How to install Easy Remap modchip PS5 DualSense BDM-010/020/030/040 

This video is gonna be helpful in about 3 years when i get my ps5

This man used his quarantine time wisely

This man said ‘easy’

Anyone worried about doing this, don't be. A very easy mod to do. Most difficult part is the soldering bit just take your time and use plenty of flux. As fir XQ Gaming, I can't rate them highly enough. Order mine and was with me in the UK very quickly. Spoke with Richard via email a number of times and found him really helpful. He helped me out a lot due to my stupid mistake of not taking my time. Just follow the video instructions and you'll be fine. End product works brilliantly. Thanks again to Richard for all your help, Steve 👍

Awesome. Get to do this tomorrow. Got the hammerhead on ebay

Finally a video on back paddles for the dual sense

I love your videos. How you show everything. Many German modders can learn a slice of this.

You sir deserve a salute....

props to anyone that had the stones to do this. my lazy ass is just gonna use the RISE Remap kit. i dont do souldering

THANK YOU!! I CAN FINALLY DO IT

Just got the PS5 can’t wait to do this.

Beautiful work. Excellent 👌👍

This is genius! I love the design. Going to do this for sure!

Just ordered some paddles to the uk! Look forward to getting them will keep everyone updated!

mine came in the mail today, just finished the glueing process one went well and the other had a few problems but finished now, I cant wait to play with them. I'm happy I stumbled onto this video

Bought it, installed it (took 30 mins), used it and love it!

Love your work again 😍

Nice man! I was looking forward for this one!

I’m going to give this a shot. Thank you.

I need this in my life

The order was processed within a couple of days and arrived in 2 weeks (as stated by the courier). You need a bit of “do it yourself” attitude but it’s not too complicated. 100% satisfied. I recommend 6x6x6 buttons for a crispier click

Made the process an easy one. I'm going to buy right meow

You're a freaking genius just wish I had the capability to solder haha

Got mine today, installation was easy following this guide, used double-sided tape instead of glue for the mod chip cable which gets pressed down by the battery anyway this seemed to make it a flat and less messy alternative and opens it up to adjustment if I ever want to change in future or utilise in a different controller

I just want to say thank you I have purchased and made my controller about eight months ago The only other problem I had which was the controller started to get stick drift so it was an easy fix all I did was buy another controller just swap it and just use my same paddles that I already made everything works phenomena

I’m in love ive been struggling with my Ps5 Without having paddles

I'm so glad I subscribed to you I click so fast when I saw this

found your channel through ifix it ps5 stick drift great content man def subbed.

thank god. all my ps4 controllers have back buttons (scuf vantage, astro c40, 3 modded ds4 with back buttons and ,2 with sonys official back button attachments) I'm happy to see how quickly some one put this out since Sony didnt make an offical back button attachment for the dualsense at launch

A video for smart triggers and bumpers on the dual sense 5 would be great!

Well. I just made it . The whole process took me 2 hours with mini breaks. I did exacly what he does in the video and everything went perfect . Have in mind that all the items are smaller than they look in the video , you will need soft hands for the soldering and good lighting . You have to make no mistake when opening the wholes for the screws because you dont really have many chances for the right placement . I strongly suggest plugging the controller in a pc and from control panel test that the buttons work .

That would be great if includes a chip to remap any button including L3 and R3…

I don't even have a ps5 and I'm excited about this lol

I love them

I love how you just handed out a a free scuf to everyone...and a business idea that would blow aswell. Wish u success bro

This looks cool

love the video i even subscribed, keep up the good work. one question for L1 R1 L2 R2 do they share same ground from other buttons

I reckon I could have managed it up to that flex board bit. You know it won't make contact and you'll he taking it apart over an over again stressed to death wondering why it won't work hahaha

Im gone order this as soon as i have the ps5

You can trace around the paddle with the marker instead of trying to align from the back. And then just use rubbing alcohol to erase the marker

Mantap stel stik psnya. Lanjutkan. Sukses selalu

I wish I could just pay this guy to do mines

Ordered mine... can’t wait

This is far beyond my capability 😭😭 great video though 👍🏼

Got my parts and analog sticks today all fitted, works amazing, got a soldering iron from screwfix an RU-vid'd how to use it. 🏴󠁧󠁢󠁷󠁬󠁳󠁿

Thank you!! Will you also do a video for buttons?

Merci pour la vidéo,

Cool video just what I needed, can you make a tutorial for 4 back paddles please?

I would definitely try this, but I only own the controller and not the system itself.

The most important thing you forget. Write on cable wich one is X and wich is O or you will have problems after u finish everything..

I like the idea, but I would rather connect to the L3 and R3 buttons.

