How to Replace Engine Mount 2007-2012 Nissan Versa

Подписаться 540 тыс.

Просмотров 20 тыс.

50% 1

Buy Now!
New Engine Mount from 1AAuto.com 1aau.to/ia/1AEM...
This video shows you how to install a new engine mount on your 2007-2012 Nissan Versa. A shaking or vibrating engine, or bucking when changing gears are signs of worn engine mounts.
This process should be similar on the following vehicles:
2007 Nissan Versa
2008 Nissan Versa
2009 Nissan Versa
2010 Nissan Versa
2011 Nissan Versa
2012 Nissan Versa
Tools you will need:
• 10mm Socket 1aau.to/obed/1A...
• 16mm Socket 1aau.to/obyv/1A...
• 18mm Socket 1aau.to/oajn/1A...
• 19mm Socket 1aau.to/oajn/1A...
• 1/2 Inch Ratchet 1aau.to/oajn/1A...
• 1/4 Inch Ratchet 1aau.to/obed/1A...
• 3/8 Inch Drive Ratchet 1aau.to/obyv/1A...
• Torque Wrench 1aau.to/oaHP/1A...
• Gloves 1aau.to/oac3/1A...
• Safety Glasses 1aau.to/o6a/1AX...
• Floor Jack 1aau.to/o7M/1AX...
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

14 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 6

@TRQ Год назад

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@chrisdotson6417 Месяц назад

I came to your video after performing this procedure. Engine cover can stay on the engine. Those 2 bolts are left alone. Then I removed the mount for the cold side AC line. and the Electrical ground next to it. This allows the AC line to flex with that rubber portion of the line. I then only need to remove the 3 mount bolts at 48 ft lbs. and then the Center bolt at 77 ft lbs. And the other torque vibration isolator bolts are both 103 ft lbs. You do not need to remove the bracket holding the mounts. I would rather not mess with the cast aluminum bracket bolts to hold that to the engine. Just another method and only needed to touch the bolts holding the mounts. Plus 1 ground, and 1 bracket bolt for the AC line. Your way works as well. Lastly double check that torque. FSM I read said 103 ft lbs on the torque vibration isolator above that Engine mount. Also torque order for the Engine mount is the single bolt in the rear, then the bolt on the wheel side, followed by the bolt on the engine side of the front of the mount.