Тёмный
No video :(

How to reverse single phase motor direction 

ELECTRECA
Подписаться 47 тыс.
Просмотров 103 тыс.
50% 1

Single Phase Motor Direction Change
To reverse rotation on a single phase capacitor start motor, you will need to reverse the polarity of the starter winding. This will cause the magnetic field to change directions, and the motor will follow. In order to achieve this, you can swap the connections on either end of the winding. Always reverse the wires that lead to the starter winding.
Note that most motors, if still labelled with manufacturer instructions, will indicate that they are non-reversible. If this is the case, it's likely because the wires you would need to access are housed within the motor. If your unit has this warning, it's easiest not to proceed. If, however, your motor is reversible, you might notice that it provides instructions for reversal. Usually, these instructions will tell you which wires to change. For instance, some units might have you switch the red and green leads in the terminal box at the end of the casing. In other instances, the blue and yellow wires may need to be swapped. The colour of the wires is highly individual and depends upon the brand and model of motor you have. It's best to read the instructions provided by the manufacturer before proceeding.
watch more videos here
Direct online part 1 • direct online starter ...
Direct online part 2 • direct online starter ...
Selfholding circuit • contactor self holding...
Selector switch • Float Switch Selector ...
Star delta starter • star delta starter con...
Float switch • How to use float switc...
Relay • How does relay switch ...
Automatic changeover switch • Automatic changeover s...
SUBSCRIBE TO THE CHUNNEL
contact me here
electreca.workshop@gmail.com
follow me on Twitter / davidssengendo
like my Facebook page / electerca
Visit my blog electrecasolutions.com/blog/

Опубликовано:

 

6 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 117   
@garylangley4502
@garylangley4502 Год назад
That is extremely easy. Thanks. When I had an appliance business, the motors had a start switch that would control the power to the start winding. If a motor is like that, switch the two wires that go to the start winding from the neutral and the start switch. I would do this if a motor in a dryer was defective, and I had an extra motor from a junk dryer that turned the opposite direction.
@evanslangatTV
@evanslangatTV 2 года назад
If we were taught in school like this,then It could be good.
@nolans1675
@nolans1675 11 месяцев назад
Thanks for this man, my journeymen told me to figure this out at home since I’m pretty new. This was a big help, cheers!
@patsonmachida4294
@patsonmachida4294 2 года назад
Thanks a lot, had hit a snag on my project and your video helped me
@Deetalks87
@Deetalks87 2 года назад
liked and subscribed, thank you for this, I was going crazy wondering why I had a pump spinning in BACKWARD direction, and now it's perfect, thanks. you da man.
@electreca1
@electreca1 2 года назад
Thanks for the sub!
@mosesmburugu7117
@mosesmburugu7117 9 месяцев назад
Thanks alot man. This is great. Very easy to understand.
@kadermaideen135
@kadermaideen135 7 месяцев назад
Even thought wires are not same color, just focus on the capacitor terminals and use ohm meter to check which one is conect to Life wire (black) accordingly to given schematic in video. It is very helpful. Many thanks.
@morgankpabitey1837
@morgankpabitey1837 Год назад
Thank you so much for the video. It has been really helpful. 👍👍👍
@electreca1
@electreca1 Год назад
Glad it was helpful!
@jesusbapt
@jesusbapt Год назад
Thanks. It's useful and you're a great teacher.
@electreca1
@electreca1 Год назад
Thanks for watching
@survivaluk6564
@survivaluk6564 2 года назад
Excellent informative vlog. Thank you David (electreca)
@electreca1
@electreca1 2 года назад
Glad it was helpful!
@vusimavimbela8764
@vusimavimbela8764 11 месяцев назад
Thanks Sir for a good explanation
@Theway64836
@Theway64836 Год назад
খুব সুন্দর, very nice and educational video, thank you.
@arwaelkasaby471
@arwaelkasaby471 Год назад
your explanation is great. Thanks a lot:")
@electreca1
@electreca1 Год назад
You are welcome!
@Nqaba-nv2if
@Nqaba-nv2if Год назад
Wow!! Thanks that's wonderful man.
@Zfmfs
@Zfmfs 2 года назад
Thank u dear... Very useful
@nujadragat3619
@nujadragat3619 3 года назад
thanks it helps a lot..
@randyschmittou8708
@randyschmittou8708 5 месяцев назад
Liked and subscribed. You are a Great Teacher. I have watched several videos on this. But your video was the best. I am going to make my chainsaw chain grinder work in both directions. Because it will sharpen the chain better when it sharpens into the tooth. Thanks very much!!!
