How to Replace Front Door Lock Cylinder 01-07 Toyota Highlander

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,5 млн

Просмотров 20 тыс.

50% 1

1A Auto shows you how to repair, install, fix, change or replace a broken, damaged, worn or faulty door lock key cylinder. This video is applicable to the 01, 02, 03, 04, 05, 06, 07 Toyota Highlander.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/ozV/1AX...
• Phillips Head Screwdriver 1aau.to/ozV/1AX...
• 10mm Socket 1aau.to/orN/1AX...
• Trim Tool Set 1aau.to/oeL/1AX...
• T30 Driver 1aau.to/ofY/1AX...
• Ratchet 1aau.to/ozY/1AX...
• Socket Extensions 1aau.to/ouT/1AX...
• Pick 1aau.to/ocr/1AX...
• Razor Blade / Gasket Scraper 1aau.to/o6/1AXA...
For More Info visit us at 1aau.to/h/3g/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

6 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 14

@1AAuto 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@mnsweeps 5 лет назад

Great video..No matter what I do the Torx screw is not locking into the lock cyclinder assembly. You see to do it easily at 7:06 . I had to remove the door handles also to replace a front door actuator and I followed your video for that which was very helpful. Even I had an issue removing the yellow prong and had to remove the door handles and assembly inside My problem is getting the lock cyclinder assembly back in its place. The hole on lock cylinder doesn't seem to match the screw :-(

@affordabledesertliving3487 Год назад

Really well explained. Major question from me: Is this similar for a 1998 Corolla? Thanks.

@uzmam2612 4 года назад

Thank you for the video. I have a 2015 Toyota Corolla and I’m replacing the drivers door. I was wonder if you have any knowledge about the key fob? Is reprogramming all I need to unlock my door?

@xlmaster9298 2 года назад

Thanks for this video! I have a 2003 RAV4 (which is not a whole lot different from the vehicle in your video), and I am having a very hard time trying to secure the passenger side lock cylinder in place, after having removed it to fix the door lock actuator. I had trouble doing this for the driver side door as well, about two weeks back (spent many, many hours on just this one task). Today again I spent numerous back-breaking hours trying (unsuccessfully) to bolt the lock cylinder in place. For some reason, I cannot seem to get the securing bolt for the cylinder to line up easily and correctly with the screw hole, so that I could tighten the lock cylinder in place, as you demonstrated in your video at 7:06. Do you have any tips, tricks, or helpful hints to share, to allow me to succeed in this task? It's causing me to tear my hair out in despair and frustration. I seem to be missing the screw hole by a few millimetres, since I can see the marks the bolt is leaving on the body of the cylinder, a little to the left of the screw hole. It almost seems as though the round hole in the door chassis is either not large enough, or not at the correct angle in order to line up the bolt with the screw hole in the cylinder. Thanks.

@dbmn7571 5 месяцев назад

seriously! You didn't show swapping the old lock assembly into with the new lock assembly.

@uzmam2612 4 года назад

Another question I wanted to ask, do I need to unplug my battery when uninstalling my old door and installing a new one?

@danielkarl49 3 года назад

Would this be similar to a 2009 toyota sienna?

@1AAuto 3 года назад

+Daniel Karl We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@ririzarry2000 6 лет назад

Where in your website is the plastic prying tool?

@1AAuto 6 лет назад

+Rafael Irizarry That tool set can be purchased here! www.1aauto.com/interior-trim-removal-kit/i/1axxx00004

@simonseth1000 6 лет назад

Hi mike u guys r great. Have a question about a hyundai tucson 2011 what battery goes in it cant find anything online the hyundai dealership wont return my calls! i will buy it from u have great parts

@1AAuto 6 лет назад

+takethat witchu We currently do not sell batteries,but if you have a different question we can try to help you out. 1aauto.com

@simonseth1000 6 лет назад

I really appreciate u getting back 2 me wish nothing but the best