it for a living.

@bennyholguin7032 3 года назад

Thank You for the video. It was Very Informative! You made it look EASY!

@thetoolman3355 3 года назад

Thanks Ben for the Compliment.

@luisbanda7063 2 года назад

THANK YOU , WONDERFUL TIPS ON THIS VIDEO !!!

@SawsetTools 2 года назад

Thanks for your compliment.

@cloudflores9838 4 года назад

Oh wow this video was fun, easy and very informative to watch! Thanks man

@SawsetTools 4 года назад

Thanks for your positive comment.

@maureenmellegers6582 3 года назад

Great video on installing crown molding.

@SawsetTools 3 года назад

Thank, Moe

@matthewo755 5 лет назад

Great video, lots of helpful tips. Thanks.

@SawsetTools 5 лет назад

You're welcome!

@ScubaDiverMagazine 10 месяцев назад

Took ages to find a decent video like this. Thanks.

@SawsetTools 10 месяцев назад

Hi to the UK. Thanks for taking the time to comment. Glad the video was helpful.

@foreignercatracho 4 года назад

Thank you so much for sharing your knowledge. I learned a lot of tricks

@SawsetTools 4 года назад

Thanks for your compliment.

@cynthiaescobar3762 4 года назад

Great advice! I learned a lot!

@BigmoRivera 4 года назад

Great Tip Nice Work... Awesome Tool. 👍

@SawsetTools 4 года назад

Thanks for you input!

@bartonchu670 3 года назад

Jordan, Great video explaining how easy this protractor is to use and how accurate it can be. Well worth the $20+ and it is so compact for storage. Works simply with the T-bevel you likely already have. Your instructions on applying latex caulking to all joints and surfaces before installing the molding to ceiling and wall was so helpful to successful completing our room. When installing long pieces it is like a 3rd hand holding the molding in place while you position and nail. Super suggestion and a great help to ensure the piece is permanently held in place.

@thetoolman3355 3 года назад

Barton thanks for the compliment. Merry Christmas

@SawsetTools 3 года назад

Thank you for your positive feedback. It's so great to hear success stories and how Sawset and our videos have helped you improve your carpentry skills. That's our goal!

@247videogame 2 года назад

👍👍 excellent!

@SawsetTools 2 года назад

Thanks!!

@bryonsview 4 года назад

Thank you for sharing. This video was extremely informative. Way better than the old homes guy. Lol. I have to order that tool that allows you to measure angles.

@SawsetTools 4 года назад

Thanks for your comment

@jewelsbaby2449 2 года назад

🙌🙌🙌 great job!👍🏽

@SawsetTools 2 года назад

Thanks, Glad you liked it.

@salompita 4 года назад

You make it look so easy but at the end it’s beautiful

@SawsetTools 4 года назад

Thank you for your nice comment Jenie.

@normajk2 4 года назад

Thank YOU !!! very helpful !!! Good Job !!!

@thetoolman3355 4 года назад

Thanks for the compliment.

@thetoolman3355 5 лет назад

Very informative video, thx!

@SawsetTools 5 лет назад

You're welcome!

@joseluismacias3878 4 года назад

Muchas gracias amigo muy bien explicado tu video aprendi bien todo, boy a empesar mi proyecto

@thetoolman3355 4 года назад

Thanks for your compliment.

@rickwaldner8078 3 года назад

Im a fine woodworking carpenter by trade for the past 20 years, lots of good tips on this video, how ever, the ceiling you were working with was exceptionally good, most of what we come across is much worse with being off level and bade bumps / dips in the ceiling. it can get much more complicated at times.

@SawsetTools 3 года назад

You are right Rick. I have done a lot of old homes and plastered homes are the worst. I'm retired now, and that's my son on the video. Thanks for the comment.

@SassyHilda 4 года назад

You made it look so easy.. impressive detailing

@SawsetTools 4 года назад

Thanks Sassy.

@miguelespinoza8602 3 года назад

I love it !

@SawsetTools 3 года назад

Thanks Miguel. It's always nice to hear a compliment.

@Nicole-fj3pt 5 лет назад

Beautiful

@SawsetTools 4 года назад

Thank you! Are you talking about Jordan, hahaha!!

@madjack5002 4 года назад

Your skill is impressive. Thanks for the video. I bought the Kregs jig today. And all of the videos say to cut it top down. They left me wondering what the hell is the top and what is the bottom. Hopefully mine turns out looking like this. I bought about 40' extra just to practice with.

@SawsetTools 4 года назад

Thanks for the tip.

@PVTOW 5 лет назад

Awesome Video !!

@SawsetTools 5 лет назад

Thanks!

@jordanostachowski4708 3 года назад

Great video!

