Тёмный

I Broke My DANA 60 Axle Housing... Don’t Let This Happen To Yours!! 

JK Gear and Gadgets
Подписаться 146 тыс.
Просмотров 25 тыс.
50% 1

A few videos back, we took the JKU out for some high speed offroad testing. It did great, or so i thought.. At least we caught this issue early before it fully started to separate, which is unfortunately fairly common on these axles. I have had this axle setup since 2019 and they have done amazing! They however are not bulletproof (As found out from 40mph Ultra-4 course lol). The Barnes4wd Truss did a fantastic job holding everything together, and hopefully we can bend it back to spec and reweld it in place! To prevent this from happening again, Mike and I came up with a little lower mini truss for the axle. This will tie the diff and the tube in on the lower section, hoping to spread the load away from the pivot point on the tube/weld. We have to keep in mind that when we swap these axles into a linked suspension, we need to remove cast from the housing to weld our control arm mounts and shocks. By doing this, we naturally make the axle a little bit weaker. Some people will accidently cut too deep into the cast and score the tubes as well. This can also be a cause of something like this, if not much worse. In my case this wasnt the issue, and i did address to avoid that in my video playlist. I think we just took too big of a hit, too fast, without race suspension. So, my recommendation.. Truss, Weld Tubes, Tie in lower tube somehow. Im stilll a big fan of Junkyard axle builds, but im always welcome to finding improvements in spots that might need addressed.
Stay tuned for a 4 year review with these DIY axles! And of course an axle comparison video one the 2 door Crate axles arrive.
I would love to have pulled the axle and repair it correctly, however i am assisting Jeep Jamboree at Crossbar and need the JK ready to roll!
Garage Tools and Equipment:
Balljoint Press: amzn.to/3BHmYpj
M18 Impact: amzn.to/3JxDKZS
M18 Cheap Batteries: amzn.to/3BBXuta
Portable Work Platform: amzn.to/3bxD35Y
Crows Foot Wrench Set: amzn.to/3GEQyxb
Torque Wrench: amzn.to/3oQluS0
Allen Socket Kit: amzn.to/3JqpB0k
Crocs: amzn.to/3r7YXS4
Affordable Plasma Cutter: amzn.to/3H0eBqY
GoPro: amzn.to/3jZ1D0e
Interior Trim Removal Tool Set: amzn.to/3unUdce
Jeep Stuff:
Jeep JK Sunshade: amzn.to/3d2jBi8
Soft Shackles: amzn.to/3q0Y3FY
OBD2 Bluetooth Reader for JScan: amzn.to/3R7Tt4B
JK Grab Handles: amzn.to/3RgmTxO
JL/JT Grab Handles: amzn.to/3Rd6aLC
Warn Dana 60 Locking Hubs: amzn.to/3vzSWjs
Warn Zeon 10-S Winch: amzn.to/3AJR9tw
Magnaflow Muffler: amzn.to/3CQgg0O
Jeep JK Remote Start Kit: amzn.to/3XYjC9R
JKU Bedrug Kit: amzn.to/3DhWFFZ

Авто/Мото

Опубликовано:

 

18 апр 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 111   
@JKGearandGadgets
@JKGearandGadgets Год назад
She took it like a champ and we are ready to roll back to Crossbar Offroad Ranch to help out with the Jeep Jamboree there! Stay tuned on the JK build and what all these crazy parts mean! Thanks for watching, and make sure you turn on channel notifications if you want to stay up to date with the JK build projects 🤙🏻
@angelmvniz
@angelmvniz Год назад
When is that jamboree thing happening?
@22yoshifan
@22yoshifan Год назад
Drill out those plug welds in the housing and redo them. I added in more with my 8.8 Swap so it wouldn’t spin the tubes.
@randygreen7871
@randygreen7871 Год назад
Your knowledge and abilities never cease to amaze me! I've learned so much from watching your videos, thank you so much for sharing.
@keithbrown4243
@keithbrown4243 Год назад
Nice work Ben. Your mom was here for supper tonight, we cooked Hibachi and invited her to join us for mothers day. Keep up the good work.
@donnieh174
@donnieh174 Год назад
You have given me tons of ideas of how I want to continue building my rig. Just have to find the funding to start really buying parts. However I felt you pain as you watched the bolts go flying every where.
