2021 Ford Bronco Rigid 4in 360 Series LED Pod Light A-Pillar Install into Factory Accessory Switch 

Yeah, ditto, I thought the same thing, why use the huge amp wire for something like those lights? I have used my switches 5 & 6 for lights. I do like their videos, I've seen a few others.

I was thinking the same thing until I started wiring my own saw that the four 10a wires are only 22awg. The upper two are only 16. To each his own, but I would never use 22 to carry even low power more than a foot or two. May look at the relay box and see if those can be replaced.

Thank you!

Eh, you shot it at where the crimp is so you would only lose 1/8" of wire each time. I get the thought, but a weatherpak connection there is a bit overkill. There is also more wire than it looks like, or at least there is on my SD anyway.

That is a good idea. Maybe we will implement that when we add a light-bar and move the pod lights to switch 2 and light-bar to switch 1.

May be a dumb question, but I’m not a wiring guy. Using a weatherpak, would you be able to crimp both of the wires into the one, using the single weatherpack connector? Hopefully I’m not complicating this question.

Do these have the amber backlight option?

:45 Screenshot

Yes, you still have to wire the ground to the frame. Luckily there are lots of factory locations to do so. Thanks for reaching out!

These are The Rigid 360 Series 4 Inch Round Lights

Do they have the amber backlight option?

I think they should still be listed with Ford Accessories. We can get them ordered for you if you would like, just let us know. In regards to switch we picked. We did the 1st switch due to connivance currently. Once the light-bar comes in we will most likely change which switches each lighting group goes to.

you can always change the preset fuses in the box to acomidate what you need... you can make switch 2-6 a 20 amp

@@PrtTymPimp1980 Each AUX switch has a different gauge wire intended for a specific amperage. Switch 1, yellow wire has a 1.5mm wire gauge and corresponds to the 25A fuse. AUX2 is 1.5mm with 15A fuse, AUX3 is 0.75mm and 10A fuse, AUX4 to AUX6 are 0.35mm and 5A fuses. I wouldn't recommend what you're suggesting.

@@2011blueman Hey, thanks for that note on wire gauge. I was unaware of that and its important we understand (still waiting o my Bronco so haven't looked hard enough). But that begs the question on what we can use with those smaller wire gauges on Aux 4 to 6. I would think small lights like these should be for the smaller diameter wire but are these last 3 switch gauges to small for dual offroad lights. if so, what else is there that they could be useful for. Maybe pod under body lights I suppose. Guess I need to figure out what gauge and fuse the components recommend and start there.

@@MiddletonMotorsports I just ordered two sets of these pod lights but they have a back light. Do I need to wire the back lights to a separate switch? My Lightbar will also have a back light.

Yeah that was from transport damage. Got fixed by the transport company.

ive been using 14g on our Bronco... light bar and 7" Hella pod lights on the side.. The one thing that is left out of this video is that Ford put the wiring diagram in the "infotainment" screen....it is the general settings...

The ford accessory kit part number is M-15200K-BML. It comes with the brackets, Rigid 360 series 4'' light pods, wiring, bolts, and "ford performance" light covers. One important thing to note is that the ford version of the Rigid 360 lights disables the backlight feature that is normally on the rigid 360 lights. Normally the 360 lights have a backlight available in various colors.

@@2011blueman thanks for that update. If only we could get that better bracket he used here with the standard Rigid Pod Lights (with backlight feature). I bought the latter with the chrome cheaper bracket and it doesn't give me enough play to get the light away from the antenna. I need to find another bracket, or modify the current ones, to move it back and to right an half inch or so. Those Rigid Brackets also need to be painted. Looks terrible against the black base and mirror area.

@@panzer948 Since the bracket is sold in the kit, I'd bet at some point you could get it from either ford or rigid. I'd contact Rigid customer service and see if they can sell the brackets separately.

@@2011blueman good idea. I think I will shoot them an email shortly (since it's Sunday).

Gary, I thin those decals come standard only on the first edition. I could be wrong.

@@paepae6199 Gotcha...I did find a link to a website that seems to sell some nice decals...I may go that direction. Thanks!

Transport damage