How to Replace Rear Window Regulator 01-07 Volvo V70

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,5 млн

Просмотров 26 тыс.

50% 1

Buy Now!
New Window Regulator from 1AAuto.com 1aau.to/ia/1AWR...
1A Auto shows you how to repair, install, fix, change or replace a slow, stuck, cracked or damaged window regulator. Video is applicable to the 01, 02, 03, 04, 05, 06, 07 Volvo V70
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oJ5/1AX...
• 10mm Socket 1aau.to/oyU/1AX...
• Rivet Gun & Rivets
• Trim Tool Set 1aau.to/ohc/1AX...
• T25 Driver 1aau.to/oiD/1AX...
• Ratchet 1aau.to/oKK/1AX...
• Socket Extensions 1aau.to/oDo/1AX...
• Drill
• Drill Bit Set 1aau.to/om/1AXA...
• Painter's Tape
• Chisel 1aau.to/oaT/1AX...
• Hammer 1aau.to/ofB/1AX...
• Razor Blade / Gasket Scraper 1aau.to/oaD/1AX...
For More Info visit us at 1aau.to/h/akS/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

16 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 13

@1AAuto 4 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@nwsights6301 Год назад

Would it be possible to just re install the regulator with bolts and nuts instead of the rivets?

@charlesstevenson5894 3 года назад

Really useful - my Passenger rear window's just stopped working and I need to remove the trim to diagnose it further. Thanks for your how to suggestions.

@gregwestbrook7029 4 года назад

Thank you, thank you, thank you! I just did this for the cost of a used regulator and pop rivet gun ($45) and it works perfectly!

@1AAuto 4 года назад

+Greg Westbrook Thanks for checking us out! 1AAuto.com

@marcojaen5626 3 года назад

Thank you for the detailed explanation; something new I learned today. My experience ordering from A1 Auto was easy and within 2 days shipping delivery. Supper fast :)

@Khrrck 11 месяцев назад

If anyone ends up here who needs to replace the window glass like I did instead of the regulator, here's the procedure: 1. Drill out rivets holding glass to regulator. Then retract regulator and glass to lowest position. 2. Remove rubber trim from around window and guides. You will have to pull it UP out of the guides. Rear side guide is a plastic piece held in by a Torx screw into the edge of yhe door and one plastic pin into the window frame. Carefully remove both and pull the guide upwards out of the door. This will take some finagling. 3. You can now pull the window up. The side of the glass towards the rear of the car has a notch giving you enough clearance to tilt the window a little towards that direction. Maybe 15 degrees or so. This will give you enough clearance to slide the window up, out of the tracks and out of the window on the "in" side of the door. 4. Do all these things in reverse order to install the new glass. Be sure the new glass is inside the window tracks and the rubber trim is firmly seated around the window and in the tracks.

@ianrice2600 4 года назад

What size rivets are needed for this?

@warehamtown 3 года назад

Yooo you ever find out what size??

@stevebutler812 4 года назад

I just spent ten minutes searching 1A auto's website for the exact part shown and linked here, except the passenger side. I even cut and pasted the wording from here, from the link, etc., and tried changing "drivers" to "passengers" and there was only a "sorry, not found" message. WTH? Off to the salvage yard.

@1AAuto 4 года назад

+Steve Butler Thanks for checking us out. It appears we no longer carry the item you are looking for. We apologize for any inconveniences.

@AB-hx9hs 3 года назад

This has to be the dumbest design. Why put rivets instead of regular screws/bolts...is there a reason as to make the job more complicated and requiring specialized tools ?

@cheesememe4986 2 года назад

To raise the cost of repair and charge more. And it prevents people like you and I from doing it easily in our garage without buying extra tools. BUT you can actually remove the MOTOR itself. There are 4 T25(I think) screws and it comes right off. It's possible with a narrow screwdriver to fit inside the door. Much easier to do it with the window up but chances are if you're in this situation it's probably fully down. I wish she would have mentioned it for people like me in a pinch that JUST need the window to go up for now and worry about it later. Take the motor out, pull the window up, reinsert burnt motor, good to go.