How to Rebuild an HIF44 Carb - Part 2 Assembly

Подписаться 30 тыс.

Просмотров 25 тыс.

50% 1

#classicmini #carburettor #rebuild #restore #diy
In this episode we will be asssembling the HIF44 carb we took apart in the last episode!
❱ Patreon - / classicminidiy
❱ Shop - merch.classicminidiy.com
❱ Seven Mini Parts - bit.ly/7evenmini
❱ Instagram - / classicminidiy59
❱ Facebook - / classicminidiy
❱❱ Address for Mail Time:
6241 South Blvd
#241403
Charlotte, NC 28217-4157
❱ Parts in this Episode:
HIF44 Carb - cmdiy.co/HIF44Carb
HIF44 Service Kit - cmdiy.co/ServiceKitHIF44
HIF44 Master Service Kit - cmdiy.co/MasterRepairKitHIF44
Sonic Cleaner - geni.us/UB9GdIU (Amazon)
Turbo Sonic Cleaning Solution - geni.us/GNcZH (Amazon) Thanks for watching Classic Mini DIY! Please note Classic Mini DIY assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Classic Mini DIY recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Classic Mini DIY, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Classic Mini DIY. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.

Авто/Мото

Опубликовано:

29 мар 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 31

@minimonte1 5 лет назад

The small brass screws with the slot in the butterfly valve do not open themselves. You need to pry them open once the screw is inserted. This stops them coming out and being eaten by your engine.

@classicminidiy 5 лет назад

Thank you for sharing this. I pinned your comment so people would see it first if they are working on their HIF44

@petersteers8077 4 года назад

Pity he did not set the float height as that is very important.

@RobinTheMini 3 года назад

The overflow is not that I'm afraid. It is the highest pipe at the other side.

@andytaylor9032 2 года назад

The throttle spindle seals are fitted different way round if normally aspirated

@eliaschristodoulou2293 5 лет назад

Excellent video. Very helpful

@terrymerchant4444 Год назад

to fit the throttle spring use a female /female wire crimp,slide it over the spring end,rotate it past where it needs to be,put the quadrant on holding it down and release it gently into place,fit the other piece on and the nut n washer,took me about 30 seconds....

@willsonwang8307 5 лет назад

That's what i need!! thanks!!

@classicminidiy 5 лет назад

👍🏼 happy to help!

@user-qk3yk1pf1t 11 месяцев назад

Hi Cole.i have a 1275 Wolseley with a HIF44 carb.,all my linkages sit on the other side of the carb.Does that matter?and what are the other 2 pipes for?

@rodneymorgan8855 4 года назад

Quick question, there is a "rubber ring" on the one part of the choke assembly, does that get replaced or not

@paulwalters8726 4 года назад

DID NOT SHOW REPLACING THE FUEL JET NEEDLE. CAN BE TRICKY WHEN THE NEEDLE SIDE RETAINING SCREW IS REMOVERED AND THE NEEDLE DOES NOT RELEASE.

@kw8005 3 года назад

Oh no, rebuilt the hif 44 on my difficult to work on ERA turbo, didn’t pry open the screws🤦🏻‍♂️

@jonstout9236 5 лет назад

Hi Cole - good video. Small comment - the screw at 9:15 for fast idle adjustment under choke should be installed the other way around so you can access the head of it... good luck with the installation! :)

@TimWilkinsonPoland 3 года назад

You can access the head from the side, it is installed the correct way round.

@jonstout9236 3 года назад

@@TimWilkinsonPoland Wow! That was a blast from the past!

@TimWilkinsonPoland 3 года назад

@@jonstout9236 ha yea sorry, watched these videos a year ago when I was rebuilding my hif44, just getting started today 😅

@jonstout9236 3 года назад

@@TimWilkinsonPoland Cool - I have re-conned a few - did you get the proper SU kit?

@TimWilkinsonPoland 3 года назад

@@jonstout9236 yea got the proper rebuild kit from the sucarb website.

@redmartian 2 года назад

around 11:30 be sure to have your hand on the mute button. The difference between the burst of music and the mic level is quite a bit.

@terrymerchant4444 Год назад

yeah,made me jump

@danielcopp6773 5 лет назад

Really great job, very detailed!! I've got a HS4 on my mini - any chance of doing a rebuild on one of those?

@classicminidiy 5 лет назад

Thanks! I do have plans to do an HS4 in the future. However in the meantime, I have done detailed videos on the HS2 during my bad wolf build and the HS2 is almost identical to the HS4. 👍🏼

@danielcopp6773 5 лет назад

@@classicminidiy Great, I'll have a look, thanks!!

@ryancamilleri9473 3 года назад

can you tell us how to set it up mine needs a good set up

@classicminidiy 3 года назад

I have another video about tuning the HIF44 carb already: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-GnR4cxDou7s.html

@ryancamilleri9473 3 года назад

@@classicminidiy fantastic thank you for all the help you give us keep it up stay safe

@DSouter1 4 года назад

What about the O-Ring under Dashpot?

@classicminidiy 4 года назад

There is no o-ring under the dashpot on the HIF44. The only o-ring lives at the bottom float chamber. www.minisport.com/selector-carb-hif38-hif44

@DSouter1 4 года назад

@@classicminidiy - I Have a Landrover Defender with 2 x HIF44 Carbs and they definitely have an O ring under dash pots.

@DSouter1 4 года назад

@@classicminidiy - I am not sure if we are talking about the same part - I am talking about the O-Ring which goes under te Suction Chamber - Part 11 on exploded view in workshop manual.