No video :(

How To Replace Lower Ball Joint 1998-2011 Ford Ranger

Подписаться 502 тыс.

Просмотров 98 тыс.

50% 1

Buy Now!
New Ball Joint from 1AAuto.com 1aau.to/ib/1ASB...
Modern suspensions combine a number of moving parts for safe and stable handling. The ball joint is the crucial moving component that ties those parts together. The ball-in-socket joint can wear out and loosen over time. Or, the rubber protective boot can tear, allowing contaminants to seize the joint. Bad ball joints are a common failure point on vehicle inspections because they lead to unsafe driving conditions. Fortunately, they are relatively easy to replace with the right know-how. This video shows you how to install new, quality TRQ ball joints on your 1998-2011 Ford Ranger.
• Check here for more videos on the 1998-2011 Ford Ranger: • Ford Ranger 1998-2011 ...
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
Tools you will need:
• Pry Bar 1aau.to/ohi/1AX...
• Ball Joint Press
• Brake Caliper Hanger 1aau.to/oaV/1AX...
• Trim Tool Set 1aau.to/oiS/1AX...
• Channel-Lock Pliers 1aau.to/obB/1AX...
• Snap Ring Pliers
• Straight Cutters
• 3/8 Inch Air Impact Gun
• Ratchet 1aau.to/oCD/1AX...
• Socket Driver
• Torque Wrench 1aau.to/oqY/1AX...
• Rust Penetrant
• Center Punch 1aau.to/obB/1AX...
• Floor Jack 1aau.to/oiH/1AX...
• Hammer 1aau.to/ohx/1AX...
• Jack Stands 1aau.to/ohU/1AX...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford Ranger 1998-2011 3rd Generation: • Ford Ranger 1998-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 31

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@STBRetired1 2 года назад

Don't you just hate professionals? Look it only took a 12 MINUTE video to change out the lower ball joints. For us backyard guys that equates to about 12 HOURS. And then there is another 12 HOURS on the other side. But blessings to you for showing us step by step how to do the job.

@Rtb323 Год назад

I always end up with one side beeing easy to the other side beeing a b to work with lol .. I’ve ran into that so many times

@Dude13450 2 года назад

Any body else just love how the rotor and caliber magically became brand new after torquing the axle nut?

@THEL0G1CAL1 2 года назад

Just a little bit of refurb wire brush and paint. LOL

@Shep01 Год назад

laughed out loud when i saw that. Magic!

@timschosek4871 Год назад

I was able to replace the lower ball joint on my 2wd Ranger without removing the spindle. It saved a lot of time and the tool fit right in without a problem.

@M0N0T0N0US 2 года назад

Love it when how to videos just get to the how to and leave out all the bs!!!

@REALWOODSMAN 10 месяцев назад

This would have taken me 2 days

@mts7274 Месяц назад

Is it possible to leave the axle in the hub assembly when lowering that steering knuckle off the ball joint shaft? It looks like there would be enough play.

@yoyokum1483 2 года назад

Air compressor tools is probably a good idea.

@edmundreiss5144 2 года назад

Don't you have to take the torsion bar out to relieve pressure? I have a 2001 Ranger 4wd with torsion bar and 4.0 engine.

@dylanlucas388 Год назад

You should specify that this a 4wf model, as there are differences.

@toddbob55 2 года назад

If thats an Aftermarket Autozone, Oreilly, Napa Ball joint it should last around 10,000 miles before it fails.......OEM/FORD original dealership ball joint will last 250,000 miles.

@cmercer555 Год назад

very well done video. Great job.

@douglasdailey5998 3 года назад

One thing they didn't say on this video is that it is a wheel drive.

@scottcoffman2046 3 года назад

It’s 4x4

@brentbriscoe1581 8 месяцев назад

He also used a knurled ball joint which you should only use if the hole is loose.

@kyleimgarten2696 Год назад

Yeah! Bonk!

@adolfoalvarez639 10 месяцев назад

How much do they charge to replace the ball joints?

@yvanauchterloni5923 6 месяцев назад

drinking game: Take one shot for every "loving bonk" he gives the vehicle.

@crassvegan6511 Месяц назад

How do you watch your eyes

@bubbap8595 4 месяца назад

This is torsion suspension. Correct? I'm getting mixed up

@bubbap8595 4 месяца назад

Is this only for 2 wheel drive.

@ghosttimer Год назад

Is it possible to do this without the airgun?

@jmusicnu_1240 2 года назад

Im having a very hard time removing the lower ball joint from the hub assembly on both sides. I have tried a pickle fork and many different hammers and im still not able to get it loosened. Any suggestions like other kinds of tools I could use or something? Its says in my Haynes book not to use heat because it will weaken the metal.