Тёмный

What Are Ball Joint Deletes And How Do You Install Them??? 

JK Gear and Gadgets
Подписаться 145 тыс.
Просмотров 289 тыс.
50% 1

Ball Joint Delete Kits: americanironoffroad.com/
Most Jeep owners are fully aware of how much Balljoints can be a pain! With our larger tires, and heavy offroad use, the factory balljoints are just not up to the task and fail quickly. Even aftermarket balljoints have a hard time staying tight and reliable.. Its mostly due to the fact that the Balljoint design itself leaves a lot of room for improvement.
Some of you may be familiar with Balljoint Deletes, and some may have never heard of them! Ive gotten a ton of requests for this video, not only the install part, but to also explain what in the world Balljoint Deletes are and why they are better.
Head over to American Iron Offroads website for more info, and to see all the axles they produce kits for. Or, check out the facebook page to see real world reviews, questions, testimonials, and feel free to ask any questions you would like! / about
Balljoint Deletes are not much harder to install compared to a typical balljoint job. But either way, its not a quick simple job... And its nice to know that we wont have to do this job over and over compared to a typical ball joint replacement.
In a way, these are kind of like a hybrid kingpin setup.. Some of you are familiar with a kingpin and know that they are very reliable and strong, some people refuse to own an axle that has balljoints! With this setup, we replace the tapered ball joint with the ball in socket design and swap over to a Spherical Rod Bearing setup that sits in a machined cup housing with a through bolt.
In this video i install a set on my 2005 Ford F250 Dana 60 Axle that i swapped into my Jeep, however they make kits for quite a few other offroad axles as well. In the future, i plan to install a set on JK axles that we have under Cassies LJ.
If you are looking for the strongest "Balljoint" Upgrade, then these right here are what you need. Whether you are in need to replace worn out Bjs, or just looking to avoid future failures then i would highly suggest giving these a try.
Balljoint Press: amzn.to/3BHmYpj
M18 Impact: amzn.to/3JxDKZS
M18 Cheap Batteries: amzn.to/3K5C1fm
Portable Work Platform: amzn.to/3bxD35Y
Jeep JK Sunshade: amzn.to/3d2jBi8
Torque Wrench: amzn.to/3oQluS0
Allen Socket Kit: amzn.to/3JqpB0k
Warn Dana 60 Locking Hubs: amzn.to/3vzSWjs
Garage Tools and Equipment:
Tire Balance Beads: amzn.to/4bngbPR
Electrical Deustch Connector Kit: amzn.to/3thO3Nq
Balljoint Press: amzn.to/3BHmYpj
Digital 1/2" Drive Torque Wrench: amzn.to/3RU4lq2
M18 Impact: amzn.to/3JxDKZS
M18 Cheap Batteries: amzn.to/3BBXuta
Portable Work Platform: amzn.to/3bxD35Y
Crows Foot Wrench Set: amzn.to/3GEQyxb
Torque Wrench: amzn.to/3oQluS0
Allen Socket Kit: amzn.to/3JqpB0k
Crocs: amzn.to/3r7YXS4
Full Torx Bit Set: amzn.to/3rGMxnC
Affordable Plasma Cutter: amzn.to/3H0eBqY
GoPro: amzn.to/3jZ1D0e
Interior Trim Removal Tool Set: amzn.to/3unUdce
Grease Gun Tip Attachment: amzn.to/3J64lNW
Jeep Stuff:
Jeep JK Sunshade: amzn.to/3d2jBi8
LED Headlights: amzn.to/3LOzqHZ
LED Tail lights: amzn.to/3PFtLVK
Soft Shackles: amzn.to/3q0Y3FY
OBD2 Bluetooth Reader for JScan: amzn.to/3R7Tt4B
JK Grab Handles: amzn.to/3RgmTxO
JL/JT Grab Handles: amzn.to/3Rd6aLC
Warn Dana 60 Locking Hubs: amzn.to/3vzSWjs
Warn Zeon 10-S Winch: amzn.to/3AJR9tw
Magnaflow Muffler: amzn.to/3CQgg0O
Jeep JK Remote Start Kit: amzn.to/3XYjC9R
JKU Bedrug Kit: amzn.to/3DhWFFZ

