How To Make A Spinner Ring Using Durston's Spinner Ring Flarer Tool

Подписаться 137 тыс.

Просмотров 34 тыс.

50% 1

#andrewberry #spinnerring #durstontools
In this film Andrew Berry shows you how easy it is to make a flared edge ring that can be used to make a spinner ring using the NEW Durston Tools Spinner Ring Flarer Tool.
The tool enables you to flare both edges of the ring evenly both at the same time. So much easier than other tools out there on the market.
To buy yours, click the affiliate link below.
durston.com/product/spinning-...
/ atthebenchuk
/ at_the_bench_uk
/ andrew_berry
THE EQUIPMENT I USE TO VLOG AND FILM
Epidemic Sounds www.epidemicsound.com/referra...
Canon 80D, Body; amzn.to/2Lfkdk7
Canon Lens 10-18mm; tinyurl.com/gncnrwz
Tripod for Canon; tinyurl.com/hdhuz6z
Memory Cards; tinyurl.com/z8mhuk4
Card Reader; tinyurl.com/z97tccx
Microphone, Cheap; tinyurl.com/hbxtthg
Microphone; tinyurl.com/zpjpoeq
Canon G7X Camera; tinyurl.com/jkvu4b4
Tripod for G7X; tinyurl.com/z27m9aj
Mini Tripod; tinyurl.com/he93omu
Mavic Drone; tinyurl.com/jfh9da4
360 Camera; tinyurl.com/jbmrugq

Хобби

Опубликовано:

17 ноя 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 68

@jeannettesalazar6442 9 месяцев назад

Andrew you are the best lecturer, I ❤ your work and your transparency. The other videos with Louise are to confuse for me because they made questions that I don’t understand what they’re talking about. I am learning from you at the bench tutorials. I am addicted to your videos. Thanks ❤😊😊😊😊

@wendyannh 3 года назад

Clever little device, clearly intended for tool junkies, LOL! Actually, though, as an apartment-dweller, this would really help me and *allow* me to actually make these rings, because the less hammering of any sort I have to do, the better. Don’t want to piss off the neighbors, or the landlord, with that noise! Another nice video, Andrew, thanks. I like your new back wall, too.

@sdtuber1099 3 года назад

Thank you Andrew. An ingenious tool & helpful demonstration. Glad you are resolving the number of ads.

@beaddemon2572 3 года назад

Can't wait to try mine. Would it be possible for you to do a video sometime about soldering a textured ring and how to handle the cleanup of the joint? Maybe give us some tips in how to avoid major cleanups on the joint of a textured ring? This is still an area of growth for me. 😂

@moorejl57 3 года назад

This looks like a nice way to make a crushed stone inlay ring as well. The inside of the ring is basically a comfort fit and the outside concave area can be filled with inlay and CA glue.

@dawnsaffel2620 2 года назад

I can't wait to try this style ..your videos are so good and informative. Thank you ! I'm going to look at getting one of those flare tools.

@wormemc 3 года назад

Just got my flaring tool but I'm getting an uneven flare on my rings

@gilliansprott5487 3 года назад

Great to see how easy it is to use.

@lorraine8368 3 года назад

Great video... as usual!👍

@evgenishenker752 2 года назад

Thank you a lot, very detailed and understandable.

@Orandu 3 года назад

I’ve been using a plumbing flare for years. This looks so much easier!

@msackettcna78 2 года назад

Thank you! Great vlog!

@elisazulueta9535 Год назад

Thanks great video, ingenious tools to make spinner rings ❤as always your the best teacher ❤

@VMHenning 3 года назад

Thanks for demonstration! Just ordered this from Durston (with your code) and l’m looking forward to make some curved rings with different textures.

@debbiedenyer3797 Год назад

Your teaching makes sense

@mary-annkieckhaben5026 2 года назад

Thank you for shering look good.

@dawnsaffel2620 2 года назад

Hello Andrew I bought the Durston spinner tool. But I am not getting an even flare. One side will flare and not the other. Can you tell me what I'm doing wrong.

@zuma3334 7 месяцев назад

Hello were you able to figure out why it didn’t flare evenly? I noticed he did not text you and others back

@dawnsaffel2620 7 месяцев назад

Hello @zuma3334 no I actually have not used it since. But I have some people who want me to teach them. So I guess I will be trying it again.

@ozelgriffin 3 года назад

Super happy about this tool! I would like to know where can I get the chart for the ring sizing?

