No video :(

How to Time any D-Series Honda engine

Подписаться 411

Просмотров 36 тыс.

50% 1

In this video I show how to mechanically time any D series engine (as well as show the different timing marks) and time the ignition with a timing light!
I had to time my winter beater so I figured I’d make a video about it as it’s hard to search for information on timing a B7 unless you have the Helms book.

Опубликовано:

26 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 42

@alexanderwilliams6301 2 месяца назад

Literally the best timing video for d series on RU-vid great camera work and commentary even years later. Thank you

@foxisretrofitting4556 10 месяцев назад

Thank you. I'm planning on buying a cheap old timing light to use on my cars and every video I've seen uses a fancy adjustable light procedure. I just needed a video showing a normal procedure with a cheap timing light and this video was exactly that.

@TDDungeon 3 года назад

This is the easiest and best timing video I've ever seen. Thank you

@jaymartin7119 2 года назад

Jenna are you not letting ted in

@DustinDiehl-qi4bt 5 месяцев назад

I'm curious about the d16 y7 is it the same as the demestion you just showed

@hadrianaugustus3547 3 года назад

Good video. It’s a lot easier with the tire off and extensions for the crankshaft pulley.

@yebo3061 3 года назад

True, but I could reach it pretty easily!

@zachengle5959 10 месяцев назад

Awesome video man. Love to see a clean del sol.

@tunertorquetv 6 месяцев назад

This video was awesome! Thanks 🙏

@chrisoliveira6941 3 года назад

Don't forget to ensure the vehicle is warm by holding 3k rpm until fans come on. Then check timing

@isaiahramirez1864 2 года назад

why does engine have to be hot for timing check?

@chrisoliveira6941 2 года назад

@@isaiahramirez1864 not sure exactly but it's stated in service manual.

@wokevroz Год назад

@@isaiahramirez1864 so the rpm’s can drop i think

@aterpay1826 Год назад

@@isaiahramirez1864 need to make sure the Car ECU is not using the cold engine map and it’s running at normal temp

@lewf5685 3 года назад

Great video!

@hinsonian Год назад

A+ young man

@Hasbeenshi9 8 месяцев назад

can you set the ignition timing without using a timing light?

@koopal1585 3 года назад

what will happen if you turn the CAM SHAFT GEAR counterclockwise instead of the CRANK SHAFT?

@arellano2611 4 года назад

My timing cover doesn’t have the little hole to loosen the tensioner is there another way?

@hadrianaugustus3547 3 года назад

There’s a plastic cap over the hole

@kaseone6896 4 года назад

Great video man!!! I have one question before I do all this do I have to have cylinder one all the way up or just do this process just ass you show it?

@kidnextdxxr 2 года назад

With the crank lined up it should b at top dead center

@kangokidkidd4037 3 года назад

How can you have 2 marks one for distributor and one for top dead center f23a1 engine Honda accord lx

@tommysandoval8241 3 года назад

Does the service port apply to my 89 Ef DX d15b2?

@skoomacat13 3 года назад

I changed my belt and my timing marks line up at tdc but i didnt adjust the ignition timing afterward since it was never mentioned in anything i read or any videos i watched, would that cause a misfire once it starts to warm up?

@yebo3061 3 года назад

It sounds more like an ignition coil to me, I've had plenty of those go bad. Does it hesitate occasionally when load is put on the engine?

@skoomacat13 3 года назад

@@yebo3061 i actually have new ignition coil in there. I didnt have any issues until i changed the belt. It ran fine for a few minutes until it started to warm up and the rpms started jumping.

@yebo3061 3 года назад

@@skoomacat13 if you don't have an ignition light you can just loosen the bolts and turn the distributor. I believe I had the same issue with this del sol, and advanced timing helped. (higher rpm)

@martinleon6450 4 года назад

Will the timing make the car not start

@ahunt 4 года назад

Turns over, but doesn't start? Yes its possible, especially if it's been messed with, but it would still usually spit and sputter or try to start even with the wrong timing. If it isn't attempting to start at all go back to the basics first, make sure its getting spark, and fuel.

@SalvageCivics 3 года назад

Try swapping around iat & iacv plugs?? You might have them crossed..

@bartlawson2650 2 года назад

Does this work for a D17?

@M3GAN3116 2 года назад

Is a D15B1 a interference engine? I think my timing belt may have slipped. Thanks 👍

@wtang912 2 года назад

From google I found all Honda engines are interference except the 3.0L and 3.2L

@M3GAN3116 2 года назад

@@wtang912 Thanks 👍

@celticlion 2 года назад

Does this work on a y8 non vtec with no marks? I'm doing a head gasket replacement and wanna make sure when everything goes back together there isn't any issues. Also how can you do the ignition bit without that tool?

@kaseone6896 4 года назад

You rotated the engine counter clockwise twice?

@yebo3061 4 года назад

christian dayrit as long as the timing marks are correct you will be fine. You’ll want to make sure the single line crank pulley) is at the timing mark. Yes you want to turn counter clockwise. You can message me if you have any more questions

@kaseone6896 4 года назад

Ty.. I set the timing marks and car just cranks.. do you have a way I can contact you other than this RU-vid?

@MikeKollin 3 года назад

I have a D15B7 Del Sol. Anyway to make it a little faster, more HP's... Like put a Different Header on it like a Vtech Head. I watched a video where this guy says he did that to his Engine.