How to Install the Ford Performance RIGID 360 Series 4” Round Ditch Lights - 2021+ Ford Bronco

Подписаться 2,2 тыс.

Просмотров 14 тыс.

50% 1

In this video I’m installing the Ford Performance RIGID 360 Series 4" Round Lights on a 2021 Ford Bronco.
Chapters:
0:00 - Intro
0:12 - Ford Accessories Part No
0:17 - Unboxing
0:44 - Hardware Installation
4:25 - Running Wires into the Engine Bay
5:27 - Wiring Installation
6:28 - Hiding the Wires
7:05 - Powering the Lights
9:32 - Turn On the Lights
9:55 - Custom Light Covers
10:16 - Outro
This is a fairly easy install, everything you need is in the kit, however I chose to add felt to the base of the mounting brackets to protect the cowl, and to paint the included hardware black.
I also used my own butt connector when wiring the aux wire as I crushed the one that came with the kit. (Always good to have in hand)!
Aside from that, very easy to install.
Here are the products I used:
Part No: M15200KBML
accessories.ford.com/products...
Here is a cheaper listing for the Rigid Lights:
amzn.to/3OsuHLV
Additional butt connectors:
amzn.to/3rrYVEz
Heat shrink tubing:
amzn.to/3rScwFN
Hope this video helps you out.
Enjoy!
#fordbronco #bronco #2021 #2022 #2023 #2024
Ford Performance Rigid 360 ditch light installation on the full size Ford Bronco.
NOTE: As an Amazon Associate I do earn a small commission from qualifying purchases.

Авто/Мото

Опубликовано:

7 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 76

@matthewbeauregard5057 Месяц назад

Just picked up a 2022 Bronco Raptor and couldn't find a thorough video on wiring for the Aux Switches until this one, it was spot on, thank you for this great install video.

@CUPRADESIGN Месяц назад

@matthewbeauregard5057 - Thanks so much for the feedback, glad that you found the video useful, and thanks so much for watching, I really appreciate it!

@Bass_city 4 месяца назад

These bronco tutorial videos are great!

@CUPRADESIGN 4 месяца назад

@Bass_city - Thank you, really appreciate it! So glad that you find the videos useful! I enjoy putting them together, so to get good feedback on them is awesome, thank you! And thanks for watching!

@Bass_city 4 месяца назад

@@CUPRADESIGN no problem!

@HipolitoJamilan 19 дней назад

Best tutorial videos I ever came across thank you.

@CUPRADESIGN 19 дней назад

Thank you so much, I really appreciate it. Means a lot and thank you for watching! Glad you find the videos useful!

@justincredible6851 2 года назад

Best install video out there. I used it for my Rigid pod light install!

@CUPRADESIGN 2 года назад

Thank you so much for the feedback, I really appreciate it! Glad the video helped and presumably your install went well too!

@davidlockebreaux8064 2 года назад

and those sasquatch decals look SICK!

@CUPRADESIGN 2 года назад

Thank you! I’m a designer and have the equipment, so designed and created the decals. Really pleased with how they turned out!

@emig911 2 года назад

@@CUPRADESIGN Great Job Cupra! Any chance you could make me some decals for my set of ditch lights? Ed

@emig911 2 года назад

@@CUPRADESIGN Nice decals, any change I could get you to make me a pair? Ed

@scottdulock386 Год назад

Fantastic video. Received my Rigid lights for Christmas and installed them using your instructions. It went well. The cowl was a bit of a struggle but was able to overcome it. Ford also should have given us more wire to work with for the switches. Thanks so much! Looking forward to more videos in 2023.

@CUPRADESIGN Год назад

Thank you! So glad you found the video useful, I really appreciate the feedback! I’ve got a lot more videos coming in 2023. Recorded 3 new ones today, just need to get them edited!

@mariomarez2223 2 года назад

I agree with Justin, best install video on RU-vid for this. You make it look so easy, but it won't be for me, hahaha. I will do it anyway, as my dealer wants 2 hours @ $150 an hour. Subscribed!