@av8orAH64
@av8orAH64 Год назад
I married my high school sweetheart and we have been together for 40 years. I like your family and applaud your commitment to them and to your passion for Jeeps. Well done Sir!!!!!!
@that68lifestyle
@that68lifestyle Год назад
Right about 11:50 in the video, Ben is contemplating his recent life choices. 😮
@pugs13
@pugs13 Год назад
This is why I watch all your videos you never know what you will pick up on. That bucket trick for dismounting the bead locks saved me like 40 minutes over 5 tires instead of fighting them standing up makes the tire pretty much fall right off. Keep making these awesome videos
@jlautomotive6349
@jlautomotive6349 Год назад
Another great video and looking forward to these future projects! Love how you actually use your jeeps and looking forward to the V8 swap as well!! 👍
@ShizzyIzzy1
@ShizzyIzzy1 Год назад
Had such a blast with you guys at Crossbar this weekend!
@jeffcombs8237
@jeffcombs8237 Год назад
Solid advice. It will handle what it's built 💪 for.
@jeepfamoverland
@jeepfamoverland Год назад
That must have been a good hit for sure! We had ours out in Johnson Valley ripping through the desert and now I want to go look at my axle 😆
@onebridge7231
@onebridge7231 Год назад
Rock crawl = fun. Rock run = your day is done! 😏
@JKGearandGadgets
@JKGearandGadgets Год назад
Haha that’s a good one!
@av8orAH64
@av8orAH64 Год назад
Go Coasties. I loved working with the USCG. Cheers brother.
@StormbornJKU
@StormbornJKU Год назад
I look forward to the 2 door build!!!
@jonjalbert1922
@jonjalbert1922 Год назад
Can't wait to see what you have coming for the two door :)
@AntonioPerez-kk8cj
@AntonioPerez-kk8cj Год назад
You should leave some space on the repair lower plate for water drainage in case water ever gets in there.
@PhillipScull
@PhillipScull Год назад
Nice 😊 ❤ cool to see mor videos coming 😀 congrats
@jonathonmarquez6644
@jonathonmarquez6644 Год назад
I can’t wait for the 2 door videos to come. I’m still in the fence on which way I want to go ls or hemi with mine.
@fogstain
@fogstain Год назад
Dangit! Right when my checklist was about all crossed out!
@chrisgardner1431
@chrisgardner1431 Год назад
I bent a wheel the same way and fixed it with a 4x4 wood block and bottle jack and some heat on the wheel. Straightened it out enough no one could tell and zero balance issues on the highway. 👍
@offgridrecon
@offgridrecon Год назад
Always great info. 👍🏻❤️🇺🇸
@bayani3
@bayani3 Год назад
Oh man when that tire fell over it was like scripted hahaha hope it didn’t take long find all the screws. Amazing videos as always!!
@matty86suk
@matty86suk Год назад
I have 2 rigs with SD 60s swapped into that i need to build these gussets for.. The artec truss welds to the inner C and might take some of the moment off the tube.
@thetouchtonsoffroad3574
@thetouchtonsoffroad3574 Год назад
Maybe you could plug weld the hole in the casting
@hdrider2071
@hdrider2071 Год назад
When it rains it pours my friend. Only two situations that jumping a jeep is ok...its your buddies that is sleeping with your ol lady and rentals😅
@user-vy5pb2vb5r
@user-vy5pb2vb5r Год назад
You should come out to Rugged Mountain Ranch for the Tackett creek challenge memorial weekend watch the races and check out the park. It is just south of Hartshorne OK
@philipwhatley6742
@philipwhatley6742 Год назад
Goodness the amount of pressure that thing had to have taken to crack that
@schwanzmunster2503
@schwanzmunster2503 Год назад
Great upgrade and fix. What stops the passenger side from cracking? Wouldn't a longer tube cause more leverage on the welds on the center section?
@ironbearjku2233
@ironbearjku2233 Год назад
Ben, we gotta wheel soon, we were both stationed in Virginia and spoke but never met up now I’m in Kansas and your in Oklahoma about hour and a half away hahaha Look for a black 4 door JKU mountain on tons at crossbar sometime
@fergotti
@fergotti Год назад
How are you enjoying OK life? I hope you avoided the storms
@GarageGeek
@GarageGeek Год назад
Would it be wise to leave the oem housing intact in that area in future swaps? Does cutting off the housing serve a purpose?
