How-To: ZL1 1LE Rear Spoiler Install // Carbon Fiber Wing

Подписаться 1,8 тыс.

Просмотров 6 тыс.

50% 1

How-To: ZL1 1LE Rear Spoiler Install // Carbon Fiber Wing
This video will cover how to remove the factory OEM spoiler from your 6th Gen Camaro with a post style spoiler (ZL1, SS, etc.) and replace it with the ZL1 1LE style spoiler. In this video we will remove the factory ZL1 spoiler and replace it with the Anderson Composites 1-piece Carbon Fiber ZL1 1LE rear wing.
Affiliate Links:
2016-2024 Chevy Camaro ZL1 1LE Full Carbon Fiber 1pc Rear Spoiler:
bit.ly/3PmA3uu
Milwaukee 1/2” Drive Socket & Wrench Set:
amzn.to/430BKlz
Milwaukee 3/8” & 1/4” Drive Socket & Wrench Set:
amzn.to/3Mztv98
10mm Swivel Wrench:
amzn.to/45QFas4
Magnetic Pickup & Tray Tool Set:
amzn.to/3P6sJlv
Panel Removal Tool Set // 200PC:
amzn.to/3qZCrOo
Plastic Blade Trim Removal Tool:
amzn.to/3EoHomX
3M Adhesive Eraser Wheel:
amzn.to/3R4Rlxq
3M 06394 // Strongest Automotive Adhesive Tape:
amzn.to/44CaZUv
LED Side Markers:
amzn.to/42RBzJ2
Lift Pads:
amzn.to/3s3FwtT
ZL1 Addons Premium Magpuck:
amzn.to/3KxA5MZ
Rotofab CAI for Camaro w/ LT4 V8:
amzn.to/43jSmW8
Rotofab CAI for Camaro w/ LT1 V8:
amzn.to/3ZRchbT
Corsa Extreme Axle Back Camaro V8:
amzn.to/3BSxdG3
Corsa Carbon Fiber CAI for ZL1:
tinyurl.com/wr8s4rx8
Silicone License Plate Frames:
amzn.to/3BMnoH5
Chapters:
0:00 - Intro // Overview
0:36 - Tools Needed
1:35 - Shout Out to Matt // Car Owner
2:00 - Pop the Trunk // Location of the Factory Bolts
2:30 - Removal of the Trunk Trim Panel // Bee Cameo
4:00 - Loosen the Factory Spoiler Nuts
5:40 - Squeeze Spoiler Clips // Outer Spoiler Posts Only
6:20 - Removing the Factory Spoiler
6:45 - Cleaning the Adhesive Off // Plastic Blade and 3M Eraser Wheel
8:15 - What Comes with the Anderson Composites Spoiler? // What Do I Need?
9:05 - How to Use the Indexing Posts // SS 1LE or No Factory Spoiler
10:25 - Placing the Weather Seals Around the Spoiler Bolts
11:00 - Installing the Anderson Composites Carbon Fiber Rear Wing
12:50 - Reinstalling the Trunk Trim Panel
14:05 - Reinstall Trunk Latch Cover
14:37 - Outro // Beauty Shots
These are affiliate links to the products. I make a small commission on anything purchased from my links.
**Disclaimer:
Due to factors beyond my control, I cannot guarantee against improper use of the information I share in my videos. (FollowMyLine17) assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not (FollowMyLine17) or any business affiliated to (FollowMyLine17).**

Авто/Мото

Опубликовано:

3 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 53

@heyitsnick6648 7 месяцев назад

Such an easy tutorial as you explain everything. Other people just put it on and say stuff but you show us, thanks. Cant wait to get a Camaro and come back to this video😂

@FollowMyLine17 7 месяцев назад

Thank you! Glad it could help!

@Cryptoinvestor-pv4fy 10 месяцев назад

Good looking wing, loved the detailed instructions.

@FollowMyLine17 10 месяцев назад

Thanks!

@Mikeselchow 10 месяцев назад

Glad to know there’s another zl1 in Minnesota. I’ve only seen 1 other and it was a convertible

@c4sare4kiddos 10 месяцев назад

What color was it

@Mikeselchow 10 месяцев назад

@@c4sare4kiddos it was black. I have the radiant red tint coat

@FollowMyLine17 10 месяцев назад

There is a silver convertible in the Waconia area too.

@Mikeselchow 10 месяцев назад

I see mustangs,chargers & challengers all day. It’s nice to see that Camaros are harder to come by

@c4sare4kiddos 10 месяцев назад

@@FollowMyLine17 I have the satin steel vert, diff state tho. There’s so many different gm silver” paint codes tho so it’s hard to tell even for me, lighting ppf cleaning etc make it look different where I confuse it with some ppl online/ irl who have the different paint codes of that silver or gray. I think I have never seen Arctic blue or silver or whatever they call it irl on any trim and that’s it.

@matt-ts8cx 10 месяцев назад

Lools good, glad mine came with this! I like the black post on the stock one better than the carbon fiber post. I might just be use to the stock version but the carbon fiber post look out of place.