@SawsetTools 3 года назад

Thanks!

@seven73ify 5 лет назад

Awesome! Thanks

@SawsetTools 5 лет назад

Thank you!

@zaneh6188 5 лет назад

GREAT VIDEO, Well informative. Thanks

@zaneh6188 5 лет назад

where can i find that clamp or metal plate on the Dewalt miter saw? i have the same saw

@SawsetTools 5 лет назад

@@zaneh6188 it's called "Crown Stop". I bought it at Lowes. It's also available on Amazon. Thanks for your comment!

@yichalnegussie5401 4 года назад

Great Job in providing nice tips and tricks, I got answer to my questions Thank you

@SawsetTools 4 года назад

Thank, My pleasure.

@U2BER2012 2 года назад

Say...you're pretty good. I like this video; simple yet very insightful!

@SawsetTools 2 года назад

Thanks, I try my best.

@robertosalazar3628 4 года назад

Master good job 👍

@SawsetTools 4 года назад

Thanks

@casperlokz8348 4 года назад

Good stuff!!

@SawsetTools 4 года назад

Thanks for your input!

@DiannaAtherton 3 года назад

Finally a video on crown I understand. I was so confused about turning crown inside down before cutting. Thank you. Can you share what glue your used? Thanks

@SawsetTools 3 года назад

We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works. Thanks for your positive comment.

@JohnDoe-ft2nh 4 года назад

Great video.Thanks man.

@SawsetTools 4 года назад

Thanks for the compliment.

@moisesrobles7884 3 года назад

Nice work bro and tips thanks keep it up lm smashing my like botton katakabooooooooooooom

@SawsetTools 3 года назад

Thanks. Love that expression.

@joelewis2401 5 лет назад

Great video

@SawsetTools 5 лет назад

Thanks!

@Kaladesignbg 2 года назад

Great job!!

@SawsetTools 2 года назад

Thanks, always nice to hear a compliment.

@ivankotarscak5014 4 месяца назад

Simply best

@SawsetTools 4 месяца назад

Thanks Ivan,

@cancerenergy2464 2 года назад

Great video💪🏽💪🏽

@SawsetTools 2 года назад

Glad you liked it!!

@billzima7068 4 года назад

Need a cushion on that gun. I would highly recommend not caulking nail holes. Use a filler that wont shrink. I use a product i think from DAP but we push it in really good then just little on the heavy side. The filler is super lightweight and can really be sanded by hand. But we just run around tje room with a sanding sponge..it only takes a few minutes and it smooths out any of the crap primer job, the over fill of filler we applied and makes splices and outside corners flawless. Also dead end returns we use CA glue and put it together on the bench b4 it goes up. Blocking,splices and outside corners use wood glue!! Inside corner we cope and then apply a small bead of caulking with adhesion b4 fitting together. Keep everything clean as you go. I like having a wet sponge with me but only to keep my finger clean and moist to slick over the caulking. Crown molding is one of them things where it can be tough in the beginning but when that lightbulb goes off in your head and you totally understand it ..it then becomes as easy as installing baseboards. Very nice angle finder..with that and a bevel gauge you are guaranteed a beautiful outcome. Happy building all!!:)

@SawsetTools 4 года назад

You are right. Thanks for the helpful tips.

@H2oToGoWH 3 года назад

Nail hole tip ; use drywall putty, you can sand it lightly or wet cloth when it’s close to dry. I find caulking doesn’t fill that great, but that’s just me.

@thetoolman3355 3 года назад

You are right. Dryway compound is the best way. My mistake.

@mregan3855 4 года назад

Great video,,

@SawsetTools 4 года назад

Thanks for the compliment.

@bobdavis3389 4 года назад

Very good , informative , !!

@SawsetTools 4 года назад

Thanks Bob

@anthonykhan3424 5 лет назад

Very good work tanks

@SawsetTools 5 лет назад

Thanks for watching!

@irisostachowski1489 4 года назад

Most silicon caulking's are NOT paintable. Be careful paint will not stick. We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@hakeemlayode1474 4 года назад

Thanks nice n really enlightened

@SawsetTools 4 года назад

You welcome.

@HaNguyen-iq8un 4 года назад

I like your video .

@SawsetTools 4 года назад

Thanks for your positive comment.

@sams872 2 года назад

good video, thanks

@SawsetTools 2 года назад

Thanks for the compliment.

@bbundy1069 4 года назад

Excellent video. Thanks for sharing.

@SawsetTools 4 года назад

Nice to hear.