@mikekasutson5262
@mikekasutson5262 2 года назад
Good teaching I learnt something I appreciate the knowledge 🙏
@venugopal-km4hf
@venugopal-km4hf 3 года назад
Hii bro I like your way of teaching and explanation good and could you do one video on synchronous motor?
@tonysmith1198
@tonysmith1198 2 года назад
Tops man thanks for the video
@marjanzarsof9804
@marjanzarsof9804 2 года назад
Nicely Done
@denicepark8652
@denicepark8652 Год назад
Thanks...big help for..
@ingenieurgod-la489
@ingenieurgod-la489 Год назад
Good job 🔥
@gibsontakadiyi1030
@gibsontakadiyi1030 3 года назад
Electrica you excellent in your trade I need to follow your steps
@dodznb238
@dodznb238 2 года назад
Hello my dear new friend,i like this information very clear, fully watched from philippines thank you for this sharing,👎🤝🙏🏼👏👇🏿👇🏿👇🏿👇🏿👇🏿
@electreca1
@electreca1 2 года назад
Thanks and welcome
@hassanmohd9163
@hassanmohd9163 5 месяцев назад
Thank you
@dennysnjagy9134
@dennysnjagy9134 Год назад
Amazing!
@eko364
@eko364 Год назад
thank you
@TTRVision
@TTRVision 2 года назад
thank you SIR!
@electreca1
@electreca1 2 года назад
Thanks for watching
@motoputz3201
@motoputz3201 Год назад
excellent!
@intimus500
@intimus500 2 года назад
thx ...very god video
@marcus_leon
@marcus_leon 3 года назад
If my source wire doesnt have different colors like somebody already replaced the wires before how will i know which wire is live or ground? Thanks
@tikzworld
@tikzworld 3 года назад
My capacitor of bolzano pump has 4 terminal..3 of which are used..blue wire, red wire and the other connected to live wire, which connection i should switch?
@marcostiantoni
@marcostiantoni Год назад
Hi. Thank you for your video. I have tried to revers two moror from old swimming pool pump. Single phase 0.75 KW. In revers the motor is slow and overloading. Please, could you give me your thought. thanks
@narendrakhona1168
@narendrakhona1168 2 года назад
MY UNDERSTANDING IS THAT STARTING COIL IS OF A THINNER GAUGE THAN THREE RUNNING GAUGE.. TO CHANGE ROTATION OF A MOTOR, ONE OF THE RUNNING OR STARTING LEAD MUST BE SWAPPED WITH PHASE OR NEUTER. PLEASE EXPLAIN.
@thepragmatic6383
@thepragmatic6383 Год назад
I wonder if using a 6-prong DPDT(double-pole, double-throw) switch could reverse the rotation of a 120V AC motor? This would allow the rotation of the motor to be changed with the flick of a switch.
@maxamuudsheexo6205
@maxamuudsheexo6205 3 года назад
Thank you for support l hope alot knowledge we support
@electreca1
@electreca1 3 года назад
Thank you too
@mbuthianjoroge9434
@mbuthianjoroge9434 3 года назад
Good job brathe
@electreca1
@electreca1 3 года назад
Thanks
@JokerdanFF
@JokerdanFF 2 года назад
Excellent
@ivanug5
@ivanug5 Год назад
Much appreciation brother the video has been helpful sir but I honestly request you to take me through size the capacitors for single phase motors ie run and start capacitors thanks
@electreca1
@electreca1 Год назад
Ok will plan on that.
@bxgaucho4762
@bxgaucho4762 11 месяцев назад
great!
@bashirbabatunde7559
@bashirbabatunde7559 6 месяцев назад
This can only work efficiently if both the running winding and the start winding have the same resistance which is not mostly the case in motor, but rather interchange one of the two starting coil terminals.
@kipkuruichumba5516
@kipkuruichumba5516 3 года назад
we are approciating ua work ,keep it up,and am asking ,i may have vedio that diplay rewinding of motor?
@electreca1
@electreca1 3 года назад
Yes, soon
@user-ek9sc2pb4t
@user-ek9sc2pb4t 6 месяцев назад
Pls what about the in and out on the pump ? It will remain the same?
@mthobisintshapha8048
@mthobisintshapha8048 2 года назад
Hwzit Sir what may cause three induction motor not to reverse even though I swap the phases?
@creativemind3562
@creativemind3562 Год назад
Is it possible to have a reverse -forward starter of a single phase motor?
@petermugambi9122
@petermugambi9122 2 года назад
Motor running forward, that's clockwise. Motor running backwards, that is anticlockwise. Good lesson though.