@FollowMyLine17 10 месяцев назад

I love the carbon posts on this wing, but I think I’d take one either way!

@fearless798 9 месяцев назад

I've been thinking about adding this wing to my ss

@FollowMyLine17 9 месяцев назад

Do it! You won’t regret it.

@fearless798 9 месяцев назад

@@FollowMyLine17 did you have any issues with extra holes in your trunk ?

@FollowMyLine17 9 месяцев назад

@@fearless798 well we added this wing to a ZL1. You said SS so I a regular SS should use the same holes. If it’s an SS 1LE, you’ll have a bunch of extra holes, and then you’ll have to drill the new ones for the ZL1 1LE wing.

@RacingforALS 9 месяцев назад

Great video. Having done this myself, a big warning is to not drop the nuts into the body of the trunk lid. You can do this by taping the socket to the nut or lowering the lid enough that they will fall free. Otherwise, you may have to fish them out with a magnet.

@FollowMyLine17 9 месяцев назад

Great call out. I think I had it in the original cuts, but it didn’t make the final video. I did use a magnet to grab the factory nuts out and put them on.

@RacingforALS 9 месяцев назад

@@FollowMyLine17 Knowing is half the battle. 😁😁

@RacingforALS 9 месяцев назад

Additionally, 50% iso alcohol works better than detail spray for removing adhesive and is paint safe.

@FollowMyLine17 9 месяцев назад

I was using a plastic blade and the eraser wheel to remove the adhesive, so I wanted more lubricity. I actually hit it up with IPA as a final step before I installed the new spoiler.

@luisosorio8954 2 месяца назад

I have an LT RS I want to put the same spoiler on it but I don't know how to cover the holes left by the previous spoiler. What do you recommend?

@FollowMyLine17 2 месяца назад

The best way is to try to find a trunk lid without a spoiler or with the standard SS, or ZL1 spoiler from 2018+, which has the reinforced braces within and have it painted. 2016 and 2017 do not. Otherwise you could have a body shop fill the holes. Otherwise you could just use some plastic plugs and paint them to match: amzn.to/3JyQsbE

@mohamedelsherbiny7570 3 месяца назад

Can you tell me what the dimensions of the screws in the mounts are?

@FollowMyLine17 3 месяца назад

Which dimensions are you referring to? Each screw in each post, or from post to post?

@user-se5mm8xt8o 7 месяцев назад

Does anyone know if you could put this wing on an rs?

@FollowMyLine17 7 месяцев назад

You can put the wing on anything. In the video I show you how to use the indexing post. Does your RS have the post spoiler, blade spoiler, or no spoiler?

@FromDust81 6 месяцев назад

Did the new wing come with adhesive tape? And to loosen the old wing adhesive what did you use?

@FollowMyLine17 6 месяцев назад

The new wing came with adhesive foam. To get the old stuff off I used a plastic scraping blade and a 3M adhesive removal wheel attached to a drill.

@BeatTheD3viL 9 месяцев назад

hey... forgot to show the roof top rear view camera view before and aftere wing install. Great video, nevertheless. Cheers.

@FollowMyLine17 9 месяцев назад

With the camera angle all the way down, on the furthest out camera view, you can see the wing. In the mid setting, you can barely see the top of the wing at the very bottom of the mirror, and at the closest zoom setting, you can’t see the wing at all.

@P-Dawg-01 6 месяцев назад

Nice job and nice looking wing! What did it do to your rear view camera view?

@FollowMyLine17 6 месяцев назад

Zoomed all the way out, you can see the top of the wing across the bottom third of the screen. Mid zoom it’s just barely across the bottom and zoomed all the way in, it’s not in view at all.

@P-Dawg-01 6 месяцев назад

@FollowMyLine17 OK awesome! Thank you for the info! Did the new wing have 3M adhesive to secure as well as cushion the supports of the wing to your trunk lid?

@FollowMyLine17 6 месяцев назад

@@P-Dawg-01 it came with foam tape

@appel199 3 месяца назад

I would like to put this wing on a convertible ZL1. Any suggestions on what to do with the wing mounted camera that comes on the convertible?

@FollowMyLine17 3 месяца назад

Wildhammer sells a 1LE style spoiler with a camera hole in it. It is made by EOS, so it’s a bit different than this one, but in 2019 the rear view camera on the ZL1 1LE was in the spoiler itself. If you use the wildhammer link in the description, you can then search the shop for it.

@appel199 3 месяца назад

Awesome. I should be taking delivery of my 2023 rapid blue ZL1 convertible very shortly. The only thing it's missing is the performance data recorder. Any suggestions on a good one with camera I can add? Thank you very much.

@FollowMyLine17 3 месяца назад

@@appel199 this is an older video but many of the items are still current. Links for everything in the description too. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-GGOSnBjibwk.htmlsi=8E-VKrgGrhozbJiD

@appel199 3 месяца назад

Thanks. Just so bummed that one PDR option is not on the car. But really looking forward to getting the car. tho.

@FollowMyLine17 3 месяца назад

@appel199 ⁠stay tuned… I’m working with some folks on an OEM retrofit option. Late 2024 hopefully.