How to replace front and rear A arms on an Arrma 4x4

Подписаться 979

Просмотров 8 тыс.

50% 1

Getting some fresh parts installed is always satisfying whether its a repair, upgrade or both at the same time.
RPM part numbers:
Front: RPM81492
Rear: RPM81502
Hot racing makes aluminum A arms for these vehicles as well, along with several other upgrades. Here is a link to that site if you would like to check it out: hot-racing.com/?c=1345_Arrma_...
I am not sponsored, though they do make some great parts for these trucks and many others as well.
If you enjoyed, please consider liking, commenting and subscribing. Your support is much appreciated!

Авто/Мото

Опубликовано:

20 май 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 13

@nrd515 3 месяца назад

I have bad hands and found that getting a 7MM wrench with a larger diameter handle makes putting the wheels on/off much much easier. I found a cheap one on Amazon and bought a pair of them. One at home, one in the car toolbox. Brand is Auvotuis. I was using a wrench like you did in the video and it was difficult to remove the nut. Too many cars worked on, too many fights as a bouncer, and old age make your hands hurt!

@TommasoVario 5 месяцев назад

Thank you your video helped me fix my arm.

@keithsanchez3257 5 месяцев назад

This was very helpful, thank you.

@stoneywardog 2 года назад

My granite doesn't have screws in the front bulkhead just pins for the arms

@simplixit 2 года назад

I have watched 3 of your vids not realizing and I loved all of them thx

@AyItsBigDrew 2 года назад

Amazing video! Very happy watched it once, now I'm a pro at it. Thank you very much my friend keep up the great work.

@drawstraw4483 7 месяцев назад

Is it the same arm as on the granite? And have you heard of people using a little longer arms? I just broke a front a arm , very front where the pin slides in, and I'm looking at these aluminum one's now but want just a bit more width on it to add stabilization. Already done shocks. Any time your not busy if you happen to know. I know that this is a senton. I'm really pretty new to this. Got tools though and the means to upgrade. Just want to go in the right direction, strength and stability. Thanks

@joeman205 6 месяцев назад

I’d also like to know if this is the same as the granite and if there are other ones to use. I broke mine in the same spot

@drawstraw4483 6 месяцев назад

@@joeman205 well I found out you can use the Typhon arms which will surely widen the granite, and as for the aluminum arms... I have them, but did decide NOT to put them on. I just replaced the A-arm with original OEM arm. The reason for not using aluminum's is the next time I have a collision it will send the impact to something much more costly to replace, chassis.

@francislevisantos6167 3 года назад

Thanks for another great video! Have you tried 3s or 4s yet? Because I’ve been having problems with my slipper clutch burning out near the spring where the bearing is attached.

@fullandtenth6405 3 года назад

Yes! I've been having quite a bit of fun with a 3s, planning on trying a 4s in the future. while the brushed slipper clutch can take 3s brushless I would recommend the brushless clutch as it lasts quite a bit longer and grabs better.

@synergyiii 2 года назад

your vids are good man, you just need a better quality camera

@pnworegon2668 2 года назад

be careful all with these cars. i bashed in the wet and the bearing on the motor seized up, also water got into the motor its self. i just did a castle SW4 upgrade on mine.