Авто/Мото

Опубликовано:

 

17 май 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 472   
@cznkane
@cznkane Год назад
I have these on my JK axled LJ and love them, no issues at all and the steering feel is fantastic. Running 40" tires, no stabilizer, and 60 down the highway without issue (that's about all she'll do lol)
@MrGoldman9
@MrGoldman9 Год назад
Thank you for this beautiful episode, and the most beautiful thing is that you put a link to all the equipment and pieces that you used to facilitate the search for and purchase. Thank you again, wishing you safety on the road
@ALongLongWaytoGO
@ALongLongWaytoGO Год назад
Best thing I ever did to my Jeep…Josh at American Iron is a FANTASTIC dude…super helpful !!!!!….Over a year on them now….still the best thing ever.
@RockSolidRig
@RockSolidRig Год назад
We feel the same way!!
@motivatedcb5837
@motivatedcb5837 Год назад
I have just recently joined the Jeep world. I have been a truck guy my whole life but now due to current interests it makes more sense for me to own a Jeep. All this being said I have enjoyed going back to your old videos watching all your Jeep JK mods. Thank you for the entertainment and information.
@rvmagnum5415
@rvmagnum5415 Год назад
Your the first guy I have seen on youtube explain ball joint wear properly.
@wvjeepguy8178
@wvjeepguy8178 Год назад
Love mine. I've had a set in a Dana 44 for quite a while and getting ready to install a set in my dana 60.
@4WDTrek
@4WDTrek Год назад
Hey man. Just wanted to comment and say that your videos have developed super well over the years. I have been watching for some time now and happened across a video you made a long while back. Your comfort and ease on camera has come a long way and how you explain things is always amazing. I'm aspiring to have that progression in front of the camera my self on my channel! Thanks for all that you do bud!
@Arykperry
@Arykperry Год назад
I’ve had them for 2 an 1/2 years on my crawler now and love them !!!! There worth every penny !!
@trevorlynch6549
@trevorlynch6549 Год назад
The reason ball joints exist is for independent suspension where you have both types of movement and they discovered that they would work for solid axles and would be cheaper.
@dalephillips8250
@dalephillips8250 Год назад
So are you saying you can't do these deletes for Trucks that don't have a solid front axle?
@trevorlynch6549
@trevorlynch6549 Год назад
@@dalephillips8250 they make different kits than these but this style won't work on independent suspension.
@dalephillips8250
@dalephillips8250 Год назад
@@trevorlynch6549 Just wanted to know if this would be a viable option for a 2020 Tundra if my stock ball joints ever go out.
@trevorlynch6549
@trevorlynch6549 Год назад
@@dalephillips8250 There aren't any kits for newer tundras and I don't think it would be cost effective to get one for normal use. The ones that I found are over $1,000 for just the lower ball joint.
@dalephillips8250
@dalephillips8250 Год назад
@@trevorlynch6549 Thanks for the reply
@corymorgan1448
@corymorgan1448 Год назад
Had mine on my jk for about a year now. Josh is a first class guy and I love my deletes !
@daveayerstdavies
@daveayerstdavies Год назад
'Ball-joint deletes' are not without their own problems. The dynamic impact forces that might have been absorbed in the OEM ball joints will be transmitted to control arms, increasing load and wear. You don't completely erase the ball-joint problem, you move it to other suspension joints.
@lasagnajohn
@lasagnajohn 6 месяцев назад
Amen. AND, you don't know what other component is now the weakest link either. Jeep is already for wheeling, why mess with it? I guarantee you my stock XJ will go where you go, but then it will go back home too.
@fayceoff
@fayceoff 17 дней назад
Yes, but if you've already upgraded all of that stuff, it's much easier to replace bushings in control arms than replace ball joints in my opinion.
@TheRoadhammer379
@TheRoadhammer379 Год назад