@CUPRADESIGN 2 года назад

Wow, thank you, I really appreciate the feedback! Believe me, it really is pretty simple. I did it differently to the Ford instructions in a couple of ways. I routed the wires differently, I chose to go under the cowl for a cleaner look. The Ford instructions want you to go between the fender and the door, but there's a lot more exposed cable and a chance of rubbing paint off the door. Secondly, they want you to ground each light on each side fender, instead of running the extensions across to one single point. That saved some time doing that as well. And hiding the wires under the cowl literally takes less than 5 mins, but makes the install look so much cleaner. Good luck with the install!

@tomclymore5800 Год назад

Great Video!!! I love the details of hiding all the wires. Very helpful for all of us with OCD.

@CUPRADESIGN Год назад

Thanks so much Tom, I appreciate it! Glad that you found the video useful! I just wanted to make the install look as OEM as possible. I did the same with my Oracle Triple LED Fog Light install video as well, trying to keep that OEM look! Thanks for watching!

@moreno6417 2 года назад

Seen many of these videos, this is the best one!

@CUPRADESIGN 2 года назад

Thank you so much, I appreciate it! I have more in the works!

@denniscampbell4783 Год назад

Nice work!

@CUPRADESIGN Год назад

Thank you, I appreciate the feedback. Glad you found the video useful, thanks for watching!

@mariacaballero9748 2 года назад

Nice work thanks for the tips on hidding the wires !!!!

@CUPRADESIGN 2 года назад

Thank you! I just wanted to make it look as close to a factory install as possible. So glad the video helped you out!

@Mgregoriosan 2 года назад

Great instructions and tips

@CUPRADESIGN 2 года назад

Thanks very much, I appreciate it. Glad that the video was helpful to you!

@gtasko1745 Год назад

great video dude.

@CUPRADESIGN Год назад

Hey thanks for the feedback, I really appreciate it. Glad you found the video useful. To answer your question, these were the first lights that I installed on the Bronco and they come with a 30A fuse. I hooked them up to AUX 2. I now have Oracle Fog Lights on AUX 1, a LASFIT Light Bar on AUX 3 and LASFIT Rock Lights on AUX 4 and AUX 5. I don’t have plans for anything high pull like a compressor or winch at this time. Also planning on quick disconnects so that I can just switch out whenever I want as I test new products. Hope that answers your question. And thanks for watching!

@mikeamerica0830 Год назад

Agree with everyone, great video & nicely explained. Appreciate the video.

@CUPRADESIGN Год назад

Thank you very much for watching, I appreciate it. Glad that you found the video useful! Just trying to help folks out as I install different products on our Bronco, making videos and sharing what I learn. I have a lot more videos in the works!

@alexagatep5939 4 месяца назад

Very nice presentation luvit am convince

@CUPRADESIGN 4 месяца назад

Awesome - so glad you found the video useful! You won't regret it, whether you go for the white ones OR the amber ones! The white ones are actually on sale right now: WHITE: amzn.to/43rVIqB AMBER: amzn.to/3IQS6oy

@tomanderson247 10 месяцев назад

Great presentation

@CUPRADESIGN 10 месяцев назад

Thank you so much, really appreciate the feedback. Hope you found the video useful. I have more coming all the time. Thank you for watching!

@twilsondallas 2 года назад

Need those decals!

@CUPRADESIGN 2 года назад

Ha! Thanks, just wanted to do something different rather than just the Ford Performance emblem on there!

@GaryMattson Год назад

great job, thank you

@CUPRADESIGN Год назад

Thank you very much, I appreciate it and glad you found the video useful!

@1SlimeyFukR Год назад

Thorough…thank you

@CUPRADESIGN Год назад

Thanks for the feedback, appreciate it! Thanks for watching and glad you found the video useful! More coming soon!

@davidlockebreaux8064 2 года назад

what was logic behind using the green/violet wire to which to connect lights? this is super helpful, thank you!