@thomasleonard9685
@thomasleonard9685 Год назад
What happens if you need to replace the “c”? That’s going to be work. Love your stuff. Like to ride with you sometime
@calebsurpass
@calebsurpass 2 месяца назад
Hey - Just wondering about the front SD 60 - a lot of places say 05+ ... until what year is that + good until what year? or even further? I've seen some people say that they have an 11' with 5.38 gears. Got a few deals with years all varying - just wanted some confirmation to make sense of it all. Thanks man and amazing to see the whole series.
@Jeff-wu6wn
@Jeff-wu6wn Год назад
You should check the axle seal and fluid since you heated up that axle so many times and up high temps?
@jamesgorman1676
@jamesgorman1676 6 месяцев назад
Did you make anymore of those lower driverside brackets ? I would like to have some.
@TheRambler-pz1gx
@TheRambler-pz1gx Год назад
The reason that side cracks inst just because of the removed casting. The tube & truss is really short there. This means there is no material to dissipate the shock load.
@richardkucklick5284
@richardkucklick5284 Год назад
Are you coming down to Jeep Beach Week?
@2555brandon
@2555brandon Год назад
I may notch my truss to keep from cutting the cast
@jesseyjulson1967
@jesseyjulson1967 Год назад
Lol I don’t think I’ve ever heard quick beadlock change before 😂
@stinkymcstinkerton1854
@stinkymcstinkerton1854 Год назад
Me neither. I’m down to about 25 minutes per wheel . 4 pssses torque.d
@paulcmad
@paulcmad 7 месяцев назад
Curious if you suspect the truss was partially the cause here? Wonder if the truss was already applying a bunch of upward force to the axle tube and when you got rowdy it added enough additional strain to pop that axle tube. Nice work.
@JKGearandGadgets
@JKGearandGadgets 7 месяцев назад
Negative. Otherwise there would be a lot more truss related failures. This is from removing the cast diff section on superduty 60s
@paulcmad
@paulcmad 7 месяцев назад
gotcha makes sense @@JKGearandGadgets
@kingranch8516
@kingranch8516 Год назад
Just a question do you need to worry about seals with that much heat?
@frdmbros
@frdmbros Год назад
I have a 2012 jk with a blown head gasket what would you recommend doing to the motor while I’m at it
@joshup
@joshup Год назад
I was just going to ask you what dana axel should I go with, with a hemi on 37s. Lol and I see this...
@michaelhelwig96
@michaelhelwig96 Год назад
My only question is aren't you cooking the inner seal and or fluid that close to ring and pinion.
@MS-kh2je
@MS-kh2je Год назад
Cut out some steel crescents the radius of the inner wheel and mount them to the end and base of a bottle jack and push that wheel back into shape
@seanmesaehable
@seanmesaehable Год назад
i have the same setup as you. i would by lower reinforcement brackets from you
@bretthormahlen3524
@bretthormahlen3524 Год назад
I noticed that you didn't drill out the ends of the crack to prevent it from growing. Nice repair though.
@millstonejeepworx
@millstonejeepworx Год назад
Dayum. That had to be a hell of a hit. On the 2dr, are you going to stretch it?
@JKGearandGadgets
@JKGearandGadgets Год назад
Yes it will be stretched but not in the typical way. more on that soon!
@SolosHold
@SolosHold Год назад
Haha, what caused it. I gotta good idea
@gogerwi
@gogerwi Год назад
Ben, off point I know but which exhaust did you and Cassy go with on the LS in the LJ? The Holley/ Hooker stainless or cast? I'm looking for the discontinued stainless "Y" pipe.
@JKGearandGadgets
@JKGearandGadgets Год назад
Stainless. Not sure why they discontinued it, very nice kit
@Jeeptalkshow
@Jeeptalkshow Год назад
I'm surprised you need to truss a Dana 60. Oh wow it is trussed!
@moejr14
@moejr14 Год назад
Does the axle have inner axle seals?
@stinkymcstinkerton1854
@stinkymcstinkerton1854 Год назад
For those interested, both Carli and Thuren offer a lower truss for Ram Dana 60 front . They may make one for superduty or may be able to modify the Ram version. Bombing the mega cab in the desert is fun from time to time 😅
@JKGearandGadgets
@JKGearandGadgets Год назад
Only issue is they are designed around the factory cast I think. Our trimmed cast and control arms get in the way
@stinkymcstinkerton1854
@stinkymcstinkerton1854 Год назад
@@JKGearandGadgets I don’t think the Ram diff has the casting so far over on the driver side. I’ll have to check when I get home. I think some kind of mod might be necessary. Plus it’s going to hang lower on the pass side. I’m glad you posted about it. I now plan to reinforce my jeep front on the low side.
