How to install dimensional shingles on a roof and in a valley

Подписаться 5 тыс.

Просмотров 55 тыс.

50% 1

www.doityourselfdennis.com presents this tutorial how to video about how to measure, mark and install dimensional shingles on a roof with a priority of shingling a valley. Along with some tips on best practices. Disclaimer: In my videos I don’t always use the safest methods of accomplishing whatever the video is about. I have been doing this type of work for over 30 years and I try and show the average homeowner how to accomplish whatever job is at hand. Therefore, if you choose to do something I show in my videos, please use all safety precautions as I will not be held responsible for your safety.
Check out my other videos:
 • How to change a water ... How to change a water heater element
 • How to caulk trim befo... How to caulk trim before painting
 • How to Build a Soffit ... How to build a soffit and fascia return
 • How to cut and glue CP... How to cut and glue CPVC pipe
 • How to cut a hole in d... How to cut a hole in drywall for an electrical outlet
 • How to cut quarter inc... How to cut quarter inch Hardie Backer board
 • How to cut tile with a... How to cut tile with a manual tile cutter
 • How to Flash a Window ... How to properly flash a window before new window installation
 • How to enlarge an open... How to enlarge an opening on a non-bearing wall
 • How to get a good qual... How to get a good quality paint job on a wall with how to paint a straight line when cutting in
 • How to hang or install... How to hang drywall on a crooked wall
• How to install a doork... How to install a door knob and dead bolt
• How to install a Delta... How to install a Delta rough in valve using CPVC
• How to Install or Hang... How to install or hang Wire Shelving
• How to install a drain... How to install the plumbing drain for a washing machine in a remodel job
• How to apply alkali re... How to apply alkali resistant tape to concrete or Hardie backer board
• How to install a drop ... How to install a drop-in tub using concrete mortar as a support base
• How to install a pocke... How to install a pocket door in an existing wall
• How to install a solid... How to install a one piece or solid jamb door
• How to trim out a pock... How to install trim on a pocket door
• How to install a Vinyl... How to install a vinyl gable vent
• How to install a new c... How to install a new construction vinyl window
• Video How to install an Aprilaire humidifier with ductboard or fiberglass
ductwork
• How to Install Base Tr... How to measure, mark, and cut base trim inside corner using a coping saw
• How to install concret... How to install concrete board or hardi backer board on the ceiling and walls in a shower

Хобби

Опубликовано:

19 сен 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 77

@theresarodriguez3284 Год назад

I've seen other videos and starter pieces were nailed all the way around edges. Also nailing shingles, there is a keep out zone to prevent leaks; paying especially attention when shingle pieces are cut. Love this video vs. others because you pay more attention to measurements. thank you

@doityourselfdenniscom Год назад

Yes, some roofers put the starter shingles all the way around, and that is fine. As far as where to nail, dimensional shingles there is usually a nail line to go by. On three tab I nail about 3/4 of an inch above the notch in the tab.

@alimabraham744 2 месяца назад

Man you are the best love your details

@doityourselfdenniscom 2 месяца назад

Thanks, I try.

@joaoquiroz1243 2 года назад

You teach that way it should be taught, I've seen videos all they do show off really appreciate your patience and your time. Thank you From Greenville ga.

@doityourselfdenniscom 2 года назад

You are welcome. I try to take my time and teach what I think do it yourselfers need.

@seanjustg5425 2 месяца назад

Thank yas for sharing...appreciate good hard work. 💪💓

@doityourselfdenniscom 2 месяца назад

You are welcome.

@paulleftwich7753 Год назад

I appreciate your video, very instructional and not too much unnecessary confusing dialog

@doityourselfdenniscom Год назад

Thank you.

@raybrensike42 2 года назад

An advantage of buying starter shingles is that they have the tar strip low near the roof edge so when the shingle seals down, the wind won't be blowing up the bottom of the shingle. I've had to come back and put small galvanized box nails into the lower part of the shingles before because the wind did catch the first row of tabs and was blowing underneath them, because we used regular shingles as starter singles as shown @ 6:32 here. We did not cut off the tabs and put the shingle the other way .

@doityourselfdenniscom 2 года назад

Makes sense. I have never had to go back on a roof I installed. But, good point.

@carlodave9 19 дней назад

Good point. For some reason the starter shingles prescribed for my Certainteed dimensional shingles are super expensive. I think l’ll go with 3-tab starters and seal the things myself - only because my house gets hammered by autumn winds.

@burtburt1755 3 года назад

I learned a lot from this video. Watched the whole thing and only had one question and it was not part of what you were doing on this one. Which is best regarding the drip rail. On top of the felt or under the felt. I've seen both. Thanks you for taking the time to share your knowledge with others and also thanks to the nice lady doing the recording and helping with the chalk lines.

How to install dimensional shingles on a roof and in a valley

Опубликовано:

Поделиться:

Ссылка:

Скачать:

Добавить в: