How to Remove Front Bumper 97-05 Lexus GS300

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,5 млн

Просмотров 18 тыс.

50% 1

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/59/G/...
In the video, 1A Auto shows how to remove and replace a scratched, dented, broken or loose front bumper cover. The video is applicable to the 97, 98, 99, 00, 01, 02, 03, 04, 05, Lexus GS300
🔧 List of tools used:
• 10mm Socket 1aau.to/oVj/1AX...
• Plastic Fastener Remover 1aau.to/oaE/1AX...
• Ratchet 1aau.to/oair/1A...
• Socket Extensions 1aau.to/o4c/1AX...
For More Info visit us at 1aau.to/h/bBn/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

16 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@1AAuto 4 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@tomchillen3039 3 года назад

DO NOT FOLLOW THEIR DIRECTIONS. As others have stated, there are two bolts on each side that they neglected to mention. They hold the bumper in on the seam directly above the turn signal. They are difficult to get to and require a 10mm deep socket. Had they taken the time to Google a diagram they would have found the same info, but instead they advised to just yank until it comes off. Following that advice I broke my bumper off below the headlight. Due to their laziness I now have to spend hundreds on a new bumper. As others have said, please pull this video.

@MrFoxfire510 2 года назад

How crucial would you say is it to put those 2 bolts back on each side of the bumper… they are a pain. Would be a lot easier to not put them back on and off in the future..

@astonmarjo Год назад

You are correct sir! I have three of these cars and there are a few bolts that need to be taken out from the back side from each side.

@RemyHDP 3 года назад

You forgot the 2 ten milimeter a the jonction of the bumper and the front fender, you juste broke the bumper by the way

@adamrychlick 3 года назад

Thanks for the help. I did see the other two on the front of each fender, no biggie if you have a foot extension and a universal with a deep socket 10mm on it. Both mine sheared off on each side but I have no intention of reinstalling so I’m good. Thanks again

@Golo1949 5 лет назад

You were struggling because there are two bolts either side where you are pulling which hold the bumper to the wing, very difficult to reach, that's why one side came off easy because the last person couldn't be bothered to refit them.

@1AAuto 5 лет назад

Thanks for watching our video! +Golo1949

@timp5668 5 лет назад

He's right. After my bumper wouldn't come off, I scrolled down to the comments to see what was wrong. You should pull this video.

@vlat18 4 года назад

so how many bolts are there, i counted 6?

@MrFoxfire510 2 года назад

How crucial would you say is it to put those 2 bolts back on each side of the bumper… they are a pain. Would be a lot easier to not put them back on and off in the future..

@astonmarjo Год назад

There are two more 10mm nuts if I'm correct that connects the bumper to the fender as everyone has stated already. please don't pull it will come out with ease once every nut is free. 👍

@ericlroark48 3 года назад

You forgot the last impossible bolt on driver side under headlight to release bumper. Other than that good video 👍

@1AAuto 3 года назад

+Eric Roark Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@darielvazquez3422 4 года назад

Previous owner went to take off the bumper cover and snapped the very same clip you had problems taking off, now i’m stuck here trying to jb weld it on the inside 😂 It’s being replaced soon so i’m not really worried, but it gets annoying having to see it like that everyday

@trilliamogdlocog4986 2 года назад

Missed like 5 more bolts but it's alright alot of times parts that been taken off before and not put back are hard to catch either that or you just ripped the rest off lol

@jnakz9066 2 года назад

He skipped steps.

@sal8361 3 года назад

Would it be similar on RX300

@morganmclennan5593 Месяц назад

Babbles on trying to sound like a pro as he tears the bumper off 4 remaining studs below the headlights completely wrecking it

@oSIXO. Год назад

Rear bumper?

@elir.torres8642 Год назад

There is a bolt on that left corner.

@Kay_Money-no2sp 3 года назад

U said put somewhere so it don’t get scratched up u put it on the ground and yanked the other side 😂 but thanks for the help

@pressedoff 4 месяца назад

Yall are so annoying for this, yall should delete this video because I guarantee tons of people have followed this and fucked up their bumpers because of you , should have read the comments