Wish there was 4 back buttons

Just got my paddles like this video showed where they angle around the handles. I would give these a 9/10 as it takes a little playing with to get the paddle clearance right against the switches and now I can't use my dock anymore since the lower area where the lower screws are get in the way. When anyone is trying to mark the lower holes to drill make sure the upper screws are screwed tight so there's no play. And press your thumb near the lower screw hole so that you can apply pressure to ensure it's flat against the controller as you mark the hole. If you leave any play between the paddle and controller when you mark the lower hole to drill as you tighten the screws down it'll cause the clearance between the paddle and switch to change, and you may end up with more pressure on the switch or a gap. To fine tune paddle to switch clearance after the all holes are drilled simply tighten the upper screws first to almost snug then gently back out the slightest bit. Get the lower screws started and get them about 1/2 turn to a full turn from fully tight. It only takes the slightest loosening or tightening to get the paddle to rest a little more or less against the switch. And if you need to you can always gently bend/flex the paddle a tad but I'd rather just try adjusting the screws first. As for the sony dock issues I may take off the paddles and completely shave off that area where the lower screw is at, relocate the lower screws to near the indentation between both screw holes and that should give me enough clearance for the official dock. I figured I may run into dock clearance issues before I bought so it wasn't a complete surprise. Basically if you look at the area where the lower screw is at, if you form a circle around that stub you would remove that portion. Other notes: -When you glue gun the switches to the rear controller plate there's hardly any clearance for the internals when you put everything together. If you find the controller hard to snap back into place make sure your wires are tuck properly and take the hot tip of the glue gun to smooth out any excess glue that may be over the backside of the switch. I have all 4 edges of the switch hit by glue, but the backside of it is almost bare. I had to redo the left switch as the internals were putting extra pressure on it causing the switch to not move freely since it changed the resting angle of the switch, instead of being dead center in the hole I drilled it was binding on the edge of the hole. -When laying down the included PCB flex board I used hot glue over the top solder points rather than putting a dab underneath. It made sure the wires had more support to stay secured in place. Make sure you don't put too much or run it off otherwise you may run into issues where the battery holder doesn't lay flat. If you see the battery holder is crooked check the wires that they're not underneath the supports of the battery tray and make sure the glue is flat and not sticking up a lot.

well.. Elegant method...... but not for the beginner !!!

ahhh the music~

Would have liked to see you play a game right after doing this to show it working

Great tutorial thank you! I am wondering if you are going to do one for the new TrueFire-Flex Modchip (+Pro Remap options) you released as I currently have it in my basket ready to purchase but have no clue how to install it.

Yoo start a buisness building them, i would love to buy one from you

Great work, i just bought one of these. Are you going to do a tutorial with the paddles too?

WHY THE FUQ COULDN"T SONY JUST DO THIS FOR US lol Great Video! will be ordering everything today.

wow I would like a friend like you 😂

Nice 👍 💪💪

Would be cool to see a video of the mod actually working.

Making his own homemade scuf. Need him to make one for me

I'm not buying a ps5 until they come out with a back button attachment such like the ps4. Its essential with fps games for me at this point

Do you have a video where to screw the holes for the saber paddles ?

Is there any information about the L3 and R3 remapping for the DualSense controller? This is an amazing video but it would be great to know how to get that irritating L3 and R3 to back buttons instead of pushing down the joysticks.

업체가 아닌 개인이라면 정말 존경스럽다고 밖에 할 말이 없다. 물론 클릭감은 별로겠지만 그래도 저걸 손수 만들다니... was good!

Is there a video for how to install your new remappable mod chip?

Can u make a video on gravo tumbstick module is the Xbox one elite 2 controller tumbstick that u can use on any controller pls

I think I’ll wait for the official ones

Good tutorial. Why not have a template with the 4 holes?

can I just buy one from you lol. this is crazy

For the same mony i by a scuf

Hi there buddy great video 👍 looks awesome what’s the shipping time etc to the UK ?

What am I doing here I have a xbox and a elite series 2 controller but great job.

I'll be honest while this helps, I don't yet own a soldering iron, and I would prefer an installation option on the website, even if I would have to send in my controller.

mmmh, the only thing that worries me is the glue that holds the buttons in place, how durable is that gonna be?

The buttons work on the PS five menu but not in game

Only problemn I see is that there is no option to remap the only two functions I would want to remap. L3 and R3.

I think I might just start to play claw it’s to difficult

please do a video on the programable ones i want to buy but i need a tutorial, plus whats the difference between the +pro and the progammable only? txs

How in the world do I map the L3 / R3??

@XQGaming Thanks for the upload man, also what size switches would you recommend for the scuf size paddles?

Looks great. Sucks I can’t find US sellers but I’ll keep looking. How reliable are those tacts? They seem so small compared to the common others.

Can someone tell me if I hold the paddle will it continuously spam the assigned button or not?

Love the Shark paddle ergonomics! Just being a bit snobbish as someone who used to take apart and mod the shit out of fight sticks lol, as a fellow tinkerer, why such a deep button (the 5x5x5) Is the shell that thick? Also, is it possible to use a coarse threaded tiny bolt instead of the black screw so you can grab the back of it w/ some sort of lock nut on the inside? I don't trust the leverage I use paddles lol you think the screw won't degrade the shell over time? (although i do appreciate not completely cheesing it like the scuff nipple and dot style)

The glue on the button is keeping the controller shell from closing. Do I need to move the button? I tried scraping most of the glue off

Nice job! So clean! 👌👍👍

Are you doing custom paint jobs for duelsense controllers now. Also have you looked into the issues for drifting in the duelsense controllers?

Just ordered an AIM dualsense controller yesterday. Only downside to ps5 is no back buttons after 3years of using a nacon controller. Can't wait for my AIM controller to arrive.

Now I have a ? How do you remap the buttons do you have to Resorter the pcb or can you do it another way?

Why, you not sell the complete kit to ease purchase? I would like to purchase 1 kit for try, but is difficult to me to looking for the correct tool in your page.

Is it possible to add more than 2 back buttons to that

Does anyone have any input on the shark vs saber vs butterfly paddles? Close to ordering a few sets but having a hard time without feeling the different configurations on the dual sense.

Where do I connect the ground wire for the L1 L2 remap? I have 4 pin tact buttons. Do I only solder 1 wire to each button that's connected to the L1 L2 solder pad?

What is the red paste thing before he solders?

Can it be bought in a full kit seriously it will be a hassle for a noob like me who knows head nor tail.

Can you use superglue? I don't have a glue gun.

Does anybody know where i can find a ps5 controller with paddle assemble?