How To Replace The Valve Cover Gasket On A BMW 335i

Подписаться 214 тыс.

Просмотров 71 тыс.

50% 1

Brian Eslick from How to Automotive www.howtoautomotive.com/ takes you step-by-step through the process of replacing the valve cover gasket on a 2007-2010 BMW 335i with N54 motor.
Affiliate link mentioned in the video for Victor Reinz Valve Cover Gasket amzn.to/2j5Gb9h
Affiliate link mentioned in the video for 3M 08008 Black Super Weatherstrip Adhesive Tube - 5 oz. amzn.to/2iWkQ4R
Affiliate link mentioned in the video for SK 19761 13 Piece 3/8-Inch Drive E4 to E24 Torx Socket Set amzn.to/2i3YsVV
Affiliate link mentioned in the video for Assenmacher (ASMBMW10160) Extra Deep 10mm Socket amzn.to/2h4xjnB
Affiliate link mentioned in the video for New Milwaukee 2457-21 M12 Cordless 3/8" Ratchet Kit With Battery Charger Case amzn.to/2isgXli
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomotive.com/
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: / how-to-autom. .
Google+: plus.google.com/+HowtoAutomot...
LinkedIn: / brian-esl. .
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick

Авто/Мото

Опубликовано:

7 янв 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 138

@BarryBtheCool 7 лет назад

Like you were there walking me through it. Thanks man, I got it done and saved a thousand bucks!

@HowtoAutomotive 7 лет назад

BarryBtheCool very cool! Glad you saved that money. Thank you for watching and writing!

@NUNYABIZNNAAAZZZ 5 лет назад

I'm doing mine next weekend! Ty for making this video

@FinalVibes 7 лет назад

This isn't my car and I accidentally came across this. I just want to say that this was filmed perfectly.

@HowtoAutomotive 7 лет назад

Otto thank you! What type of car do you drive?

@rcmojon6 6 лет назад

Just finished the valve cover gasket job on my 2008 335xi. Took me about 9 hours and I took my time and did some extra stuff along the way. Your video saved me $1k. If there is someone who should get paid for youtube vids, it is you! The editing, narration, and concise yet clear depiction is remarkable. And YES, its very important to have the reassembly instructions.

@HowtoAutomotive 6 лет назад

Bob Mozo glad the video helped and save you money! Thank you for the nice words and for watching.

@LiLDiesel23 7 лет назад

Ladies and Gentlemen, THIS Is how to make a How To Video!! Thanks brother, really helped me out. perfect editing! keep up the good work!

@HowtoAutomotive 7 лет назад

LiLDiesel23 thank you glad I could help. Thank you for writing!

@zchevyridinhi 7 лет назад

Very well done video. I especially appreciate you taking the time to document reassembly which is usually left out of these videos. Thanks so much. I just subscribed.

@HowtoAutomotive 7 лет назад

zchevyridinhi thank you subscribing. I think that's what sets my channel apart from others is all my videos are start to finish.

@2Hottdoggs 4 года назад

That’s the best video of this VCG repair

@Hope4NewDay1 7 лет назад

My valve cover gasket is good and all so I dont know why I'm watching this video but damn this is a good tutorial. I love how you went over how to put every thing back together instead of saying "follow the directions in reverse"

@HowtoAutomotive 7 лет назад

Hope4NewDay1 glad you like the video. Thank you for watching and writing!

@7213eduardo 6 лет назад

Can't stop watching this video... You make it look so easy!!!! I replaced my starter but I don't think I can do the valve cover. Not that smart Haha

@HowtoAutomotive 6 лет назад

Edwardo zubiate glad the video helped. It Took me 25 years of working on cars to make it look easy. Thank you for watching!

@JeffCapeci 6 лет назад

Excellent How To video. I just finished replacing the valve (head) cover gasket on my 2008 535XI. The detail is great and it really helped taking everything apart as well as while trying to figure out how to put everything back together.

@HowtoAutomotive 6 лет назад

Jeff Capeci glad to help. Thank you for watching! 535xi is an amazing car I love how it handles.

@JeffCapeci 6 лет назад

How to Automotive it is a fun car to drive but at 120k, I will be doing some suspension work to bring its handling back to factory original but that must wait until I change some fluids.