@CUPRADESIGN 2 года назад

I used the Ford Performance instruction sheet and that was the recommendation. Glad the video was helpful! I’ve got more videos coming! Here’s a link to the instructions: performanceparts.ford.com/download/instructionsheets/IS_M-15200K-BML_082721.PDF

@pat36a 2 года назад

The Aux switches have 3 different fuse/amp ratings, 1 30amp , 1 20amp and the rest are 10amp. Ford gives you a chart to match up the upfitter wire colors w/the switch. They also ran wiring to different areas of the Branco , the chart will give the locations.

@luyiPR 2 года назад

Hmm… about to install mines, but just noticed mine didn’t came with the washers. What’s size are those? Great video and instructions btw.

@CUPRADESIGN 2 года назад

Thanks for watching, appreciate it. Yes, my kit didn’t come with the washers either, so I just used a couple I had laying around in my garage. Unfortunately I don’t remember what size they were, as they were just random left over ones. I’m not sure why they aren’t being included in the kit as they are definitely mentioned.

@mattbanville9355 2 года назад

What colored wire do you suggest using for four of these? I have dual 360 pods with back lights. I understand I will run the back lights to a separate switch.

@CUPRADESIGN 2 года назад

If it were me, personally installing 4 of these, and not intending to use an AUX switch for any other high draw component, I would use either AUX 1 or 2. They have the highest rated performance and slightly thicker wire. But you can use any of 4-6 as well. This page gives a great guide to work with: thebronconation.com/how-to-use-the-auxiliary-switches-on-your-bronco/

@carlosmoreira9957 Год назад

Wondering if these would fit in my f150 raptor?

@CUPRADESIGN Год назад

Yeah, I don’t see why not. It’s a single bolt installation on the cowl. Alternatively you can purchase separate mounting plates if you want as well. I have a video showcasing some SevenSparta ones on my channel.

@moreno6417 Год назад

Any recommendation on where I can buy just the wire harness or which one? I got some lights but they didn’t have the wire harness

@CUPRADESIGN Год назад

Hmmm, you might be able to reach out to Rigid and see if they will sell the wiring kit separately. If not you might go to somewhere like Ace Hardware and see if they can match the wires coming from the lights.

@ericevil9633 Год назад

My bolts are just lose for the lights on the mount. There are fasteners but don't fit between them Edit after a few moments of pondering I realized you drop them in the plastic tabs that screw into the back of the light.

@CUPRADESIGN Год назад

Glad you were able to figure it out and get them to work. They can definitely be a little fiddly while installing. That’s what I showed two different ways of bolting them together. Thank you for watching, I appreciate it!

@kenlevengood9416 Год назад

Is it possible to make a sasquatch covers like yours but with azure grey lines for me , and how much. Thanks

@CUPRADESIGN Год назад

Thanks for watching the video, I appreciate it. As for the covers, I am not a professional vinyl company or anything like that, I just do it for a hobby. Due to the concave nature of those covers, it’s a really tricky install and it’s actually two layers of vinyl, so you have to do it twice in each cover. I’ve had several people ask for them, but I don’t want to end up being responsible when they don’t go on the covers easily and have to go back and forth with issues like that. Took me a couple of tries to get the ones I did right!

@kenlevengood9416 Год назад

Ok, but you did a great job on them.

@CUPRADESIGN Год назад

@@kenlevengood9416 - Thank you, I appreciate it and thanks for understanding!

@porschenineeleven7922 Год назад

How long did this take to install. Looks like 60-90 min?

@CUPRADESIGN Год назад

Thanks for watching, I appreciate it! To be honest, being as I record all of my installations, the time frame goes out of the window, setting up shots, recording, re-recording (and even re-recording again!) so it’s a tough call. However, thinking about the install, putting the lights together, if they are done off of the Bronco, and then mounted to the cowl, that’s about 15 mins. Then the wiring is about another 20-30 mins. I’d say about 45 mins total, an hour tops. Hope that helps, and thanks again for watching!

@jeffzerbe5623 Год назад

What felt did you use under the brackets?

