How To Replace The Front Wheel Bearing And Hub On A 2004-2011 Ford Focus

Подписаться 218 тыс.

Просмотров 99 тыс.

50% 1

Brian Eslick from How to Automotive www.howtoautomo... takes you step-by-step through the process of replacing the front wheel bearing and hub on a 2004-2011 Ford Focus.
Affiliate link mentioned in the video for GMB 725-0242 Wheel Bearing Hub Assembly amzn.to/2YnlOYv
Affiliate link mentioned in the video for MILWAUKEE ELEC TOOL 2861-22 Mid-Torque Impact Wrench amzn.to/2LI1Bec
Affiliate link mentioned in the video for Milwaukee 2552-22 M12 FUEL Stubby Cordless 1/4" Drive Impact Gun Wrench Kit amzn.to/2Jkg3GW
Affiliate link mentioned in the video for OTC 6575 Hub Grappler Kit for on Vehicle Wheel Hub and Bearing Removal amzn.to/2LIiGob
New! How to Automotive T-shirts, stickers, and more! teespring.com/...
Affiliate link mentioned in the video for How to Automotive Tool Store www.amazon.com...
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomo...
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: / how-to- Automotive-432536836946801/?ref=settings
Google+: plus.google.co....
LinkedIn: / brian-esl. . 819839118
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #HowtoAutomotive

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 88

@HowtoAutomotive 5 лет назад

Be sure to check out the How to Automotive Tool Store www.amazon.com/shop/howtoautomotive

@Neur0bit 5 лет назад

Fantastic explanation. The quality of your videos is superb. No fluff and to the point. Thanks Brian for sharing!

@HowtoAutomotive 5 лет назад

Neur0bit glad you like the video. Thank you for watching!

@jimmcmahon217 Год назад

Excellent tech info and production values. Just what the shade tree mechanic needs to know, presented at a no-fluff, no BS pace. Watching your video is a real time-saver to anybody doing this job for the first time.

@ozzstars_cars 5 лет назад

Really great tutorial Brian, should be helpful to anyone doing this job.

@HowtoAutomotive 5 лет назад

Thank you Glen!

@quietstormofspokenword9946 2 года назад

You are an Excellent Teacher! Your directions are precise and the fact that you are not overly wordy is so Appreciated!

@TheFifty3five Год назад

This video was insightful and straightforward! I want to personal thank you for posting this. I chose to do it step by step. Some of my bolt configurations were different and different sizes as described in the video. However, this video was perfect for sequence and torque specs. Really appreciate it, great work.

@nickblum5091 2 года назад

Thank you keep doing this please I am a mobile machanic and I don't know everything but it's really nice to watch and be able to have my tools ready and know what to expect ahead of time saves so much time

@pfsantos007 4 года назад

The orientation of the bearing does matter. There is a side that has to go near the speed sensor. I believe the black side, but you should confirm. But good video overall. Nice to see a torque wrench being used.

@christophervalencia5919 Год назад

thank you- the job is complete and i found a ball joint that was busted (side note - getting those rivets out were difficult) thanks again

@jasonwalker8028 Год назад

Decent video explanation with one exception... It absolutely matters on which way the new bearing is placed into the steering Knuckle. I just found out the hard way that the brown side needs to face the ABS speed sensor on the inside because there's a magnet on that side for the sensor. If it's not, then there will be an error code, the ABS light will be forever lit on the instrument cluster, and there will be no ABS function when braking. This will be a redo for me at the added cost of two new bearings again. This is another life lesson that just because someone posts a video to try and make money, they don't always know what they're doing.

@anthonyg.valletta8895 4 года назад

Outstanding video. You made it look easy with that bearing press kit.

@HowtoAutomotive 4 года назад

Anthony G. Valletta thank you!

@pizzamonster975 3 года назад

This is one excellent video. Video quality is superb. Instruction is perfect. Thank you so much.

@aaronbeepdoo9728 3 года назад

That torx bolt on the bottom of the knuckle was a huge mistake on Ford’s part, so easy to round bits with age if you don’t have air tools.

@derekreilly1039 2 года назад

It does matter wich way u put the bearing in because the abs ring on the bearing needs to face the inside for the abs sensor

@LettuceNeck 3 года назад

Very helpful video. Only detail missing is removing the ABS sensor! Broke mine doing this bearing and hub job

@lilnis9 2 года назад

I don’t think that car has one

@759fish 6 месяцев назад

the easy way I found to do this job is to remove the steering knuckle after removing the hub with the slide hammer , easy access to the snap ring and getting out the bearings , so for all you that do this in your garage with jack stands .. save your back and do it on the bench !, also after pressing in the bearing to avoid damage to the dust cover on the bearing press in the hub first then install the snap ring.

@jareddavis6329 8 месяцев назад

I appreciate the info. Great video and to the point.

@derekreilly1039 2 года назад

You put the bearing in backwards the brown ring is for the abs sensor

@dcarino0405 4 года назад

When pressing/pulling in the hub, you want to support the inner race, not the outer race.

@jgeorges3061 5 лет назад

Brian, Awesome video/info thanks for sharing brotha, cheeeeeers

@haccoon5458 9 месяцев назад

The brown seal is a magnet for the speed sensor. Without it your ABS light and traction control light will come on. It goes on the back side facing the CV joint. Ask me how I know….

@serg1184 10 месяцев назад

Great video, very clear and straight to the point! Only question I have is, why torque the center nut with the wheel on vs it off? Is there a difference or is it just personal preference?