@adidas4275
@adidas4275 Год назад
grab some trailready beadlocks and be done with wheels. Mine are 13 years old, been in a 40 mph accident and taken many hits over the years and still in great shape
@redcanyonoutdoorquest6220
@redcanyonoutdoorquest6220 Год назад
As a CWI (Certified Welding Inspector) and professional certified welder, I highly recommend that you do NOT weld on that axle housing anymore if that’s the best you can weld. At a quick glance, I noticed the weld before you started grinding on it. If you’re going to use a 6010 type of rod, you better do another filler pass with a low hydrogen rod to cap it off. That’s why it cracked on you. All that undercut left from that weld actually left your housing weaker than it originally was. Congratulations.
@dragop5698
@dragop5698 Год назад
Any chance the axle seals melted with all that heat
@jtadams8500
@jtadams8500 Год назад
I am not a professional welder. I see a lot of people using wire feed welder’s on axle builds. I would think maybe mig stick welders would make a lot stronger welds due to better penetration of thick axle tubes. Wire feed has always seemed for more light duty welds and axles are definitely and heavier duty weld.
@user-jq2sw5oz2q
@user-jq2sw5oz2q Год назад
Forgive my ignorance but why couldn’t yo leave the casting and cut the truss so you don’t lose that strength?
@beaumont9072
@beaumont9072 Год назад
America 🇺🇸 💪🏼
@TwistedOff
@TwistedOff Год назад
👍
@ShawwwHa
@ShawwwHa Год назад
I can answer all your questions concerning the cause of the broken axle with two words, lead foot. And the question of how to avoid a broken axle can also be answered with two words, light foot.
@JKGearandGadgets
@JKGearandGadgets Год назад
But if it was an aftermarket crate axle would it have cracked? If i had this truss on would it have cracked? Thats what i want to know.
@ericwheeler5637
@ericwheeler5637 Год назад
@@JKGearandGadgets not much can handle a big hit at high speed honestly.
@zxtuner4lyfe
@zxtuner4lyfe Год назад
​@JK Gear and Gadgets ben i'm wondering if it's because just standard mig er70s wire was used? I think ni55 Is the proper thing to use. It's possible the weld was too brittle and started the crack. When I welded the tubes recently on my 14 bolt no matter what I did mig started to crack so I used that ni55 and it's perfect.
@zxtuner4lyfe
@zxtuner4lyfe Год назад
But I want to know too if the crate would have survived. Fusion has s60 housing for under 3 grand.
@jonocalvert2196
@jonocalvert2196 Год назад
Good morning. Did you shave the 14 bolt or dana 60 up front
@JKGearandGadgets
@JKGearandGadgets Год назад
Did the Barnes 13 bolt diff cover shave.
@brandoncroucher4572
@brandoncroucher4572 Год назад
I doubt this will get out to you but take a bottle jack in the rim on a piece of wood and pump out the bend in the rim
@redbarry2540
@redbarry2540 Год назад
Advance Driveline Axles ….?
@TheRambler-pz1gx
@TheRambler-pz1gx Год назад
If you can trace this truss out on paper I can scan it,and draw it up in CAD for upload to a file share, or even make a printable scale PDF.
@OnTheSideOff-Road
@OnTheSideOff-Road Год назад
Don’t you need to worry about your seals with that much welding and hear while it’s all together???
@CrucesNomad1
@CrucesNomad1 Год назад
What gears you running on that one ton please?
@JKGearandGadgets
@JKGearandGadgets Год назад
5.38
@apexpredator_jku
@apexpredator_jku Год назад
Lemme guess which crate axles you're going with... Advanced Driveline?
@JKGearandGadgets
@JKGearandGadgets Год назад
You’ve been a good guesser before as well 🤙🏻
@Cstepp
@Cstepp Год назад
Why when you could go with east coast gear supply which makes the axles for advanced for cheaper
@philipdagariero5383
@philipdagariero5383 Год назад
​​​@@Cstepp connect the dots... Offroad Elements = Advanced Driveline. They've been featured on this channel numerous times. Ben's is or once was a Brand Ambassador for them therefore what you might pay for those axles & what it would cost him are 2 very different things.
