Es muy ilustrativo para mi, aclararo que no soy sildador ni herrero, pero me gusta soldar para mi y aquí veo y leo todo lo que debo y no debo de hacer, gracias por sus enseñanzas 🙏
Está bien amigo, es soldadura básica y cómo dijistes, lo necesitas para hacer tus propios trabajos en casa. Los altivos no te van a mostrar ni lo básico , sigue viendo los vídeo de este sujeto y si te gusta la soldadura aprenderás lo bueno y desecharas lo malo. 💪💪
Короче сам по себе сварной шов должен быть чешуйками и красив . Тут же я увидел красиво когда зачистил всё "болгаркой" . Прям себя узнал , вообщем сойдет 😂
@@lloydcdannett5970 If this person were putting down floor tile, I could cut some slack, but he/she/ is building a canopy frame that will be supporting some kind of roof above people's heads. Work like this could get someone injured or killed. This person does not know how to weld and depending on the application, when people get hurt or killed because of their shoddy work, they are just proving their liability!! This person should take up another line of work. Maybe portrait painting or something like that where doing a shitty job, doesn't risk hurting people!!
You must not let the molten pool extinguish; when it goes out, the electrode's slag sticks to the metal. Keeping it hot pushes it forward and keeps it more isolated from the weld metal.
True. He could avoid slow vertical up all together with a quick down bead. That tube is thin asf and as long as u whip a bit to get a bit of arc on the work metal, and keep ~90 degree work angle you will easily penetrate with 75-95 amps. ThT tube is thin, penetration isnt even something you should have to think about. No uphill required. This is a beginner joint….
La soldadura es demasiado ancha, con lo cual se involucra material innecesariamente, y se calienta demasiado un material fino que se pandea con el sobrecalentamiento. Es mejor usar electrodo más fino ,sin bajar la potencia de la soldadora y moviendo la mano más rápido. Con eso quedará más chata y profunda con menos calor.
Shit welder sorry. Seen guys do runs on thin steel like that and weld once. You could also flip what you welding over. You only weld vertical if no choice.
Everyone always comments on welder’s work…. But nobody here has any of their own work posted…… just a bunch of cry babies who think they’re better than everyone else
Umm, that's what we reference in the trades as "hammered dog 💩". And, as bad as that was, then to grind the face off of it, that weld has no structural integrity, as if the porosity under that down handed stringer wasn't bad enough.
И не факт что есть провар. При такой толщине водить туда-сюда смысла нет. Как раз лучше точка в точку. Ну и зачищать если есть уверенность , что проварил.
Sometimes the welding specs say it must be ground flush or flat, in which case I hope it allows an open root weld so I can get inside reinforcement. In this case you are correct. Self taught mistake
Ты первым проходом просто положил дополнительный металл на тонкую трубу, а заварил вторым проходом. Я не сварщик, но тоже наверное так буду варить теперь профильные трубы 40×60, они совсем тонкие как фольга что то стали в этом году у нас в России.
Este amigo no sabe soldar corrido !! Eso es para principiantes ! Debe quedar bien a la primera vez. No pasar mas soldadura encima de otras. El perfil es de buen calibre comi para soldar punteado
I'm confused. First, you show it's wrong to go up in a zig-zack U-pattern. Then you demonstrate what we should actually do. Go up in a pinetree pattern. To the side, up to the center, back down to the other side, repeat. That's exactly how the guy who's currently teaching me welding recently taught me how to weld vertically accessing. But then that isn't what you actually do.
Dude what are you counting what the welds looked like, at my work you would get punched in the head if you tried to teach someone to weld like that, first of all you had too much current 2 your electrodes were too thick, or are you a beginner welder that you are trying to teach someone such mistakes..???
Just no. The weld needs to be a single weld your trapping the slag btween welds.
25 дней назад
Lui non è un saldatore e non potrebbe nemmeno fare il fabbro. Utilizza sempre il 6013( rutil) e non lo sa nemmeno usare. Fa questi video dove dimostra a tutti che non è capace facendo solo brutte figure. Io e i miei colleghi saldatori professionisti ci facciamo un sacco di risate quando guardiamo i suoi video. Non è che non conosce le tecniche di saldatura e proprio che gli manca il concetto stesso di saldatura. Inoltre non sa nemmeno fare la preparazione dei giunti da saldare . Non fate come lui perché la saldatura è tutt'altra cosa 😅
All'inizio saldi dal basso verso l'alto, poi dall'alto verso il basso. Mi hanno insegnato che in verticale si salda sempre dal basso verso l'alto per evitare che le scorie coprano il punto in cui si salda.
No actually lol. He should turn the heat DOWN and down pass with a 90degree work angle. Quick whip and pause will make a thin, standard diameter bead that will penetrate no matter what because its fuckin thin walled tube 😂. Silly comment brother
@@GrannySoupLadleexactly. Too much heat and standing too still with the stick are what causes burn through. This may be thin wall steel but it's not as thin as sheet metal.
I am red seal welder. Wrong. Because the steel is thin. Give a down hill weld once not to fast. Welder does not ground his weld. Only if you make a mistake. Is a person a welder or a grounder?
I love it thanks a lot keep teaching us I’m watching I want to weld stick and tig I’m getting back into the field and your videos help a lot. Thank you and may God continue to do great for you and your family well 💯🙏🏾
