How To Install Peel And Stick Underlayment For A Roof. Sharkskin Ultra SA Synthetic Underlayment.

Подписаться 46 тыс.

Просмотров 9 тыс.

50% 1

Step by step instructions that show you how to install peel and stick synthetic underlayment for a metal roof. In this video we will show you how to install Sharkskin SA self adhesive roofing underlayment.
00:00 How to install peel and stick underlayment for a roof
00:50 Sharkskin Ultra SA installation and preparation
01:35 How to lay out self adhesive roofing underlayment
02:01 How to install peel and stick roofing underlayment at the valleys of a metal roof
02:29 How to attach peel and stick synthetic underlayment
03:20 How to overlap peel and stick roofing underlayment
If you already have not purchased your Sharkskin Ultra SA peel and stick synthetic roof underlayment, give us a chance to bid your job. Save 15% to 50% with our manufacturer direct
pricing and great customer service. Inexpensive delivery anywhere within the United States.
Visit Our WEBSITE
www.westernstatesmetalroofing...
Peel And Stick Roofing Underlayment - Sharkskin Ultra SA
www.westernstatesmetalroofing...
Visit our LEARNING CENTER
www.westernstatesmetalroofing...
Sharkskin Ultra SA is a self adhesive synthetic roofing underlayment. This eliminates the need for nails and caps. It does not require primer on the metal flashings.
How to install peel and stick underlayment for a roof
1. Clean the roof of all debris
2. Beginning at the lowest section of the roof, roll the peel and stick underlayment horizontally. Cover all parts of the fascia board that will be covered by trim
3. If your metal roof has a valley, it's best to run a strip of Sharkskin Ultra SA vertically along the center of the valley prior to installing the horizontal sections of roofing underlayment.
4. Remove the split back release liner and press the adhesive side into the substrate. Smooth out the roofing underlayment as you pull out the liner
5. Overlap the underlayment by four inches. Overlaps should run with the flow of water.
FOLLOW US ON SOCIAL MEDIA:
FACEBOOK: bit.ly/facebook-wsmr
INSTAGRAM: bit.ly/instagram-wsmr
TWITTER: bit.ly/twitter-wsmr
LINKEDIN: bit.ly/linkinin-wsmr
HOUZZ: bit.ly/houzz-wsmr
PINTEREST: bit.ly/pinterest-wsmr
RU-vid: bit.ly/youtube-wsmr

Опубликовано:

1 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 7

@davidmeier8860 2 месяца назад

I am on a 10/12 pitch and the framers want to nail toe-boards in due to the steepness.

@Californians_go_home Год назад

If installed in the cool season months, will it adhere enough without heat from the sun? In my case, I need to sheet and cover rows at a time. I am building solo and need adequate time in the open weather to fully sheet the building and also install the roofing. Parts of the roof may be exposed for several weeks. Should it be fastened in an alternative way under the circumstances ?

@yahelhernandez2422 Год назад

In cool season and windy for sure you have to put cap nails

@Californians_go_home Год назад

@@yahelhernandez2422 thank you.

@WesternStatesMetalRoofing Год назад

Hello. We have a video from Sharkskin that addresses Cold Weather ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-PUeJulmYDMU.html According to Sharkskin, Ultra SA is a non-asphalt adhesive, which is why it can be installed at colder temperatures. This is from their site: Sticks in the cold - down to 10˚F - without primer All temperature performance -40˚F to 280˚F It also has 12 months UV resistance. Hope this information helps.

@WesternStatesMetalRoofing Год назад

I reached out to the owner of Sharkskin, Mark Strait and this was his reply. Sharkskin Ultra SA® can be installed 20 degrees F and rising, and can be left exposed for 12 months. So, it doesn’t need sunlight to adhere. NO, Fasteners are not necessary. One more thing. We are a non-asphalt adhesive, which is why we can be installed at colder temperatures

@Californians_go_home Год назад

@@WesternStatesMetalRoofing thank you for the response. Very helpful.