@nicholascooper1193
@nicholascooper1193 Год назад
*cuts away the factory casting* “Known weak spot”… imagine that
@av8orAH64
@av8orAH64 Год назад
I think you guys are closet metallurgists...Wow!
@ShaunsJeep
@ShaunsJeep Год назад
A few things to note the axel itself was not a fault but who ever welding it was.. The shortening of the axel not likely. I can tell you 1000% was the welds of that that failed. Welds like that are not only terrible but dangerous. Be careful.
@JKGearandGadgets
@JKGearandGadgets Год назад
Some people don’t even weld the tubes back. In my opinion it was the shortening of the axle, as well as a lot of professionals opinion on this axle.
@JKGearandGadgets
@JKGearandGadgets Год назад
Naturally yes the weld failed, but if it wasn’t there the axle would have snapped in half
@jessedavis4699
@jessedavis4699 Год назад
Like my wife always says, stupid hurts 😂
@motoboggin2619
@motoboggin2619 Год назад
i would do a root pass then 2 stringers over the top all while its been preheated, you already burned the hell outta that axle seal and carrier bearing, might as well put a real weld on it. i dont understand why youre scared of heat cycling when your already beyond that point with the torch.
@John-uo1qf
@John-uo1qf Год назад
Another option is to slow it down a bit. 😂
@tomhubbard353
@tomhubbard353 Год назад
Jeeps don't have wings so they don't fly! Make them fly, you will cry. LOL You heated the piss out of that housing, the next failure is probably going to be the inner seal you melted LOL
@JKGearandGadgets
@JKGearandGadgets Год назад
I’d rather change out the seal than have a split apart axle on the trail haha. Luckily the 60s are thick and dissipate heat away from the seals pretty well
@tomhubbard353
@tomhubbard353 Год назад
@@JKGearandGadgets I was just saying you should probably change out the seal since a considerable amount was put into the casting and was absolutely necessary for welding cast. I highly dislike oil leaks and axle tube leaks are suck a PIA to clean up and deal with. PS after reading my msg, I can see where I failed to communicate well, my apologies.
@okiesoonernews4645
@okiesoonernews4645 Год назад
Had to pause the video to hide from tornadoes
@JKGearandGadgets
@JKGearandGadgets Год назад
Glad you’re safe!
@vavendano2000
@vavendano2000 Год назад
good video, but here's a suggestion for axle longevity.......maybe dont bash it up onto the rocks so hard.....but i dont know. im just sayin'....lol
@JKGearandGadgets
@JKGearandGadgets Год назад
Haha I mean you have a point, that’s a 100% foolproof plan lol
@Escape.Idiocracy
@Escape.Idiocracy Год назад
Dude - you forgot to mention recommending side by side stuff is best done in sxs or KOH built jeep…. Jeep is best left to keep stuff. 🤣😂🤣
@gettinbentfabrication9137
@gettinbentfabrication9137 Год назад
Should have cut the truss it would have pulled down with less force and then welded the truss back up
@JKGearandGadgets
@JKGearandGadgets Год назад
We thought about that! But need the jeep asap for jeep jamboree at crossbar to help out lol
@krisbarnard1684
@krisbarnard1684 Год назад
Thats the issue with low profile trusses... they arnt actually trusses
@Sniperssx
@Sniperssx Год назад
So strang UD60 with full support get cracked
@darkenfly32
@darkenfly32 Год назад
And the next video will be how to change your axle seals because your seal looks like bacon 🥓,,,,, 🤣
@JKGearandGadgets
@JKGearandGadgets Год назад
No issues with the seals the first time I welded this up. The 60 is so thick the heat dissipates before the seals can get damaged
@pranays
@pranays 7 месяцев назад
A rosette weld inside the port you saw the half moon?
Далее
How Much Did My “Junkyard” 1 Ton Swap Cost??
24:05
Yes or No Fruit Shake for My Son #cooking #shorts
00:41
When Should You Upgrade Your Axles? - Coffee One-Take
25:00
My Jeep Wrangler DIY Hemi Swap Cost HOW MUCH???
21:36
Просмотров 214 тыс.
THIS is what makes the Dana 60 so great!
17:41
Просмотров 61 тыс.
How to Re-Gear A Jeep Gladiator/Wrangler JL Axle!
29:07
Camry rear hub replaced #carpart
0:36
Просмотров 8 млн