@reyesescobar7253 5 лет назад

Wow I will try doing it with my 07 Bmw 335i myself tomorrow by watching this Thanks, you my friend have the patience for this

@evanguidry4831 6 лет назад

You are an amazing auto tech i love the work. definitely subscribing. Your explanations are spot on, i love the way you teach ! more videos please !

@burhaan9017 5 лет назад

Thank you for making these videos. I have now used this one and one for the coolant tank replacement on my 2008 535xi and the secondary air injection on my 2005 lexus GX470. You show in such a strait forward and easy manner with good technique especially during trouble areas. I think the least people can do is buy the recommended parts off of your links, hopefully that would pay you back in some way.

@mucyoshami8058 5 лет назад

Ohhh man! Fantastic! I am working on this issue on thanksgiving, this video is the best of all that I watched on this issue on RU-vid! If you can, please another video about changing crankshaft position sensor on this N54 engine! Good job, you got me subscribed!

@ggj13557 7 лет назад

Outstanding video! Very clear step by step procedure.

@slinkyking8956 7 лет назад

Fantastic how to diy sir. Keep up the great work

@HowtoAutomotive 7 лет назад

joshua dyball thank you!!

@paulperez509 7 лет назад

thank you this is Paul just responding to your feedback thanks a lot for your help,God bless you.

@HowtoAutomotive 7 лет назад

Paul Perez than you

@bobit8742 7 лет назад

Wow you make everything look so easy

@HowtoAutomotive 7 лет назад

Binh Tran thank you it's just repetition done lots of them.

@glennburch104 7 лет назад

About to do mine myself and this is a great video to help me, thanks a lot!

@HowtoAutomotive 7 лет назад

Glenn Burchfield glad the video will help thank you for writing!

@OSCARCAPETILLO07 6 лет назад

i liked how you explain every step thanks saved me $650

@HowtoAutomotive 6 лет назад

Oscar Capetillo nice 650 is some good saving. Thank you for watching and sharing!!

@rob8535 7 лет назад

Perfect video thanks! Now I know what'll be done to my car for what it'll cost thanks🙏🏼

@diwins70 5 лет назад

Very good class my friend. Thank you so much.

@doughoward6486 7 лет назад

I plan on doing this soon, thank you.

@KozmikEl7 7 лет назад

man great job I've learned plenty from this can you do one on the oil pan gasket replacement? great video

@HowtoAutomotive 7 лет назад

Kozmik El as soon as one comes in I will

@algiebryant5057 6 лет назад

Gr8 video my brother. U r the best.

@HowtoAutomotive 6 лет назад

Algie Bryant thank you and thank you for watching!

@BR1NG1ND4R41N 7 лет назад

Can you please send me link for the insulators and great video by the way!

@ianyoung6829 7 лет назад

Hi Brian do you have any video on doing the valve cover gasket on a 2008 bmw 328, Or is it the same as the 335, Please advise.

@federicotorresbordils7624 4 года назад

Congratulations for the Video. Should I disconnect the Battery to do such a job or at least negative cable? Thanks in advance BimmerN53

@bernardomartinez3853 5 месяцев назад

Thanks for the video

@vravo7775 7 лет назад

Thank you Very much for Sharing.

@HowtoAutomotive 7 лет назад

Jonny Vravo thank you for watching and writing!

@Bad_m340i 6 лет назад

best 335i vcg diy. thank you.

@HowtoAutomotive 6 лет назад

Omair Siddiqui thank you and thank you for watching!

@Bad_m340i 6 лет назад

How to Automotive do i need a torque wrench or a regular one is fine?

@HowtoAutomotive 6 лет назад

Omair Siddiqui if you have a good feel for tightening things you could do it all by hand.

@natereihanian9825 7 лет назад

Can you please leave a link for the tube seals and for the 2 vacuum tube lines you talked about replacing during this video? BMW wants 22$/sleeve which is a joke. Also, is the 10mm socket you used longer than 1/4inch drive? Or is that long enough?? Thank you! Please let me know asap, trying to do this in a few days

@ayusoj 7 лет назад

Great video, thank you!

@HowtoAutomotive 7 лет назад

Juan Ayuso thank you!!

@ArnoldBodyByVI 5 лет назад

Wow wow wow! That is a project- I have anexiety watching this and have no guilt that I payed Midas $713.69 to remove and replace the valve cover gasket from my 2007 328i

@NUNYABIZNNAAAZZZ 5 лет назад

Great DIY, performed it to the letter, but now the car wont turn over. Any ideas?