Glad I found this video, I bought my BJE from down to Fab and he doesn't offer a BJE for both the upper and lower, only the upper. Thanks man.
@campNcrawlR
@campNcrawlR Год назад
Great video, brother, as always. Im at 40K and my balljoints are going, so this was timely. Something I’ve read about but hadn’t looked deep into them yet. You’ve convinced me and I look forward to hearing more about them next time 🤘🏼
@chancepierce
@chancepierce Год назад
Really looking forward to this one. I need new balljoints and have been considering the deletes but have not had time to do much research
@r.weaver3769
@r.weaver3769 Год назад
You are correct, I've seen countless RU-vid certified mocanics do that wiggle and say "It's bad. personally I jack up at the ball joint, and if I use a prybar and move the tire and see movement up and down or side to side, it's bad. now, GM use to say up to 1/4 inch up and down was acceptable, I sold them new ones anyway as it will wear tires, and eventually let loose. The old FORD kingpin I-beam suspension was my fav, was damn near bulletproof. but because the geniuses at Ford put the tie rods behind the steering axis they wandered at high speeds if set to spec, so I toed them in and requested the tires be rotated more often.
@StormbornJKU
@StormbornJKU Год назад
Don’t forget about the biggest pro of the deletes. You never have to press anything in or out ever again. They are rebuildable right inside the knuckle / C! And when I installed them on my JK44 I also had some wandering issues. Once I drove them for like 200 miles they were broken in and my steering feels absolutely amazing now. Better than it’s ever been!
@harrywalker968
@harrywalker968 Год назад
jeep, 1st thing you do, is re weld every brkt, or replace with thicker. jeep is like buying a body,,then fitting all the go stuff. swb f100 owner. perfect.
@StormbornJKU
@StormbornJKU Год назад
@@harrywalker968 cool man
@christopherparis6841
@christopherparis6841 Год назад
Yup lmao I bet the power steering returns like brand new lmfao. If ur blowing through ball joints how bout but a fkn axle meant for tires guys w Lil ds buy. Why not use Ford 9s or Dayna 90s or mouser 11.5s set of those retard pins cost as much as a used axel that's built for the purpose. Guys need to leave these pos jeeps to delivering mail. Lmao
@eugeneengland7282
@eugeneengland7282 Год назад
I was looking into those kits a couple months ago for my tj and wj. Thank you for this it makes my decision final.
@ToddAdams1234
@ToddAdams1234 Год назад
Did he say that a kit was made for the D44? I’m doing a solid axle swap for one into my 99 Taco. I don’t want to go to the cost of the D60, not to mention finding one from out of a vehicle with the proper width. I got my 44 from a first gen Bronco so the width is PERFECT. Now I’m in my the process of narrowing my D60 for the rear top have it match. What do you think?
@outinthebackyard7579
@outinthebackyard7579 Год назад
Just in case the average person doesn’t understand these ball joint delete kits only work in straight axle vehicles. On any vehicle with multi link suspension you absolutely need the multi directional movement of the ball and socket as the suspension travels.
@MrNigel1340
@MrNigel1340 Год назад
Have just found your channel and subscribed, marvellous presentation with clear and concise descriptions of how to fit the parts, thoroughly enjoyed it , regards Doc Cox.
@obiknobi8447
@obiknobi8447 Год назад
Thanks for sharing. This will save me a ton of time on my Nissan D21 build. Durable spares are non existent here in South Africa 🇿🇦. Cheers
@RocklanderUSA
@RocklanderUSA Год назад
You are awesome, Ben! I wish I could just bring my Jeep to you and have you install these ball joint deletes and lift. Great vid!
@Donnut123
@Donnut123 Год назад
I have had to do ball joints in almost every Jeep I've owned. I will be looking to install a set of these in my Jeep when I do joints!
@Pegcitytowing
@Pegcitytowing Год назад
I have them on my jeep since 2020, no issue they are great