@linossinkala7840
@linossinkala7840 3 года назад
Super super thankyou
@electreca1
@electreca1 3 года назад
Welcome
@thomasgronek6469
@thomasgronek6469 Год назад
MANY thanks, you picked up a new subscriber. Could one just add a forward / reverse switch to the system to change the direction of the motor ?
@electreca1
@electreca1 Год назад
yes, it works perfectly
@thomasgronek6469
@thomasgronek6469 Год назад
@@electreca1 thank you
@nelaking1059
@nelaking1059 2 года назад
hi why do i need to do this? and when is the good time to do it? thanks
@ingenieurgod-la489
@ingenieurgod-la489 Год назад
En quoi est-il utile de changer la direction d'un moteur merci ?
@RadekXxx-mw4zx
@RadekXxx-mw4zx 2 месяца назад
Dobrze wytłumaczone pozdrowienia
@yusufadebayo348
@yusufadebayo348 2 года назад
Good day, how many amps breaker should be used to protect 1kw motor from over current
@YeshuaMuzic
@YeshuaMuzic 11 месяцев назад
I think your breaker size will depend on how much current the motor draws. A 1kw motor running on 230V would draw about 4A. Therefore you need a breaker rated above 4A.
@pjelectrcian8391
@pjelectrcian8391 2 года назад
Nice but before performing this practical make sure you measure coil resistance, both running and auxiliary winding resistance must be the same ohms value otherwise motor became overheat and for few time will burned out
@electreca1
@electreca1 2 года назад
Thanks for the tips!
@pjelectrcian8391
@pjelectrcian8391 Год назад
Ok
@prabhatheranga2739
@prabhatheranga2739 10 месяцев назад
How to use changeover switch please give us wiring diagram
@deanmav3571
@deanmav3571 9 месяцев назад
The Backward direction doesn't work properly is very slow and the coil becomes very hot ?
@pcg1276
@pcg1276 Год назад
It's not very clear, you have 2 flex cables belonging to the motor and a supply flex, what cores go where?
@mihrajmohamed2036
@mihrajmohamed2036 2 года назад
This is only suitable for running and starting coils have the same resistance.
@dantronics1682
@dantronics1682 2 года назад
its a 2 phase motor so both coils are the same reactance
@iotaaketioti2361
@iotaaketioti2361 2 года назад
how can you make a wiring to turn the motor forward and reverse direction without changing the wire from the motor
@electreca1
@electreca1 2 года назад
You can use FORWARD REVERSE STARTER. one contactor will have a forward direction connection and the other will have the reverse direction connection....you can watch this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-RDIchPs1rVY.html
@aarishcollection2437
@aarishcollection2437 2 года назад
@@electreca1 what you said is its just for 3phase how can you swap capacitor wires don't understand it seems you did explain it well
@dantronics1682
@dantronics1682 2 года назад
were you not suppose to discharge the capacitor before messing with it?
@kondwanibotha8217
@kondwanibotha8217 Год назад
Discharge it bro or give some time to let it discharge
@yesuanaokoamtumainiyeye1360
@yesuanaokoamtumainiyeye1360 3 года назад
Upo vzr mkubwa
@electreca1
@electreca1 3 года назад
Asante ....nashukulu.
@khadijaabas9894
@khadijaabas9894 Год назад
Hi! Nice and good video coz u meant helping I think, but be careful when educating people especially in powers such as DC, AC etc the way u know in reversing these motors is wrong. Thanks
@faackthewef
@faackthewef 2 года назад
I tried this today on my 1.1kw pump motor and it runs but makes a loud noise . What could be the problem?
@bollocknase
@bollocknase 2 года назад
Bearings maybe
@faackthewef
@faackthewef 2 года назад
@@bollocknase It has new bearings and on clockwise rotation it runs smoothly.
@bollocknase
@bollocknase 2 года назад
F Talks4U I’ve been looking into motors more, some starter windings has different resistant to run winding, so if it runs hotter it’s burning it out
@davidfinn8049
@davidfinn8049 3 года назад
If u hve a different color for the motor
@electreca1
@electreca1 3 года назад
Different colour? The colour of the motor doesn't matter, principles are the same regardless of less The only question would be WHAT TYPE OF MOTOR YOU HAVE. Op that answers your question.
@davidfinn8049
@davidfinn8049 3 года назад
Synchronous motor how will it be
@piusngibeyo5161
@piusngibeyo5161 3 года назад
Bro maybe you have a video on how to restore a used car wet battery
@electreca1
@electreca1 3 года назад
No, dont have any video on that.