@gamerm4876 4 года назад

Hey great video thanks for taking the time too teach us all how too do this . Question what size nails are you hitting that crown molding with ? Also what type of glue are you using ? Thx

@thetoolman3355 4 года назад

2 in. 18 ga. Brad nails, trying to hit the studs when I can. We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@carmelojeronimo8497 3 года назад

Nice job

@SawsetTools 3 года назад

Thanks Carmelo

@janetcampbell5360 4 года назад

THANK you for your amazing informative information.

@SawsetTools 4 года назад

Thank you for your comment!

@AndyB718 4 года назад

You're Hired ! Ty for the video.

@thetoolman3355 4 года назад

Thanks for the positive comment.

@anilpodgornik8206 4 года назад

Nice video. I agree I pays of to measure corners beforehand. Just like to add that in my experience there's no need for a nail gun if using an appropriate glue. Although i use type of quick glue for the corners, wich means they stay in place, if the corner glue is slow acting ther is possibility of them moving out of place.

@SawsetTools 4 года назад

Food for thought!

@sharonhoare5790 4 года назад

Anil Podgornik I have never used nails in this way either. I only use them as supports underneath go stop long runs sagging, and then only if needed. Of course they get removed afterwards.

@SawsetTools 5 месяцев назад

Have a great day.

@juanfernandez8060 5 лет назад

the video is wonderful. very good instructions. have a great success

@SawsetTools 5 лет назад

Thank you!

@paulinemonastero322 4 года назад

Your how to videos are the best we’ve seen as far as clear precise descriptions and make us feel like we can tackle it ourselves so thank you. Do you mind sharing under your descriptions, what wood glue you use as well as name of seem and hole filler please? This would help eliminate the guess work when we need to purchase.

@paulinemonastero322 4 года назад

Another note if you don’t mind, what model and where to purchase the mitre saw you are using and what the actual brackets you use to hold crown moulding in place on the saw table?

@thetoolman3355 4 года назад

We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works. We use drywall compound to fill holes.

@thetoolman3355 4 года назад

@@paulinemonastero322 Any miter saws with a 12 inch blade is good. Each brand will have there own crown stop.

@ericcharp4388 3 года назад

Easy peasy. Ya right!!

@thetoolman3355 3 года назад

Eric, patients is the key.

@ECO-AFRO 2 года назад

Wow! If you know, you know

@SawsetTools 2 года назад

Thanks

@knotallthere66 4 года назад

Caulking nail holes okay yea ya do it once in awhile ,best is quick dry Spackle goes in like butter and it’s sandable ,

@SawsetTools 4 года назад

You are right. Thanks for your comment

@barrygordon1173 3 года назад

And no glue on bottom of crown...brads only...want to be professional...

@atillausta8514 2 года назад

Very good thans

@SawsetTools 2 года назад

Thanks again.

@sheriwormsley9313 4 года назад

Would you please come to my house and install my crown? Amazing work !

@CornelioAustin 2 года назад

Nice

@SawsetTools 2 года назад

Thanks

@SawsetTools 5 месяцев назад

I use a cordless drill, with a fine bit to find studs.

@TMac0925 4 года назад

Wish I had watched this before cobbling up my first attempt at crown molding. 🤦🏼‍♂️

@SawsetTools 4 года назад

Glad I was helpful.

@despistado75 4 года назад

👌💪👌

@zulmarosario1346 4 года назад

Nice video thanks for sharing. Can I only use glue my wall are plaster and I think it hard for those nailer

@SawsetTools 4 года назад

Plaster fractures when nailing. I recommend you nail to the studs.

@dmlvsccfamful 3 года назад

Sawset makes the most accurate joints,I've used all the other gauges and none are as good

@SawsetTools 3 года назад

Thanks for your comment. Accuracy is what we strive for.

@dmlvsccfamful 3 года назад

@@SawsetTools my clients are amazed at how tight my baseboards turn out even without any caulking

@SawsetTools 3 года назад

@@dmlvsccfamful I was a contractor and my son still is. Praise from a customer is always good.

@wvoyles 4 года назад

i do returns in a 3 piece joint,with saw at 22.5 degrees,and i use CA glue with an activator,looks a lot better than a 90 degree return

@SawsetTools 4 года назад

I like that look. Will try it sometime. Thanks

@billzima7068 4 года назад

I do mine same way. I did the 45° returns for so long and seeing the same thing in every house..i wanted a different look.

@SawsetTools 4 года назад

@@billzima7068 I will definitely try it next time. Thanks

@juanquintero3195 3 года назад

Great vid. What style, material, and how and size is the molding you are showing in the video?

@irisostachowski1489 3 года назад

We use a 5.5 inch wooden Georgian style.

@mattkoch1456 2 года назад

great tips thanks. looks like a small brad nailer, what guage/ length are you using and are you nailing into studs/ joists?