@CUPRADESIGN Год назад

Hey Jeff, thanks for watching! The felt that I used was simply an adhesive backed sheet of felt that I purchased from Joanns Fabrics for about $1.25. Hope that helps!

@stevensimpson1043 Год назад

Switch 1/2 are both 30A, and 3-6 are 10A? Or do I have that wrong?

@CUPRADESIGN Год назад

Aux 1 is 30A, 2 is 15A, the rest are 10A. www.bronco6g.com/forum/threads/aux-auxiliary-switch-ratings-are-updated-from-previous-specs.26762/

@bluefe8545 Год назад

How long did this install take you?

@CUPRADESIGN Год назад

Being as I was recording the installation I don’t have a clear time it took, due to the nature of recording it, moving the camera etc. However, it should take only 30-45 mins. Hope that helps!

@bluefe8545 Год назад

@@CUPRADESIGN thanks a lot!

@CUPRADESIGN Год назад

@@bluefe8545 - No problem, always happy to help!

@ValerieWarner1 Год назад

What stubby antenna is that?

@CUPRADESIGN Год назад

This is the original antenna I purchased: amzn.to/3C61RfC Then the second antenna I have on my other videos is this one: amzn.to/3YPWiM2

@ValerieWarner1 Год назад

@@CUPRADESIGN thanks homie

@CUPRADESIGN Год назад

@@ValerieWarner1 You’re so welcome!

@supermike0822 Год назад

Okay, first... thank you. Your video was very helpful in my installation of these lights. Second... I'm not a novice to auto electric, but... what a freaking pain in the @ss! Installing the lights was fairly simple, though the screws they give you are somewhat lacking. And it would have been nice if they'd thrown in a cheap hex key. But the wire CONNECTORS... holy hell. I don't know how you made it look so easy in this video, but twisting two wires together as tightly as possible and then trying to fit them into the connectors DID NOT WORK. They were too thick. WTH. I used a different kind of barrel connector and ring terminals, but it was very frustrating. Also, would it have killed Ford to give us a few more inches of wire to work with on the AUX switch connectors? Finally, shoving the taped wires under the cowl was NOT easy... it barely fit. If I had to do it over again I'd have run it through some techflex sleeve or split loom and zip tied it to another wire. Freaking heck.

@CUPRADESIGN Год назад

You are welcome, glad you found the video useful! In the video I used my own butt connector, as you said I found the ones provided a little small for the job. I did use the ring connector provided, that worked well. I agree with you on the AUX wiring as well - that would be nice if there were a few more inches of each to play with. What if the first connection doesn't work and you have to cut it off... you are then getting real close to the firewall. I honestly didn't have an issue running the wires under the cowl, in fact that's a reason I suggested it, as it wasn't a challenge. Sorry to hear that you didn't have the same experience there. Thank you for watching, I appreciate it!

@supermike0822 Год назад

@@CUPRADESIGN Thanks for the reply! And I did manage to get it under the cowl, so it’s hidden, but I fear I’m stressing the clips a bit. Time will tell. But overall they look great and work, and I followed your advice on not running them through the door as Ford recommends. I agree that’s a much cleaner look. Again, I appreciate the helpful video! (Side note to add - I was disappointed to learn the Ford Performance version of these lights do not have working backlights. I was hoping they did.)

@CUPRADESIGN Год назад

@@supermike0822 Of course, I actually try to reply to everyone when I can! That's great that you managed to get them hidden under the cowl. It does look a lot cleaner. You might look and see if you can poke the wired a little further under the cowl, it kind of has a 1 inch lip at the front and when you get the wires past that, there's a lot more space for them. Might be worth a look, if I remember rightly its only like 6 clips to pull up - especially if you're worried about stressing them. And yes, the Ford Performance ones are the 'basic' design, but have the wiring harness included to get them set up with the AUX switches, (and the custom 'Ford Performance' covers - which as you saw I covered up anyways!), the RIGID Lighting version of the same style of lights are available with different colored back lighting, but don't have the Ford covers, and don't have the specific wiring kit for the Bronco with them either. I had looked into this before buying them too.