@erinburke9711 8 месяцев назад

That's an easy way to prevent the hub from rotating

@zbreezy190 10 месяцев назад

Just a tip to anybody who may be having trouble getting the hub off…. Get the axle out of the hub first before trying to yank the hub off. Makes it so you’re only fighting against one contact point vs. two

@zach_waltonn 3 года назад

Do I need to use grease as a lub when putting the new one in or does it have to be dry

@Rockhound1943 2 года назад

So I just did this job. Had some trouble but seemed like reasonable hiccups. When all was said and done I put the car down and here's the bad news I got no movement. I have some cranky noises. Could I have pulled the trans axle out out of the transmission? Is it possible it's not seated properly. I'm at a bit of a loss. Thoughts?

@joeprogar669 Год назад

Excellent video.

@HowtoAutomotive Год назад

Thank you!

@alexandervillalobo2970 11 месяцев назад

Wow… THANK YOU

@HowtoAutomotive 11 месяцев назад

Thank you for watching!

@9Tange 2 месяца назад

How do you know you need the Bearing replaced?

@AmitSharma-fp5xd 2 месяца назад

What size socket I need to remove the tire bolts. Thanks

@scottgilkey5894 3 года назад

I'm about to check daughters car to see if I need to but I've seen 2 videos and both are taking out bearing but when I changed them in my old ford 07 windstar they sold me the whole knuckle with bearing? They don't for the focus?

@no-worries-its-okay Год назад

Great Video. !!

@soundsbyel1421 2 года назад

I have this square piece holding the bearing in like the snap ring, in the same area as the snap ring. How do I remove it?

@islandbeaches395 Год назад

Easy way is removing the steering knuckle off the lower control arm and used a 12 ton strongway press from northern tools

@darthgreater7054 Год назад

Red thread locket takes heat to remove. Shouldn't you be using blue instead? I heard you shouldn't heat suspension components, especially if they have rubber bushings like where you put red thread locker on the tie rod connection bolt.

@snewcomer6831 3 года назад

2010 Focus SE with the manual 5-spd, just changed the Hubs and CV axles because I had a bad vibration up front, bought CV’s but it ended up being the front left hub so I just did them all, runs, drives, and feels like normal. Though soon as I pulled out of the garage the ABS, traction control, and brake light, all came on, dash said check brake system, and throws the two codes, C1233 and C1234 - left/right front wheel speed sensor input signal missing, i definitely bolted them back into the knuckle, any input is appreciated. Thanks in advance.

@zGenjin 2 года назад

Did you put the bearings in backwards

@snewcomer6831 2 года назад

@@zGenjin solved this awhile ago, but yes, yes I did lol

@krissyk1036 2 года назад

How would I know if I also need the knuckle replaced

@MitchelTJones 4 года назад

I don't see a link for the slide hammer and hub adapter. Also the grappler kit you linked does appear to have a hub puller included (one that uses the impact vs a slide hammer) would that work in place of the slide hammer?

@michaelwayne7887 3 года назад

Thanks for the towel tip. Great video.

@JohnDoe-zr6bk Год назад

How come your hub has only four studs? My 2008 focus has 5.

@etchosts8162 4 года назад

Beautiful

@jalilconley-anderson3584 4 года назад

would a makita 18V Cordless Impact Driver work in replacement of the milwauke m12 impact driver

@Eleven-dk4be Год назад

Hub grappler ... noted

@LeoAlvarez. 2 года назад

Broke ABS sensor and instructions weren’t very clear ended up breaking bearing after I put the new one on with the snap ring…

@micharris1761 2 года назад

ty a great video.

@HowtoAutomotive 2 года назад

Thank you for watching!

@micharris1761 2 года назад

@@HowtoAutomotive you are welcome, I was wondering if you could maybe answer a question for me, on the speed sensor cables they are molded so is there a tool for helping split that molded cable so it can be spliced the tiny wires are inside. some of the speed sensors for the abs do not have plug and go. ty .

@scoyle1750 3 года назад

Good upload subbed👍

@HowtoAutomotive 3 года назад

Thank you for watching and subscribing!

@volcanofood8373 4 года назад

Its not that easy! The fit between the axle and hub is so tight it will require a press slide hammer and lot's of heat The towel to grab the slide puller is a hand saver Great Idea! Dont give up!

@eddiekatura4465 4 года назад

Thats why you put the axle nut on till its flush with the axle and hit it with a hammer or use an air hammer

@aaronditchfield781 Год назад

The sill is not a weight bearing point for jacking or lifting

@josekings346 4 года назад

Do u need alignment after all?????

@HowtoAutomotive 4 года назад

jose kings There’s nothing really that will affect the alignment in this job but it is a good idea to have it checked.

@imyourhuckleberry8009 4 года назад

Where is the abs speed sensor wire?

@pfsantos007 4 года назад

Must have been removed at some point doing the procedure. Comes in from the top of the Hub goes into near the back of the bearing.

@LettuceNeck 3 года назад

Left this out. Consequently I broke my abs sensor. My fault

@velocity800 5 лет назад

Hi, can that stubby milwaukee undo the wheel nuts on a classic mini cooper?

@HowtoAutomotive 5 лет назад

Yes but it’s not made for it.

@HowtoAutomotive 5 лет назад

Check out the review video on the Stubby. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-FlP8BbkjN9E.html

@dan43213 4 года назад

Easier to buy hub/spindle assembly

@mquinn1138 2 года назад

Can you direct me to a video that shows this? I'm not interested in using a press

@tonyford4170 2 года назад

I totally agree, I bought a complete bearing kit, all in one, and I am expecting it to be a lot easier than this vid, I do not know why the guy is dismantling so much for a simple job, ? Maybe it's a USA Focus ?