Тёмный

How To Replace A Pilot Bearing 

klowny1969
Подписаться 93 тыс.
Просмотров 75 тыс.
50% 1

In this video i show how to replace a pilot bearing on a manual car. I use the free loaner tool from advance auto. You can also use bread to push it out. Dont forget to subscribe!!!
********Get your klowny1969 Shirts and Apparel here:
teespring.com/stores/klowny1969
How to replace a clutch in your car:
www.youtube.com/watch?v=boMs0...
Check out my other videos:
How to change a tire pressure sensor (TPMS) yourself:
www.youtube.com/watch?v=PDpDm...
Dakota digital dash Install (1982-1992 Camaro)
• Dakota Digital Dash In...
How to install a 4L60E transmission:
• How To Convert a Stick...
How to Wire A Switched fuse block:
• How To Wire A SWITCHED...
********Get your klowny1969 Shirts and Apparel here:
teespring.com/stores/klowny1969
SUBSCRIBE TO MY CHANNEL! Also check out the videos below!
Complete Brake Overhaul:
www.youtube.com/watch?v=TVA0t...
Vintage air serpentine setup:
www.youtube.com/watch?v=ByVdD...
How to Upgrade your fuel pump:
www.youtube.com/watch?v=8-7sB...
How to install an electric vacuum pump:
www.youtube.com/watch?v=i1n3b...
How to build a camaro from top to bottom:
www.youtube.com/watch?v=5twT_...
400 Cubic inch small block Dyno testing:
www.youtube.com/watch?v=eavm4...
How to Clock an Alternator:
www.youtube.com/watch?v=_I24m...
How to Replace a u-joint:
www.youtube.com/watch?v=QQsXs...
How To install a trans pan drain bolt:
www.youtube.com/watch?v=zXFCB...
How to install subframe connectors:
www.youtube.com/watch?v=9n1Yc...
How to do a quick wheel alignment (toe in toe out):
www.youtube.com/watch?v=Ycdoo...
klowny1969 - best car mechanic on youtube
Only clown mechanic in the world !
This video can be applied to chevy, ford, mustang , impala , camaro , corvette, truck , toyota, lexus , honda , nissan. etc.. volvo cadillac gmc astrovan truck blazer silverado turbocoupe thunderbird

Авто/Мото

Опубликовано:

 

