How to Remove Your Cars Front Bumper 

That's too much! Anyways, glad to hear that this video helped you out. Thank you very much! Take care.

I want this bumper, how can i get this in saudi arabia..

@@photographyandphotoediting1944order through a dealership

Thank you very much sir!!

Glad it helps! Thanks a lot man!

Thank you very much sir!

Thanks man! Yeah, it is very complex to look at.

Glad to hear. Thank you very much!

Thank you very much!

Thank you very much!

Thank you very much! Yes, that could be the culprit or the hose that connects to the motor might have cracks or damage. If the front end of the car has minimal collision, check for cracks on the washer tank reservoir. That can also be a possible cause.

Hello Indo , what was the leaking of ur washer Tank , because i have the same poroblem ???

Hello Indo , what was the leaking of ur washer Tank , because i have the same poroblem ???

@@gohraa88 I still havent fixed lol

Agree. Thanks!

Greetings! Thank you and take care!

Sorry for the late response bro. Based upon inspection, there are screws at the back of the bumper. I'm not sure if that will separate the chrome part but, you can try to remove the screws. Probably there are clips there and hopefully it would separate from the bumper. Sorry for that bro, I could not assure you since its been a long time since I removed the bumper and I did not inspect the details at the back of the bumper.

@@DraftProject thanks for the info man! I am going to try that. Keep doing your videos, they are amazing!

@@ren7907 You're welcome and thank you very much bro for supporting my channel! Good luck bro! :>

The chrome part can be removed. In my car, the chrome part was broken and I replaced it with a new one.

@@tarikdemir thanks for your answer!

Makakagawa rin po kami niyan sir soon! Maraming salamat po.

Muchas gracias también. Sí, es necesario quitar el parachoques si necesita cambiar la bocina. In English translation: Thank you very much too. Yeah, removing the bumper is needed if you need to change your horn.

Hi sir! Currently I don't have one. Most of the time we do it in our own ways. Applied guesswork hehe. It's hard to find a workshop manual since the car is still relatively new. Unlike older cars, you can find it everywhere in the internet. About the wires on the fog light housing, it is a reserved wire for the fog lights. Just like in other vehicles, you can find some harness connected without an actual unit. The fog lights for this car is optional and you can use those wires whenever you install a fog lights. Basically, you have to add more stuffs like relays and switches. Just trace the connection of the wires to make sure that you can connect it to your added stuffs and accessories. Also, manufacturers produces pretty much the same wire harness for all models, except for the higher trim models which have extra harness for added accessories.

Sorry for the late response. Unfortunately, I haven't got the chance to inspect the underneath of those upper black plastic covers to determine if it is possible to remove it. Even so, I would still recommend to remove the whole bumper so that you can gain more access and space. I believed that the upper plastic part are held by some plastic clips but it is not worth trying since these are delicate and hard to remove too. Thank you very much!!

@@DraftProject thank you very much for the reply! i agree.

Perhaps this is what you have been looking for: Fastener Part Number: B45A-56-146A Hope this helps. Thank you!

Hi sir, sorry for the late response. Actually you need to remove the bumper first because the bumper is attached to the headlight itself via plastic clip. You will see a gray square plastic piece which is locked into the headlight assembly. Also, I couldn't remember that much but I saw that the lower part of the headlight assembly is attached to the chassis. As far as I remember, it is bolted. Perhaps you can try to remove half of the fender liner and remove some parts there. Maybe that could help you gain some space for you to remove that LED bulb.

Yes, as demonstrated in the video.

I have a video for that. Please check the link that I have provided below. Mazda 2 Rear Bumper Removal: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-1qkDWQhGIE0.html Thank you!

Thanks alot just did mine and i didn't have to break every existing clip 😂 , keep on the good work sir .

@@kenyrios4841 Thank you! Yup, will do!

Try checking at your local automotive scrapyard or perhaps on online marketplace to get this type of bumper.

@@DraftProject do you have the link of online marketplace..

@@photographyandphotoediting1944 I tried looking but it turns out to be difficult since the vehicle is still new. You can try searching on Ebay, Amazon and others. Here is an example from an automotive shop site. www.japotoparts.com/en/part/Mazda/2-/Front+bumper/15842743 Sadly, there is no stock anymore. You can try searching similar to that link. Hope it helps. Thanks.

@@DraftProject okey thank you so much 💗

That's how a modern car works nowadays haha.

Yeah hehe it would have been a lot better with thin gloves. It just happens that those gloves were the only ones I had from that time, so I didn't have that much of a choice and still, it's better than nothing.

Sorry for that. Yeah that would be better. Thank you!