@HowtoAutomotive 5 лет назад

Chris Smith cranks but won’t start or it’s not cranking?

@HowtoAutomotive 5 лет назад

Chris Smith try pulling codes maybe something did not get plugged back in.

@NUNYABIZNNAAAZZZ 5 лет назад

@@HowtoAutomotive its turning over just fine...

@NUNYABIZNNAAAZZZ 5 лет назад

@@HowtoAutomotive Yea i went thru the video again....the ONLY thing a screwed up was over tightening the middle, deep 10mm bolt in the middle of the valve cover that holds the ground wires from the spark plugs, it broke off, part of the bolt is still there, so I just ran the 3 ground wires to the front post (by crimping to a longer 12g wire)....surely this cannot be the reason isn't not firing up??

@NUNYABIZNNAAAZZZ 5 лет назад

Ok, so the car started. I pulled all 6 of the new coils I installed, I noticed from all DIY videos on spark plug and coil replacement that the coils where slightly angled up, almost at a 45 degree, mine were all straight to the right...so I pulled them all up (took alot of force) and resat them, in the correct place and inserted the wiring, firmly and the car fired right up. Im still pretty upset with myself for breaking that, deep 10mm, middle ground bolt off...I dont know how to extract it, I have the replacement bolt already. Any idea? I have a few pics if you can help further.

@ggarl12 5 лет назад

Do I need to replace the valve cover and gaskets to replace the pcv valve?

@mikejohnson2426 2 года назад

Thanks for your video, things were great until i tried to start it, i only try's to crank but does nothing. Sounds like it binds up when i hit the starter? What did i do wrong? 2009 335i 103k miles please help.

@paulperez509 7 лет назад

okay thank you so much I really appreciate it, I'll give you a thumbs up.

@HowtoAutomotive 7 лет назад

Paul Perez thank you!

@jessevanvoorhis384 7 лет назад

Great vid! This may seem like a dumb question but do you have to drain the oil for this?

@buddyrepairs6902 7 лет назад

Jesse VanVoorhis no you don't jesse

@sweatsome2009 5 лет назад

Question, will this work on a 2011 535 xi?

@pvvallartense3306 5 лет назад

Do you have to drain the oil before you start the process?

@pedrocarvajal3166 7 лет назад

Do you have to do anything to bleed the air out of the fuel system since you remove the fuel rail and the lines that go from the rail to injectors?

@HowtoAutomotive 7 лет назад

Pedro Carvajal you don't need to bleed the system it will bleed when the injectors opened up to spray.

@cuddapah 7 лет назад

Excellent video. Your engine is same as in my 2011 BMW Z4 35i. Following your video, I could get to the point where you removed the 2 vacuum lines and fuel line. Video was cut at the vacuum lines near 9:17. How to remove the 2 vacuum lines ? Is the fuel rail attached to the cover ?

@HowtoAutomotive 7 лет назад

Chakravarthy Cuddapah The fuel line is not attached to the cover but it's bolted right next to it and it pinches it. So if you take the mounting bolts on the fuel rail off it'll will lean back just enough to clear the valve cover.vacuum lines are flexible and you pull him through

@cuddapah 7 лет назад

Thanks for your quick reply. Can you please tell me how to remove the 2 vacuum lines ?

@HowtoAutomotive 7 лет назад

Chakravarthy Cuddapah I held the plastic portion of the lines in one hand and used a screwdriver to push the vacuum lines off the tubes. You can also use a small pick tool to pick inside the hoses to loosen them up.

@lindacurtis9730 6 лет назад

Great video. I got everything off but cannot for the life of me get the cover off. Now Ive cracked it and put a hole in it trying to get it off. It almost seems like there's some type of suction holding down. Help

@HowtoAutomotive 6 лет назад

Linda Curtis it sounds like there is one bolt still holding it down. I have seen the covers get stuck on there though. I recommend that you try prying in several different areas.

@Cdswjp 6 лет назад

How much more difficult and time consuming would it be to change the cylinder head? And what other steps would be needed?

@HowtoAutomotive 6 лет назад

CDMusicGroup that would be another 10 to 12 more labor. That's a huge job

@AfteMath 7 лет назад

you did it in 22 min, it will take me 22 days hahha

@TheTruelakersfan 6 лет назад

It was edited took him way longer

@nickcabral8723 7 лет назад

What else can use to take off bolt that use the snap on 10 mm thin wall? Can't find one anywhere.