@mikekasutson5262
@mikekasutson5262 2 года назад
@@electreca1 should we expect it
@Pre-m6s
@Pre-m6s 4 месяца назад
Is good work, but the motor don't change the direction check out the video you will see
@musangobi2079
@musangobi2079 3 года назад
Thought that capacitor is supposed to connected to axillary winding not the main winding
@samuellourenco1050
@samuellourenco1050 2 года назад
Depends. This is a split phase motor, which means that the coils are equal. There is no starting coil, as both are running coils. However, they are still 90º apart.
@skhan66
@skhan66 Год назад
That did not change the direction. It was doing cw before the wire change and is still cw after the wire change????
@picasso1212
@picasso1212 Год назад
Agreed…motor didn’t change direction, why are so many of you duped..?
@manikandanperumal5782
@manikandanperumal5782 Месяц назад
I think u have problem in u r home with earthing problem ❤
@gundur7193
@gundur7193 2 года назад
DC motor için nasıl bir yol izleyeceğim
@guyprimo6414
@guyprimo6414 6 месяцев назад
Doesn't make a difference if it's 110 volts or 220 volts
@bollocknase
@bollocknase 2 года назад
Think a earth wire would stop that static on mic 😁
@electreca1
@electreca1 2 года назад
Thank you
@jimmarchman
@jimmarchman Год назад
I can't hear him. Dang.
@temiarogodfrey8017
@temiarogodfrey8017 2 года назад
background music is too loud
@electreca1
@electreca1 2 года назад
Thanks for that , ill fix it
@user-wb9kn8tu1q
@user-wb9kn8tu1q 11 месяцев назад
QUESTION ONE In class, we have discussed the star-delta method of starting, as well as the forward and reverse control of a three-phase induction motor. In this test, you are being asked to draw the power and control circuits of a combined (single) circuit of the above highlighted methods of controlling a three-phase induction motor (i.e. Star-Delta Forward and Reverse control). Conditions: i. When the isolator and triple pole MCB is switched on, the circuit can be energized. ii. When the forward start button is pressed, the motor runs in the forward star and the delta. i.e. contactor coil (M), timer coil (T1) contactor coil (Y) are energized instantly and the motor starts running in forward star and later contactor coil (Δ) is also energized. iii. After a preset time (say 40 seconds) the normally closed of T1 opens while the normally of T1 open closes resulting in the motor running in forward delta. iv. When the motor is running in forward direction, a blue indicator lamp comes on. The contactors C2 and M2 are interlocks for the forward and reverse operation while contacts Y1 and Δ1, are interlocks for the star-delta operations. v. When the stop push button is pressed or an overload takes place, the motor stops running and the blue indicator lamp goas off. vi. When the reverse start push button is pressed, the motor starts running in reverse star and later in delta. i.e. contactor coil (C), timer coil (T2), contactor coil (Y) and later contactor coil (Δ) are energized. vii. After a preset time (say 40 seconds) the normally closed of T2 opens while the normally of T2 open closes resulting in the motor running in reverse delta. viii. When the motor is running in reverse (star-delta), a yellow indicator lamp will be on. ix. When the overload trips or a stop push button in pressed, the motor stops running in the reverse direction. how do u go about this
@anthonyrivera4797
@anthonyrivera4797 10 месяцев назад
He is showing how to reverse the rotation on a single phase motor NOT a three phase motor. To reverse rotation on a 3 phase motor switch any 2 leads.
@jasonsmith3573
@jasonsmith3573 Год назад
audio is broken at 1:07-2:0. not sure how legit the rest of the video is cause stopped watching
@electreca1
@electreca1 Год назад
Sorry about that.
@laciLaszloM
@laciLaszloM Год назад
Dude l watched the motor direction several times at the 10min mark and lm sure the direction of the motor is still in the forward direction......l don't think it changed direction
@johnokidi1957
@johnokidi1957 5 месяцев назад
😅😅😅 8:25 8:47 8:48
@arsenemweze484
@arsenemweze484 4 месяца назад
It works
@manikandanperumal5782
@manikandanperumal5782 Месяц назад
❌❌❌❌Bro it's really worked I saw. But here, easy way to change, I saw the real world function is very modification not change the winding they are change the winding polarities and change capacitor placing before phase and winding then winding and phase ❤
@adamarnold1551
@adamarnold1551 Месяц назад
Thank you
Далее
skibidi toilet zombie universe 37 ( New Virus)
03:02
Просмотров 1,9 млн
Survive 100 Days In Nuclear Bunker, Win $500,000
32:21
How to change rotation on a dayton 120 volt AC motor.
11:54
forward reverse switch wiring
7:26
Просмотров 52 тыс.
3 PHASE MOTOR TESTING - how too PROPERLY
39:04
Просмотров 25 тыс.
skibidi toilet zombie universe 37 ( New Virus)
03:02
Просмотров 1,9 млн