No video :(

How to Remove CV Axle On a RZR Stuck CV Axle

Подписаться 9 тыс.

Просмотров 36 тыс.

50% 1

If you're having trouble removing your RZR CV axle hard to remove, watch this video and we'll show you how to do it easily. This video is applicable to cv axles.
If you're looking for a way to fix your RZR CV axle, then watch this video and we'll show you how to do it quickly and easily! We'll walk you through the steps, and by the end of the video, you'll have your axle back in place and ready to go!
Harbor Fright Puller
www.harborfrei...
How to Remove CV Axle On a RZR Stuck CV Axle
#RZRCVAxle
#RZRproCVAxlereplacement

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 13

@jbello100 19 дней назад

Agree Rhinos are no better than stock. Been through two sets front and rear and will never buy again. Great video! Thanks!

@TH3G00DT1M3S 4 месяца назад

Thank you for making this i was ready to set this side by side on fire till this video your the man 👍🔥🔥🔥

@6gatornation 4 месяца назад

I made a tool that looks just like the axle magic 2 using a slide hammer except on the end I welded a exhaust clamp that you will tighten down to the axle cup it helps if the clamp catches the backside of the cup Make it long so you don't have to take the axle apart if it's really stubborn You can attach a ratchet strap to the end of your slide hammer to create tension I use my golf cart to pull from

@billyalexander2783 Месяц назад

i had one that i couldnt get out no matter what i tried, so i ended up welding two approx 4 foot peices of rebar on the inside of the remaining part at 3:00 and 9:00 and at the end of those rebar i welded a flat plate between the two rebar. that gave me a flat surface that i could hit with a sledge and what ya know it came out with the first pursuasive hit.

@tpaul340 Месяц назад

Ratchet strap will fit behind it, hook it wear the tire was attached, and ratchet til it pops off.

@hemtet5500 10 месяцев назад

I have seen someone weld some bar across the remaining shaft the get the slide hammer with a hook attached then whipped it out very quick.

@FusionOffroad 10 месяцев назад

We have done that before; it works just have to be careful it does not hit you when it flings out.

@Natbet-re8uo Год назад

Jerk the cv shaft with a chain and hammer If you do break the cv joint then get a bolt to fit inside the chain. Weld the bolt across the cv cup then jerk out with chain and hammer

@FusionOffroad Год назад

We have done that but we welded the chain to vise grips and feed the chain through hammer! Just did not make a video if someone get hurt from doing it lol

@anthonypiraino6742 8 месяцев назад

I made an adapter out of 4” pipe tap 3/8 holes welded 1 1/2” strap to both sides an attached the same puller to it after you hit out a few times hit it in and then out it will come

@mattsims3778 Год назад

Hey man I seen y’all at wildcat today in KY. Looking forward to maybe seeing a video from there.

@FusionOffroad Год назад

We are out and doing videos for a copy days then we will post them! Day #1 down and Day #2 is about to start! Maybe we will see you out there today

@A-mechanics-review-4U Месяц назад

You at very least have to be pulling the axle perfectly straight out of the hole sir, not on an angle even a tiny bit. i see alot of rust on the unit so soak the axle with PB at the diff. for 1 day 1st..