No video :(

How to Make CNC Clampdown Wasteboard | ToolsToday

Подписаться 1,1 млн

Просмотров 109 тыс.

50% 1

Watch the short version here, • How to Make CNC Clampd...
A high-quality work holding wasteboard, like this one, is one of the best upgrades you can make to your CNC. Watch along as I use my Amana Tool® line of CNC Router Bits in my STEPCRAFT D.840 CNC Machine. www.toolstoday.com
Sized out for the STEPCRAFT D.840, but may be modified to fit smaller or larger sized CNCs.
This wasteboard is designed to use cam clamps to hold your work piece against the fence. They hold from the side of the work piece, making the top of your material free of any clamps. It uses .-20 t-nuts and can also be used with top hold down clamps using the same size bolt.
Buy the plans to make your own CNC wasteboard here www.toolstoday...
Tools Used in Video:
Amana Tool 55227 3/8” Dia Carbide-Tipped Countersink with No Burning and Marring Adjustable Free Spinning, Low Friction Depth-Stop with No-Thrust Ball Bearing. www.toolstoday...
Amana Tool MR0110 Miniature Corner Rounding with Mini 3/16” Diameter Ball Bearing Carbide Tipped Router Bit
www.toolstoday...
Feed, Speed, Chip Load & Step Down CNC Running Parameters
Amana Tool 46202-K 1/4" Dia. x 1/4” Shank Solid Carbide Spiral Spektra™ Coated Down-Cut Router Bit
tinyurl.com/am...
Feed Rate (IPM): 180
Speed (RPM): 18,000
Chip Load (Per Tooth): 0.005”
Ramp Down IPM: 90
Amana Tool 46315-K 1/4" Dia. x 1/4” Shank Solid Carbide Spiral Spektra™ Coated Up-Cut Router Bit
www.toolstoday...
Feed Rate (IPM): 180
Speed (RPM): 18,000
Chip Load (Per Tooth): 0.005”
Ramp Down IPM: 90
Amana Tool RC-2265 CNC Spoilboard Insert Carbide 3 Wing x 1-1/2” Diameter Router Bit
www.toolstoday...
Feed Rate (IPM): 100
Speed (RPM): 18,000
Chip Load (Per Tooth): 0.001”
Ramp Down IPM: 50
** Subscribe - / toolstoday
** Shop the website - www.toolstoday.com
** Like at Facebook - tinyurl.com/too...
** Follow on Instagram - / toolstoday
** Follow on Twitter - / toolstoday
More Links
STEPCRAFT D.840 CNC Machine www.toolstoday...
Amana Tool® www.amanatool.com
Buy the plans to make your own CNC wasteboard: www.toolstoday...

Опубликовано:

20 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 73

@protect.your.digits.creations 3 года назад

Great video Matt , but then again I learn from all your videos .. Those bits are like cutting butter with a hot knife .

@ToolsToday 3 года назад

The Amana Tool line bits are super sharp - yes! Thanks for watching.

@jameszeman2628 2 года назад

Just recently started buying from you guys and am super impressed. ToolsToday is the first place I go for stuff for my shop now. My current CNC needs a friend, and I'm considering the Stepcraft 63x108.

@ToolsToday 2 года назад

That's awesome, I'm glad to hear that! Thank you for the support. If there's anything we can do to help, feel free to reach out!

@chrisdavisunofficial Год назад

I made the same set-up for my Shapeoko and it saved so much time on repetitive work. I highly recommend this for any CNC router.

@jessefoulk 2 года назад

A really well done build. Better than what I could've drummed up. I have the 600 size version but that's really all I was looking for. After seeing this video I know I have to implement some of these for my board.

@Shadypoolguy 3 года назад

I’d like more videos on this machine. Interested in upgrading from my shapeoko!

@ToolsToday 3 года назад

We will definitely have to do a comparison video here soon!

@wellsjulien9255 3 года назад

Nice speedy pace, well done

@ToolsToday 3 года назад

Thank you! Cheers!

@Thefarmshow 3 года назад

Really good video, I was trying to figure out what to do differently with my table, this is the best I have seen yet! I like the wedge clamps

@ToolsToday 3 года назад

Thank you very much!

@Coolarj10 3 года назад

Great vid!! Can’t wait to download the plans and try this out!

@tonybowen8519 3 года назад

instablaster...

@thefulchman 2 года назад

I love your videos. I really want a Stepcraft after watching some of these.

@Stoneforth 2 года назад

I like the t nuts, but i just drew up a grid with a pencil and drilled them all out by hand. No cnc pockets just sandwich the tnuts between the top and bottom board and screw together then surfaced the wasteboard.

@georgekenner6588 3 года назад

You made it so simple.

@mtz3843 3 года назад

that looks like a great machine, wish i could afford one, wow

@pmsilvei 2 года назад

Build one! It's a lot cheaper and maybe you'll end up with a better machine.

