How To Pour A 30' X 30' Concrete Slab with Wire Mesh and Rebar

Подписаться 292 тыс.

Просмотров 38 тыс.

50% 1

#EverythingAboutConcrete #MikeDayConcrete #Garageslab
This video will show you how to pour a concrete slab for a garage.
This slab is 30' x 30' x 6" with wire mesh reinforcement and a double row of rebar around the edges.
We screed off the top of the forms and use a laser level to make a wet pad in the middle of the slab for screeding.
This garage slab has about two feet of gravel under it for a base. The frost line here in Maine is 48" but with good gravel and sloping the landscaping away from the slab, it won't heave.
To learn how to form, pour and finish a concrete slab, see my training course below.
LEARN FROM ME - PRIVATE MEMBERSHIP AREA:
www.theconcreteunderground.co...
GARAGE FLOOR EPOXY FLAKE COATING COURSE:
www.theconcreteunderground.co...
MY STAMPED CONCRETE COURSE:
mike-day.mykajabi.com/offers/...
MY CONCRETE SLAB COURSE:
mike-day.mykajabi.com/pl/79570
FOUNDATION CRACK REPAIR COURSE:
mike-day.mykajabi.com/offers/...
GARAGE EPOXY FLOOR COATING COURSE:
mike-day.mykajabi.com/offers/...
VISIT MY WEBSITE:
www.everything-about-concrete...
USE THE SAME TOOLS I DO:
36" MBW POWER TROWEL:
imp.i284638.net/oeRMmn
ScreeDemon Gas Powered Vibratory Screed:
imp.i284638.net/4ZKEL
Screedemon Battery Powered Vibratory Screed:
imp.i284638.net/LzdBo
14' Screed Board for ScreeDemon:
imp.i284638.net/QOPDZM
MARSHALLTOWN SHOCKWAVE VIBRA-SCREED:
amzn.to/2tZ79ti
TOPCON LASER LEVEL:
amzn.to/2VrJ3zV
DEWALT PENCIL VIBRATOR TOOL:
amzn.to/2Km5Zis
INVERTER GENERATOR LIKE WE USE:
amzn.to/2XfWfwe
BULLFLOAT:
amzn.to/2U1Kx2F
HAND FINISHING KNEE BOARDS:
amzn.to/2TZmTUj
MAG FLOAT & STEEL TROWEL SET:
amzn.to/2IgmDOq
2" MARGIN TROWEL:
amzn.to/2G33KNn
CONCRETE PLACER OR KUMALONG:
amzn.to/2I00gxp
CONCRETE FINISHING BROOM:
amzn.to/2UytU2B
CONCRETE SCREED:
amzn.to/2WZxtwm
CONCRETE EDGER:
amzn.to/2GbGkEp
CONCRETE GROOVER:
amzn.to/2PaL414
BOSCH HAMMER DRILL:
amzn.to/31AHnaN
MY RECOMMENDED TOOLS PAGE:
www.everything-about-concrete...
SUBSCRIBE to my email list and get my FREE video guide on how to get the perfect broom finish on a concrete patio:
forms.aweber.com/form/44/2003...
Follow me on Twitter:
/ creteexpert
Follow me on Instagram:
everything_...
Follow my Facebook Page:
/ everythingaboutconcrete

Хобби

Опубликовано:

22 май 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 69

@cobycorum322 2 года назад

Great video !!! The helmet camera is awesome !!! This helps me to show my new guys what I'm looking for as a finisher. Thank you 👍

@concrete4477 2 года назад

I like these POV videos a lot. Thanks Mike

@tiffanybolen4473 Год назад

You Sir are one of the best In my opinion. There’s no other way to pour concrete, your concrete is flowable and exactly what I would want. Nice work love your video’s.

@3cl1 2 года назад

You guys do some great work!

@FiscalWoofer 6 месяцев назад

those rackers are the key to getting a good clear tamp - and they are working nice and fast! great video

@GoogleIT-qp7mk 3 месяца назад

Awesome job on the quick tamp down and butter with the magnesium trowel.

@alforliniteaching5670 2 года назад

Good video. Informative.

@alwaysapplypressure2477 2 года назад

Excellent Work

@viankalobosvalenzuela7456 2 года назад

Excelente trabajo 👊 👏 👍

@rickpacheco8864 2 года назад

I have a 30x30 garage I built maybe 30 years ago. I went with a 4 foot knee high foundation then poured the slab a few weeks later. Love it, great size garage. The only thing I would do different would be to frame the front for three garage doors, I put two been kicking myself in the ass ever since.