@SawsetTools 2 года назад

Hi Matt, Good questions. I used 18 Ga. x 2. (16 GA makes the perimeter of holes stick up) You try to hit the wood when you can. When gluing is done right, it gives a lot of support to the wood crown. (Keep in mind plaster crown moulding is neither nailed or screwed, yet it stays up.)

@raycarter575 3 года назад

what size nail gun were you using? great job on the video! i'll keep coming back!

@SawsetTools 3 года назад

18 Gage brad nails x 2 inch.

@albertocastillo1518 3 года назад

Saludos amigo

@thetoolman3355 3 года назад

Thanks Friend

@lordbyron4163 4 года назад

Question. Can you install crown mouldings over walls and ceilings that have wallpaper on? or do you have to cut the paper away first ?

@SawsetTools 4 года назад

Yes, remove wallpaper and wash off glue residue.

@toronto690 5 месяцев назад

What to do when the ceiling is not even, and the crown moulding titer totters? Which stud finder do you recommend. Need a reliable one

@jerrypelletier2328 3 года назад

I always cut crown holding the crown flat on my chop saw.

@thetoolman3355 3 года назад

See our other video. (How to Cut Crown Molding ON THE FLAT using Sawset Protractor.)

@bolerdweller 3 года назад

I do too. Most accurate way to do it

@rockyalford1622 2 года назад

Don't forget to tell them to turn molding upside down to cut

@SawsetTools 2 года назад

Good point.

@leeoien3645 10 месяцев назад

How about a short video on what to look for in a miter saw and other critical tools?!

@SawsetTools 10 месяцев назад

Something to think about. Thanks

@fredsanford6143 Год назад

Hello, Love the video. About to start a crown moulding install. The previous owner didn’t want to finish the crown, and stopped with a flush cut on an inside corner 3:10 3:10 . I understand it’s best to use a coping saw, but how do I cut the moulding and get it to matchup? Thank you

@SawsetTools Год назад

I know the traditional way is to cope, but mitering is the best way, because the 2 moldings lock each other in place. If the existing crown is not glued down, I would remove it and miter. Mitered corners are also crisper.

@squareheadconstructionllcf3327 4 года назад

I really need a sawset tool

@SawsetTools 4 года назад

You can order it from our website... sawset.ca

@anilpodgornik8206 4 года назад

Cicrular saws are limited.. You can only cut 7-10cm in heights, so when you come upon cornice mouldings that are bigger it is useless. There are hand saw kit for bigger mouldings. Simple ones for - 45 90 +45 degrees and also adjustable ones... For small or flat ones circular saw is much faster though...

@briangordon1767 3 года назад

Sawset tools I can't find any web site where they ship this tool to Ireland or UK can you please help me

@robertsoobramani202 4 года назад

What type of glue do you recommend for installing crown mouldings?

@SawsetTools 4 года назад

We have always used a water base glue, such as Lepage No More Nails.

@aaudain1 2 года назад

💯👍

@SawsetTools 2 года назад

Thanks

@sarahscarola4008 3 года назад

Any suggestions for a glue brand that would comparable to Lepage that is available in the US? Picked up Loctite All Purpose but it comes out as a foam and is very awkward to use.

@SawsetTools 3 года назад

Sorry, being in Canada not familiar with your product brands. Any product that are water based and paintable would be great.

@okalitoescalobi1529 2 года назад

Bud job to fill the nail holes with caulking.

@SawsetTools 2 года назад

My regret, wish I used compound.

@locatejohn 4 года назад

What's are your thoughts MDF and non-MDF crown moldings material?

@irisostachowski1489 4 года назад

Wood does a one time minor shrinkage, because of moister content in the wood. I use MDF, because doesn't shrinkage. Recommend oil prime before painting wood or MDF. This keeps moister away from wood.

@rodralph824 2 года назад

Great video. You might indicate which "glue" you are using.

@thetoolman3355 2 года назад

Hi Rod, We use La-page No More Nails. Any dense glue would work.

@artpaz738 5 лет назад

when you nail straight to the drywall ...always nail at an angle so the nails cant pull out

@thetoolman3355 5 лет назад

Good call.

@salvatoresaccoccio2379 5 лет назад

That doesn’t do shit. In time along with expansion and contraction it will pull away from the ceiling and wall. Test it with time and let me know the outcome.

@joseleal9134 3 года назад

I am stuck on one thing, when you show the tutorial at 5:14 you do not say how to cut the first piece you show in the tutorial. So basically the piece that you put that small little piece on. I do not know how to cut that piece so that the little piece fits perfect. Some help and clarification would be very helpful

@SawsetTools 3 года назад

Sorry Jose, in the editing it was decided not to create a long video. So I couldn't show every detail. Go to sawset.ca Videos and Tips. Look under Template and the piece you are referring to is the 5th picture.