@deputydog1995 3 года назад

I like your sparkly spinner spanner.

@wendyannh 3 года назад

😆

@George-ew3gx 3 года назад

That is a neat tool. You have great videos ,thank you. I know this is off the subject of spinner rings but how would you temper a silver tie bar 5mm wide 18ga? Thanks in advance. George

@mmukherjini2161 Год назад

Thank you…I did get the flatter but haven’t tried it yet…you make it look so simple..it’s always the soldering which scares me 😱

@mmukherjini2161 Год назад

Flarer

@oreolovesyou95 Год назад

Awesome video! Do you hav any tips/can you make a video on how to clean a seam of a textured ring? i never seem to get it right and always sand off the texture :/

@teanpascoe8481 3 года назад

Hello :) Where did you get your ring size table from? Thank you, Tean

@stephenjohnson1221 3 года назад

you can all so use it for flesh tunnel earrings.

@JoeyisDREADful 3 года назад

Good point.

@bethcramer3420 3 года назад

How do you get the spinners on the ring?

@christieread9506 3 года назад

Andrew I got one of these from your 12 hour marathon ( brilliant day) but it doesn’t flare evenly for me, any ideas where I’m going wrong?

@zuma3334 7 месяцев назад

Hello, Were you able to find out why it didn’t flare evenly? I noticed he did not text you back. Thank you

@althealawrence9240 3 года назад

Great video as per usual Andrew :-) Is there a separate video on how to make the actual rings used as spinners?

@Atthebench 3 года назад

No but I can do one if you like?

@althealawrence9240 3 года назад

@@Atthebench Yes please👌🏽

@Nrscathy60 Год назад

I've seen many solder videos, but what is the grit of your emery paper and what is your buffing stick, leather??

@Atthebench Год назад

I only use 600 grit and I use it wrapped around the wooden stick

@SilvernStone 3 года назад

Any chance of getting the discount offered on the marathon? I couldn't order then due to the overwhelming response and the computer crashing and have been too busy to think about ordering it since then.

@Atthebench 3 года назад

The offer ended on Monday I’m afraid.

@tahomyjo 2 года назад

I wasn’t clear on what gauge silver you used for the band? You said not point eight? I don’t understand? Is it 0.8 ?

@tahomyjo 2 года назад

I figured it out it’s 20 gauge

@teresas.3979 3 года назад

Now I have a bad case of the I wants it.

@SilvernStone 3 года назад

Would this tool work to make a coin ring?

@dhduncan Год назад

Can I use a butane torch for hard solder?

@Atthebench Год назад

yes of coarse you can. Its what i use for making the initial ring with.

@dhduncan Год назад

Thank you! I don’t have any of the gas torches like mixed gas ones so this is a big help

@a1jaspertint461 2 года назад

Do you make these to sell ?

@Atthebench 2 года назад

DURSTON.com sells them

@ausrabernote5914 2 года назад

@LightKatchurs 3 года назад

so you made this flair do-hicky??? I thinks that's what I read! Call Rio Grand here in America! I wanna get it! and support your brain!

@peterrschuck 4 месяца назад

Nice idea, but shipping is way too high to purchase. Given no options other than high price, which is a similar price to the device. Was going to order one but cancelled it once I saw the shipping price. Will look in the hardware store for something similar in the plumbing section. Sorry, Andrew, but we purchasers should be allowed to select cheaper shipping options, not high priced cone only DHL Expedited. I don't mind it taking some time to arrive here in Australia.

@Atthebench 4 месяца назад

Sorry Peter. But with so many parcels going missing we have to have a method of tracking and claiming our money back

@peterrschuck 4 месяца назад

@Atthebench no problem I totally understand. Just a little disappointing to go through and find such high pricing for shipping. It's not the first time I've had to cancel a prospective purchase.

@katherinesolo3939 3 года назад

so so many ads,is that normal?

@Atthebench 3 года назад

Thats RU-vid doing that, not us. Will sort it out

@katherinesolo3939 3 года назад

Still love your channel, keeps us all sane during lockdown.

@dawndeluca 3 года назад

Should have been titled How To Make a Flared Ring. Would have been better to see it flare with the spinners on. Disappointing.

@Atthebench 3 года назад

Sorry that you find the film disappointing. I did show you a couple of the spinner rings and clearly demonstrated how to make the ring if I had added them. I felt it better to show the flaring action and the movement of the metal using the tool. If the spinner rings were in place you wouldn’t have seen the flaring very easily.