@mtz3843 2 года назад

@@pmsilvei never thought of that

@mickeymallette2663 2 года назад

Watching a lot of your CNC videos. Great stuff! What would you suggest to a newcomer who wants to learn the software side a little before buying a machine? What programs are used in woodwork CNC?

@leonardcarroll156 Год назад

Nice job. I bought the plans. But Can you make a video to show how to set the uccnc to the xy corner position and save the position in uccnc as a macro .

@CarlKorschgen 3 года назад

Thanks. Nice job

@alterstassfurter5743 2 года назад

Clever done...respect !

@ToolsToday 2 года назад

Thank you!

@fredscott413 3 года назад

great show,thanks.

@ToolsToday 3 года назад

We're glad you like it!

@thorpie2206 3 года назад

Dude looks straight out of GALAXY QUEST! hahahaha But in all seriousness, love the channel and content. 👍

@ToolsToday 3 года назад

Thanks so much we will continue to make videos for you and our subscribers!

@nanoblasting 3 года назад

thanks 👍

@ToolsToday 3 года назад

No problem 👍

@vassillemopp3237 4 месяца назад

what causes my bit to make burr on material? most times my bit is sharp enough,or do I plunge too deep?

@johnmalkin8210 2 года назад

What do you do once you've resurfaced your board a few times? Do you knock all the t-nuts out and redo it all over?

@bonarlibor3067 3 года назад

Awesome man

@klave8511 3 года назад

Great video, lots of work putting all those nuts in! It want clear from the video, it looks like the screws that hold the fence down are a very loose fit, how do you get it properly square when you refit it?

@MrRuizi 3 года назад

Muy buena idea!!

@ToolsToday 3 года назад

Gracias!!

@leejackson3781 2 года назад

HI. Great video. Does the fence take away from your available spoilboard area?

@IjoDaun34 3 года назад

I like this video conten . Whether in Indonesia there is this machine too , sir?

@IcanCwhatUsay Год назад

3:51 it's definitely NOT square. 😕What gives?

@PavelBartko Год назад

Hi. What real working speed does this machine reach? Sliding speed in turnover.

@darrinking9210 3 года назад

Help me out here I am new to the woodworking world, what does a waste board do?

@ToolsToday 3 года назад

The wasteboard is essentially what you cut into when you cut pieces out. It protects the machine bed. This one has workholding solutions built into it making it super functional!

@timberwolf1575 3 года назад

When you make any cut through the full depth of your work material, the tool has to go just a little bit further through the material to make a clean cut. For mills with flat bottoms, the penetration can be very minimal, for pointed or rounded tips, it has to go further through. Your waste board is there to sacrifice itself instead of having your tools go into the work table. Presumably the work table is flat, smooth, level, etc. and you want to keep it that way.

@sergioivantrujillo9184 18 дней назад

Tengo una CNC M1000 y no encuentro videos en español ,por favor alguien que me pueda guiar

@jgc25gomes83 Год назад

Parabéns! Onde consigo o desenho do grampo!?

@abdulwoodudlike2know3 3 года назад

Good morning, how is your waste board attached to the cnc table itself? Does it already have screw holes on the surface?

@ToolsToday 3 года назад

It is screwed to the stock wasteboard and countersunk well below the surface using the 55227 No-Mar countersink.

@abdulwoodudlike2know3 3 года назад

So Step Craft comes with an MDF stock waste board?

@abdulwoodudlike2know3 3 года назад

I have Next Wave shark, but it has the aluminum bed. Just trying to figure a way to use that hold down concept. I like the convenience of it.

@abdulwoodudlike2know3 3 года назад

Any suggestions? Oh! I enjoy the videos, and I like how you keep any mistakes in the video and just explain what happens. To many times we see videos, but don't know about the booboo's! I think they are important too, if for no more than preventing someone else from making the same mistake. Keep the videos coming.

@ToolsToday 3 года назад

@@abdulwoodudlike2know3 Thanks we like to show how it really happens.

@woodfantasy871 3 года назад

Hello! i can't find the plans. Is anything wrong?

@wilsonpierre1123 2 года назад

Where can I buy a machine just like that?

@realsocrates5272 3 года назад

Where to download the plans ????

@cunhadavid 2 года назад

do you send cnc to Brazil?

@danielorellana2931 2 года назад

Dónde puedo comprar la.maquina cnc

@walterditoro1383 3 года назад

Si possono avere i dxf?

@no_one404 2 года назад

How thick is the MDF board and where did you get it

@ToolsToday 2 года назад

3/4" thick any big box store should have it.

@no_one404 2 года назад

@@ToolsToday thank you

@no_one404 2 года назад

@@ToolsToday but what do you do for starting the gcode so it's in the same spot every time I'm new to this and I'm just trying to figure it out

@fredfowler4364 2 года назад

You defeat the purpose of flattening the board to the machine axis if you remove and fiddle with it. If you want precision, flatten it and leave it be. You probably screwed up the corner stop as well. There is reason you do these ON the machine.