How to Lay Out and Square Metal Roofing Panels

Подписаться 42 тыс.

Просмотров 67 тыс.

50% 1

How wide should your first metal roofing panel be and how do you make sure the rest of the panels are square going across the roof?
**********************************
Installing your first metal roofing panel on a project isn't as simple as fastening any panel onto the deck; it takes preparation. Today on The Metal Roofing Channel, Sheffield Metals Weathertight Warranty Inspector Jason Ayres details how to lay out your panels based on flashings, penetrations, desired look, and more. He also uses formulas and practical examples to explain how to install panels square and uniform across the entire roof.
Topics Covered:
►Intro 00:00
►How to layout panels 3:06
►How to square panels 5:02
Always remember to follow manufacturer's installation guidelines.
Please note the installation details and methods shown in this video are for reference only. Sheffield Metals recommends following their published installation details or for WTW projects following the required details issued and marked approved for that specific project.
**********************************
FOLLOW THE SHEFFIELD METALS TEAM
► / sheffield-metals-inter...
► / sheffieldmetals
Visit Our Website: hubs.ly/H0bFCn60
Subscribe To Our Blog: hubs.ly/H0bFYvX0

Опубликовано:

4 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 31

@SteveThompson-li2fc Год назад

Here in the historic parts of New Orleans the roofs are NEVER square. I skip all the remedial math exercises and place one panel at one end of the roof slope, then another panel at the other end, straighten them up, pop a chalk line and rock&roll. Works for us.

@stevenwoodard1886 Год назад

Awesome content and just what I was looking for. I am starting a new cottage build in the Spring of 2023 and will be using a metal roof. Most of the build I will be doing myself with a few friends who have already built their own cottages. Excellent points. Cheers from Canada

@chriskisloski7424 2 года назад

What would you do when you're working with an existing roof that is already out of square?

@tomb1734 3 года назад

Nice job!

@geraldkurkjian2922 3 года назад

Have u got any light steel framing videos?

@JoseCruz-gm6eu 3 года назад

When if you multiply the decimal and you get 5.994 do you round up or not, I’m not really sure what to do?

@ljacksonroofing 2 года назад

Nice

@brk49er 2 года назад

What about when dormers are in the way of squaring up?

@iamtheman7018 2 года назад

when the guy at one end of the panel is pushing too tight and you aren't checking that's fun. as for penetrations typically we would have them relocated them if possible

@charlescardenas261 3 года назад

How do you seam when it is say 6" from the side of the chimney and the panels terminate against a brick wall? With hand seamer, i.e. 180 dble lock? The chimney is in center of roof, so seams are to the left & right side. Thanks Charlie

@jeffboyardi 3 месяца назад

I remove the outside screw from the handles of our hand seamer and leave one in loosely so I can pull the handle down or up and use multiple short passes. hope that helps

@BrianBaldridgeC 3 месяца назад

Got it, thanks Thad! 😊 Now, what does it look like to install the penetration after the roofing is installed? I can conceive it in my mind, but that doesn’t mean that’s how it should be done. Do you have a video on that?

@TheMetalRoofingChannel 3 месяца назад

Can you elaborate a bit more? As in the panels are already on the roof and you need to put a pipe through them? -Thad

@BrianBaldridgeC 3 месяца назад

@@TheMetalRoofingChannel, the question is pertaining to the information shared at 9:37 - 10:05 in this video.

@TheMetalRoofingChannel 3 месяца назад

@@BrianBaldridgeC I see! My interpretation of his explanation there is that as you're paneling across the roof, wait to cut the penetration in the deck until you see where the panels will lay. That method is really usually only necessary for large commercial roofs where you can't measure from the end of the building. -Thad

@BrianBaldridgeC 3 месяца назад

@@TheMetalRoofingChannel, got it! That makes sense, thank you Thad!

@Brandon-no3vc Год назад

how do you stretch and shrink it and keep it streight do yoi ever have 2 cut the rakes?

@jeffboyardi 3 месяца назад

if you need to move the top side of your panel towards the gable, you c-clamp the panel to the lowest clip and toe-nail a screw in the top of your panel until you've stretched it enough. attach all your drag loads then replace the toe-nailed one last to keep tension. if it's the bottom of your panel, you clamp the top side to the previous panel and let the bottom float. you can also give it a tug if you need but it's a marathon not a race.

@littlemanoo 3 года назад

This guy is great!👍🏼

@MrNiceGuyMEGA08 2 года назад

I prefer to move the pipe slightly left or right than have it come up on a rib amd looks better.

@TheMetalRoofingChannel 2 года назад

Moving the penetration is a great solution as well! -Thad

@kenmcf 3 года назад

What is the roof is not square...do you "trim" or adjust the first panel, and then go from there...and what if other end(rake is not square)

@7ovinadventures916 3 года назад

You may have to cheat your panels. And depending on the product you’re using yes, because there’s many gable end flashings that will cover your messy out of square house provided it’s no so crooked that you can notice the corrugation lines going to far in or out on the gable edges

@kenmcf 3 года назад

@@7ovinadventures916 luckily I could not get panels shipped in time for what i needed...so i cancelled...and did a torch down roof. Not as pretty, but solid, and cheaper!

@kenmcf 3 года назад

I hired a guy. I was curious how he would approach the "paralleogram" type roof I had....he just lined all strips up with the eave...and then trimmed on the back end...although the strips went "east to west" vs north to south...anyway..it looks pretty normal.

@davidking4139 3 года назад

They don’t go over lining up ribs

@jorgelozano435 3 года назад

Enseñe en español pliss

@TheMetalRoofingChannel 3 года назад

¡Gracias por su surgerencia! -Thad

@ISMERETTENGER 3 года назад

It stops playing at 4:49.

@charlesviner1565 Год назад

👍📐

@acoustic4037 3 года назад

I'm getting so tired of abusive amount of ads in every video. I'm going to Simply watch all videos using a browser with an ad blocker. Is everybody so terribly broke that they have to the excessive with the commercials? Or am I just the stupid one who doesn't know that it can make you a millionaire or something?