14 ноя 2019

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 49   
@Stoked_wharf2000
@Stoked_wharf2000 7 месяцев назад
My transmissions teacher played this in class without watching the whole video so safe to say we had a fun time at certain parts of the video.
@klowny1969
@klowny1969 7 месяцев назад
Lol
@ShadowRockers
@ShadowRockers 2 года назад
I have a similar puller, which did not come with instructions. Instead of mangling the old bearing and possibly damaging the outer surface, I watched your video first. 5 minutes later old bearing is out. Thanks for posting. 👍💯
@klowny1969
@klowny1969 2 года назад
Awesome..don't forget to subscribe
@Giorobot
@Giorobot 3 года назад
Otta boy great video goes 2 the point I didn't know which way pilot bearing faces but you nailed it thanks
@klowny1969
@klowny1969 3 года назад
Thank you for watching and commenting..don't forget to subscribe
@125sm3
@125sm3 4 года назад
Great demonstration Klowny,
@klowny1969
@klowny1969 4 года назад
Hey..thanks for stopping by again!
@caspianfox6596
@caspianfox6596 2 года назад
instaBlaster
@thebigpicture2032
@thebigpicture2032 4 года назад
I like it! Don’t have to use part of my sandwich any more.
@klowny1969
@klowny1969 4 года назад
LOL everyone loves the bread trick
@DOUBLE0SEVUN
@DOUBLE0SEVUN Год назад
Thanks for your video!
@klowny1969
@klowny1969 Год назад
Thanks for watching and don't forget to subscribe
@Dubiels
@Dubiels 4 года назад
I always look forward to the intro burnouts in your videos. Keep it up man!
@klowny1969
@klowny1969 4 года назад
Lol thank you
@BellaRocko
@BellaRocko Год назад
Awesome! Thank you so much, it was exactly what I was looking for! But poor Brianna... LOL😂
@klowny1969
@klowny1969 Год назад
Thanks for watching..and yes Bryanna his been through alot!!
@bilbobaggins4710
@bilbobaggins4710 4 года назад
For parts which are press fit I like to put them in the freezer for an hour....Seems to help them slide in more easily 👍😁
@klowny1969
@klowny1969 4 года назад
Yes that works too! thanks for commenting and watching!
@Laxxo96
@Laxxo96 Год назад
Which is of better quality? Powerbuilt 648619 vs otc 4422.
@johnmilner7603
@johnmilner7603 4 года назад
I fill the hole with grease then use my spare input shaft and hammer with a 1/4” of steel on the end of the input shaft. As the bushing comes out I add more grease to take up the empty space. Forgot to mention, I install the bushing using my old input shaft too. I also use my old input shaft to align my clutch disc rather than using the loose fitting plastic one that came in my clutch kit.
@klowny1969
@klowny1969 4 года назад
Yes..works with bread too..thanks for watching and commenting!
@edwardperdue8212
@edwardperdue8212 2 года назад
I have a bolt ,but I use bread now, it's so clean and honestly it was faster,spare input shaft? Just how rich are you
@scrufscruff5883
@scrufscruff5883 3 года назад
So... if bearing is installed backwards (seal facing front of motor instead of facing transmission)..... will it cause any other problems besides extreme difficulty bolting Transmission back up to the motor? Picked up a cheap Ford Ranger. Did a new clutch system on it. Put everything in exactly the way the old stuff came out. Turns out, release bearing was in backwards... so I installed new one in backwards (not knowing) as well. Took FOREVER getting Trans to bolt back up to the motor!!! But once back together, everything seems fine. Should it be ok? It's not like the shaft moves in and out, or one end of bearing is wider or anything.
@bubbavox
@bubbavox 3 года назад
I dunno, I figure the pilot bearing's seal is there to keep dust out of the bearing. I assume you're talking about the pilot bearing. The release bearing is part of the slave cylinder -- the pilot bearing is where the tranny input shaft meets the crankshaft, at center of flywheel.
@jwwilliams
@jwwilliams 3 года назад
Pulled the old one out on mine and it was a bit beat up. Having hard time putting the new one end. It doesn't want to go in at all. Hammer on it a bit and it falls out. Wondering if I have the right one to replace it. Looks exactly the same as the old one and fits on the input shaft fine. Figuring on getting a small wire wheel and going to town in it to clean it up. Any ideas other then putting it in the freezer?
@Supanova70
@Supanova70 2 года назад
freeze the new one to shrink it over night
@jwwilliams
@jwwilliams 2 года назад
@@Supanova70 Good idea. Thanks. I actually ended up paying someone else to finish the job after several failed attempts but if i ever try again i will take your advice into consideration.
@fls360
@fls360 4 года назад
Welcome to Klowny's Porn Garage. Today Brianna gets a crash course of the ins and outs of proper lubing with insertions! As always great how to vids Sir Klowny. BTW folks help a producer out and grab some Klowny gear.
@klowny1969
@klowny1969 4 года назад
LOL yes!!! Klownz porn garage has a good ring to it!!
@juiced71
@juiced71 4 года назад
💯💯💯!
@juiced71
@juiced71 4 года назад
Hey bro I can’t find that vacuum pump video you did .. the one where you used a sabb pump I believe?
@klowny1969
@klowny1969 4 года назад
ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-i1n3bX1OirI.html
@klowny1969
@klowny1969 4 года назад
They changed what it comes with though
@juiced71
@juiced71 4 года назад
klowny1969 thanks brother man! I appreciate it ..
@klowny1969
@klowny1969 4 года назад
You got it
@hughhughes4488
@hughhughes4488 4 года назад
Hey, my dad wants to know where your shop is? Somewhere on Long Island?
@klowny1969
@klowny1969 4 года назад
Sorry I'm not taking customers at this time..thanks for watching
@honda123456g
@honda123456g 4 года назад
What pilot bearing puller did you use ?
@klowny1969
@klowny1969 4 года назад
I thought I showed it in the video
@space_monkey3410
@space_monkey3410 4 года назад
slice of bread... preferably white
@klowny1969
@klowny1969 4 года назад
That works too
@superduty4556
@superduty4556 4 года назад
That's a weird looking piece of bread, my man.
@klowny1969
@klowny1969 4 года назад
LOL..everyone loves the bread trick..I dare to be different
@chemicalspore
@chemicalspore 4 года назад
No butter sauce required.
@klowny1969
@klowny1969 4 года назад
Damn..I totally forgot about the butta sauce!!
@chemicalspore
@chemicalspore 4 года назад
@@klowny1969 it happens
@kennedywong9854
@kennedywong9854 Год назад
What tranny mate with engine?
Далее
How to Remove and Install a Pilot Bearing
8:07
Просмотров 49 тыс.
Tipuan Jenius dalam Mengasuh Anak & Gadget Cerdas
00:21
Video #10 Pilot Bearing operation
2:53
Просмотров 3,7 тыс.
What Is A Spun Rod Bearing - Explained
4:40
Просмотров 53 тыс.
Pilot Bearing Removal Using BREAD - Jeep Wrangler
4:55
How to fix a grinding gm ac compressor
3:34
Просмотров 442 тыс.
LS Rear Main Seal Warning! Don't Do This!
4:50
Просмотров 243 тыс.
Stuck Pilot Bearing Removal
3:48
Просмотров 3,5 тыс.
How To Remove A Pilot Bearing
4:14
Просмотров 56 тыс.
Ждать пока остынут ступицы?
0:34
🔈 Звуки поломок авто. Часть 4!
0:54
Легкий тюнинг 🤣☝️ #goodcarkz
0:26