@siilkyjohnson5779 2 года назад

Another day another dollar. You gotta love these perfect size pours with easy truck access

@MikeDayConcrete 2 года назад

I like easy!

@siilkyjohnson5779 2 года назад

@@MikeDayConcrete yes sir, we all do brother

@fljetgator1833 2 года назад

At 1:40 🤣 a 'plumber' sneaks onto the jobsite 🤯 ... . Great pour once again! 🇺🇸

@MikeDayConcrete 2 года назад

Thanks 👍

@iowamatt2519 2 года назад

I have a 34 deep by 26 wide garage I just put up at home. The city wouldn't let me go over 900 sq ft. That extra 4 feet is so much better.

@mikeknoll2865 2 года назад

Beautiful.

@MikeDayConcrete 2 года назад

Thank you!

@emerzish 2 года назад

Perfect size, my last garage was 27 x 27 with 12' ceiling and full walk up attic. That extra 3' would have come in handy many times, so yes perfect size

@MikeDayConcrete 2 года назад

Thanks Ed!

@MetalBum 8 месяцев назад

@@MikeDayConcrete Isn’t that wire mesh too low? It should be in the middle of the concrete slab. But you have it all the way at bottom where ground is

@johnfahey7215 2 года назад

Pullin wire and pouring concrete! Yee Haw!!!😀👍

@MikeDayConcrete 2 года назад

No wire police on this one.

@scoutdoorsurvival 6 месяцев назад

I noticed at you are not pulling the wire mesh up into the concrete. Is it on just to let it lay directly on the wire mech ?

@shannonclark7814 2 года назад

U ever get dunk ponds on your concrete ?

@bman6502 Год назад

Is the builder going to lay the wall on the pad? without a stem wall? Does the pad slope?

@akdrywallguy60 2 года назад

Just bought a piece of property last fall that had a driveway, septic and a 30x30 foundation. Worst size ever. Too big to be 'tiny' and too small to be functional. 2 more feet would have been nice, but we'll make it work out for someone. Great work as always - Cheers!

@MikeDayConcrete 2 года назад

Thanks for sharing

@armedandready9181 3 месяца назад

Thanks for the Vid! the width at 13 secs doesn't look like 30 ft. wide. Of course, only guessing. It just "looks" narrow. Looking at that 2 x 4 at the front edge. Even if it was a 12 ft., that would put it at 24 or 25 feet across.

@jonwestdal69 10 месяцев назад

Right up front please forgive my lack of proper terminology. I'm north of you up in Smyrna Mills. I'm planning to build a 24X28 garage using a mono pour, or perhaps just a slab on grade. In this video it looks like a mono pour. Do you have any videos on how the ground was prepared or perhaps covered in your course? With the frost line being what it is here in Maine pouring a footer and stem wall down to around six feet is a tad expensive. Can that be avoided and just pour on grade with say a two foot by two foot trench around the perimeter filled with gravel and a drainage system? As a side note when I was 18 years old, a long time ago, I showed up for my first day on the job pouring the foundation for a large apartment complex in cutoff jeans and no shirt. You only do that once.

@Rebel635csi 2 года назад

I had a parking pad poured by a local crew on Friday. If I wasn’t in there, moving mud behind the screeder and had my own bull float and poles, the thing would have turned out to be a mess. You sir, make it look easy through your efficiency and skill. He brought unskilled guys who were doing nothing to make it easy on themselves. Watching the screeder killing himself trying to move 6” of mud cuz the guys behind him didn’t know what to do was hard.

@MikeDayConcrete 2 года назад

That sounds scary. Good thing you helped!

@Rebel635csi 2 года назад

@@MikeDayConcrete thanks to you and your videos I knew what “right” was meant to be. Appreciate your videos!

@Anthonyalwayswins 3 месяца назад

Heyy! How much cement did you end up using?

@roynocella2168 2 месяца назад

Hi could you tell me approximately how much a pad that size and that grade how much that would cost me

@Bret5Cr15 Год назад

I was quoted $9K for a 30x30 4" slab for a backyard basketball court. Seemed kinda high? Any thoughts? I know price my vary in different parts of the country.

@jmack48 2 года назад

Hello Mike do you guys take forms off the same day?