@HowtoAutomotive 7 лет назад

Nick Cabral Hi Nick. I just added a link for That socket in the description. It's the 4th affiliate link down. Hope this helps.

@peterkrzesinski5941 6 лет назад

Does it have to be a thin-wall type socket or will a pass through work as well?

@thejamaicansenpai1698 7 лет назад

OMG thank you for making this video. I have a 2010 335i coupe and I'm new to the BMW car world. I was just surprised on the many area's the N54 motor has oil leaks. Mine is where the oil filter is, bad oil filter housing gasket and oil cooler gasket, and the other place is the engine valve cover. Going to the dealer will cost an arm and a leg. I have no issues doing it myself, I'm just glad I found this video. The most accurate and step by step video. With this I can finally start my gasket replacement not to mention spark coils and spark plug project. Quick question, for the spark plug tubes. Are you sure this is the correct part number 11127575422. I looked it up and it said for N52 engines. Then again they could work for the N54. Would you be able to let me know?

@HowtoAutomotive 7 лет назад

Marcris Tyrell I can check on those parts in a couple hours and get back to you.

@thejamaicansenpai1698 7 лет назад

Thank you very much

@Qzeckgamer 7 лет назад

nice video . after done everything my car is thiking and i feel have no power when i hit gas . any idea what is going wrong thanks

@HowtoAutomotive 7 лет назад

Diego Soto sounds like it's miss firing. I would pull codes and go from there.

@LuisRodriguez-pg6nf 7 лет назад

perhaps the ticking gets louder when you take off the top engine plastic cover with the foam on it. i had a problem though where one of those vaccuum lines that run behing the oil cooler housing acrros the top of the valve covers ruptured on me therefore i didnt have a proper vaccuum to the turbos causing them to not spool. please check that since he did state they will easily break off. This was a week ago so hopefully you found what was wrong!

@Qzeckgamer 7 лет назад

Luis Rodriguez thaks for the information yes the cover take the ticking noise away . .but i will chekc the vaccun lines . again thanks

@d.c.robinson1717 7 лет назад

if i had to get to the head gasket, does that mean i have to replace the valve gasket as well?

@HowtoAutomotive 7 лет назад

D.C. Robinson if your car needs a head gasket when you order the kit it should come with a new valve cover gasket also

@MagicalxNY 7 лет назад

Did you drained all the oil ? or was it okay with full engine oil?

@HowtoAutomotive 7 лет назад

Frank Vasquez you don't need to change the oil unless it's due.

@luisurrutia8100 7 лет назад

Hello, what are the likely symptoms of this gasket wearing out, besides oil leaking.

@HowtoAutomotive 7 лет назад

Luis Urrutia the only symptom is oil leak. The gasket only last about 3 to 4 years before they start to leak.

@luisurrutia8100 7 лет назад

How to Automotive not any misfire do to pool of oil on the coils and sparks?

@HowtoAutomotive 7 лет назад

Luis Urrutia yes that is a possibility.

@Lyfe_on_My_Terms 6 лет назад

Hey sir, question, how long should a job like this take? The mechanics I go to said it's a half day job and would be around 600 for labor. Is that true or am I being conned?

@HowtoAutomotive 6 лет назад

K B The labor is about 5 1/2 hours and most shops charge around 100 bucks an hour so I would say yes this is in the ballpark.

@Lyfe_on_My_Terms 6 лет назад

How to Automotive ok thanks man :)

@HowtoAutomotive 6 лет назад

K B glad to help. Thank you for watching!

@paulperez509 7 лет назад

which valve cover gasket should I buy BMW or aftermarket for my 535ix Drive 2009

@HowtoAutomotive 7 лет назад

Paul Perez on this particular one either or will work just fine. And I think the prices are pretty comparable to.

@lemuelalfaro9848 7 лет назад

i have de problem bmw 535i xdrive the code is p2096 i chage de pcv,manifold gasket,the charge pipe .please need help

@HowtoAutomotive 7 лет назад

Lemuel Alfaro code P2096 is for the oxygen sensor before the Cat. If the code was there before you did the work on the car then most likely the oxygen sensor is bad or a large vacuum leak somewhere. If the code appeared after you did the work on your vehicle I would go back over your work and double check for any vacuum leaks or any wires left disconnected.

@lemuelalfaro9848 7 лет назад

To the car they changed the injectors the gasoline pump since it appeared that code I take it to the mechanic because it had a gasoline smell and it was the oring of the gas pump it was mounted a new oring but the code keeps appearing. And nothing changes the pcv valve selenoide control and nothing returns the code change the charge pipe complete with blowoff and nothing returned the code the last thing I did change the joints of the manifold when I turned on the car the code p2096 off but the next day I do not know what else to do. What I noticed is that when I use the car during the day to do the errands the code seva. In the scaner that stays blinkied is the evap. I hope you understand everything I wrote thanks for wanting to help me

@ydtech2649 7 лет назад

hello have you replaced the wastegate rattling issue? thank you.

@HowtoAutomotive 7 лет назад

Yohan Ds I have not run across it yet. But if one comes in I'm definitely going to film it.

@ydtech2649 7 лет назад

Where are you located?

@HowtoAutomotive 7 лет назад

Yohan Ds I am in Encinitas California

@ydtech2649 7 лет назад

Damn shame bro you seem to be very good mechanic. I'm in Miami.

@HowtoAutomotive 7 лет назад

Yohan Ds thanks. I'm sure there are some good guys in Miami.

@rcmojon6 6 лет назад

How about the oil pan gasket for this car?

@HowtoAutomotive 6 лет назад

Bob Mozo no video on the pan yet but when one comes in the shop I will film it.

@RecreationAutomotiveGarage 7 лет назад

are this engine common leak on valve covers?

@HowtoAutomotive 7 лет назад

satawat senyotkham I would say yes it's a very common leak on BMW's

@wigglebee3631 7 лет назад

Nice! I like that you're to the point and don't begin with "Whazuuup, RU-vid!". QUESTION: Should the valve cover bolts be replaced during this job? What are your thoughts and reasoning?

@HowtoAutomotive 7 лет назад

Wiggle Bee you definitely do not need to replace the bolts on this job. The bolts are not torque to yield bolts and the cover is made out of plastic so the torque is not very high. Thank you for watching and writing!

@wigglebee3631 7 лет назад

Thank you for the response. That does makes sense.

@shaanhajju3368 7 лет назад

thanks

@HowtoAutomotive 7 лет назад

shah haj glad to help. Thank you for watching!

@Majortom721 6 лет назад

dam. fantastic!

@HowtoAutomotive 6 лет назад

Jackson A. Kemper thank you!

@davidOrtiz-ms5pf 7 лет назад

Car started shaking after I put everything back can anyone tell me where i could of have gone wrong

@HowtoAutomotive 7 лет назад

david Ortiz most likely a misfire. Go back over all the coils and unplug them and plug them back in. Also pull codes if you can you.

@davidOrtiz-ms5pf 7 лет назад

Okay thank you so muchI will be doing that tomorrow

@adriansandoval9719 6 лет назад

Wow , I wish I could do this with only one hand .

@HowtoAutomotive 6 лет назад

Adrian Sandoval lol. Thank you for watching!

@thejamaicansenpai1698 7 лет назад

By any chance do you have the part number or item number to the Deep 10mm socket. I've finally stated this project but hit a wall with that part. I went to auto zone, advanced auto parts and they did not have one deep enough. I'm going to snap on tools but I'm not sure what the part number is. Any help will be awesome

@HowtoAutomotive 7 лет назад

Hello Marcris. her is a link for that socket. thank you for watching amzn.to/2sKx6aJ

@thejamaicansenpai1698 7 лет назад

Oh thanks so much. Now I can get my car up and running. Thanks again for your help and the best video I've seen

@Idksomething883 4 года назад

Can anyone provide a time estimate on this repair labor wise? I went to the dealership today and of coarse they tried to rape me with 6k in repairs. This was one of the repairs they said I absolutely needed. I’ve done this on several other non-foreign cars and the job wasn’t that bad. After looking at this, seems like a pain but there are many RU-vid videos on this repair for my vehicle that range anywhere from 30 mins to 1 hr 15 minutes. They quoted me 4K for the repair and it’s $75 in parts. So that $3925 in labor, which doesn’t make sense to me considering I would assume a certified BMW technician with a moderate level of experience would be capable of performing this repair within 4 hrs ish. I’m going to just do this job myself but how long has this taken others to do and how badly are the dealers ripping ppl off?