@MikeDayConcrete 2 года назад

Yes we do.

@Pablo_19_26 2 года назад

I'm currently working on this size of pad for a client. He's putting 2 10' doors on the back wall, 1 12' door on the left side, and 1 12' door on the front side. He's also wants to make half of the "garage" into a house... a bed, bath, kitchen and living room... I have no idea how he plans on doing that but hey, it's what the client wants 🤨🤷🏾‍♂️

@MikeDayConcrete 2 года назад

Give them what they want!

@Clemsontiger21487 2 года назад

I think you gotta give them what they want mostly; however, I’d let them know your concern. I’d be a mad customer if I realized at the end something isn’t going to work knowing the contractor probably knew, not that it’s your concern. Seems like a silly plan. But that’s a tight rope to walk haha. Good luck

@johnmorris8595 Год назад

Howdy , I'm from Australia and we chair our mesh or ( at worst lift our mesh ) . Just got to ask , are you allowed to pour with mesh on the ground ?? 🤔🤔🤔

@johnwhite2576 9 месяцев назад

There is no law against it, but you are correct. You NEED chairs or dobies to ensure wire remains r proper height inside concrete and mesh is covered by adequate concrete thsi is essential on a 4-5 inch pour where you have little margin for error.

@Raggy73 2 года назад

In the UK inspectors visit construction sites where concrete is being delivered They take a sample of the mix, do a test to see if it is up to standard. Do you have anything like that in the USA?

@cboutdoorfun9955 2 года назад

I have never heard of this being done for residential at least in my area. DOT projects and some comercial and industrial jobs will do this or get core samples after the fact

@andrewwilliams2014 2 года назад

Up in alberta canada we only have them show up for commercial jobs or if it's requested by the owner/builder.

@MikeDayConcrete 2 года назад

Not usually on residential, mostly commercial jobs.

@johnwhite2576 6 месяцев назад

This is why EU residences are built much better; REGULATION and high specs structurally and thermal barriers. Of course the price per square foot would not be acceptable to American consumer, but as the us residential builder quality declines, prices rise and tendency to cut corners expands, we may reach a tipping point. If you are gonna pay seven figures to build a house people are gonna expect houses to be built right.this will happen with teh next recession when the industry is no,longer so flush and complacent.

@MarthaHernandez-pv1qk Год назад

How much cement for that

@stevehopper6068 2 месяца назад

You see the guy pulling up the rebar but then everyone walks over the rebar which pushes it right back against the ground. You need to use dobies to keep the rebar off the ground, inside the cement.

@ChatNoir443 2 года назад

What cures stronger...wet mix or drier mix?

@MikeDayConcrete 2 года назад

Usually a dry mix

@GenerateLance 2 года назад

I’m in the UK and had a cowboy pour my slab a couple of weeks back. My expectation was what this looks like. The reality is a massive disappointment. To the point I wish I could afford to rip it up and start again. I’m 100% confident I could do a better job myself. Great job as always. 👍🏽

@MikeDayConcrete 2 года назад

Thank you!

@garysavala665 2 года назад

A lot of guys promise too much they’re more salesman than finisher . It happens all the time where I live landscape guys trying to do concrete and don’t know how .

@GenerateLance 2 года назад

@@garysavala665 this guy was recommended and apparently does them all the time. Lessons learned 🤬

@MetalBum 8 месяцев назад

Isn’t that wire mesh too low? It should be in the middle of the concrete slab. But you have it all the way at bottom where ground is

@scoutdoorsurvival 6 месяцев назад

I agree with you. They may know something we don't.

@terrypetersen4361 14 дней назад

Mesh should be 1/4 to 1/3 of depth frim bottom

@lonestardiyboyz6610 2 года назад

Why sometimes the concrete is very soupy and other times it is firm?

@el3men2alvarado. 7 месяцев назад

More bigger job the best way are soupy

@briankenison7995 5 месяцев назад

No vaper barrier no insulation No one lifting the mess . You're all fired

@joeconner2669 2 года назад

Y’all having a hard time finding help in your state?

@shsshs3895 6 месяцев назад

What is the point of pulling the mesh wires up when the next person is step it down afterwards. I think it is a terrible work. The mesh wires are at the bottom of the concrete slab and not in the middle of the slab.

@johnwhite2576 9 месяцев назад

There is no way that mesh stays at proper height without support. Chairs, dobies etc.