@TX-oo2rn
@TX-oo2rn Год назад
Great video. Thanks for addressing the many questions I would have had by being very thorough. Cheers!
@jku392adventure
@jku392adventure Год назад
I love my ball joint deletes! They are doing great with my hemi!
@johncortese745
@johncortese745 Год назад
Love my American Iron Offroad Ball Joint Deletes for my SD60!!! Great customer service as well.
@relmdrifter
@relmdrifter Год назад
Thanks for the run down. I may start running these in my TJ and X
@michaelmurray2592
@michaelmurray2592 Год назад
Love the video Ben!!! I wouldn’t mind doing this swap on my JT. Keep up the great work my friend.
@gwkdad
@gwkdad Год назад
very timely, just started looking at these...
@AdventureAwaits4u
@AdventureAwaits4u Год назад
Great video and thanks for going in depth on the ball joint delete. 👍🏼
@javanbybee4822
@javanbybee4822 Год назад
I’m a fan of the bolt on ball joints on IFS Toyotas. Super tough and easy to replace.
@cowboytr25
@cowboytr25 Год назад
My next set of ball joints will be the ball joint deletes. Great video thanks. I like that you were straight forward about how it felt on the road.
@cubs11992
@cubs11992 Год назад
This is new to me , never heard of this 🤯 thanks I might do this
@millstonejeepworx
@millstonejeepworx Год назад
Awesome Ben, Was considering these for mine.
@d7k8gsxr600
@d7k8gsxr600 Год назад
Hey.... that first photo looks familiar! 🤔 lol.... American Iron BJE are awesome. Josh is a great guy to buy from amd his product is spot on. After I had that catastrophic failure I knew these were the ticket. So far the drive great and having the 1.5° adjustment makes it drive great on the road. I also installed the 1550 shafts, but I didn't have to trim the upper bolt.
@1607rosie
@1607rosie Год назад
Pretty cool set up!
@zachredline
@zachredline 3 месяца назад
Not sure if anyone mentioned it already, but you don't need a 19mm Allen key if you don't already have one. Any high strength bolt that uses a 19mm socket will fit. You just need to add a nut or 2 for the socket or wrench to fit onto. Had to do that on my nv3500 Trans overhaul.
@DaveyBlue32
@DaveyBlue32 Год назад
Those look awesome! Great stuff!
@tooxlent
@tooxlent Год назад
Great video, keep up the content.
@TheTurbogixxer
@TheTurbogixxer 6 месяцев назад
Thank you for all your video content, is there any way you can do an update on the reliability of these ball joint deletes?
@TheSleepingonit
@TheSleepingonit Год назад
I have to put a pulley on my replacement power steering pump. I got the pulley puller kit, are the adapters that go on the bolts that go into the shaft deliberately too big for the bolts? I just found you and subscribed
@adidas4275
@adidas4275 Год назад
Can you explain how these are different than the dynatrac ball joints which also use a spherical bearing vs a ball & cup?
@jt4211
@jt4211 Год назад
That stiffness should loosen up. The same happened when I put in new synergy balljoints. It was pretty squirrelly at first but loosened up after a few 100 miles. I’m planning to do deletes when upgrading the axle. Thanks for the vid.
@logicalguy488
@logicalguy488 Год назад
Good job, but just a tip for you when you tightening a nut and bolt or torquing a nut and bolt, always try and hold the bolt and torque or tighten the nut. The nut tightens more like a jam nut giving you a much better lock.
@JEEPIMPACT
@JEEPIMPACT Год назад
Wholly Molly, I've missed a lot of videos. RU-vid isn't doing a good job on the notifications 🙄. Good video thanks 👍
@XxAvengr
@XxAvengr 13 дней назад
What kind of sidesteps do you got on that jeep? Great video by the way!
@David-yy7lb
@David-yy7lb Год назад
That's awesome....I did a solid axle swap on my 08 duramax however I used a super dana 60 that came out of a 2018 f350 super duty with 1550 steering u-joints and I would love to use those ball joint deletes what part number for those ball joints for that ford front axle I have
@ODGColornChrome
@ODGColornChrome Год назад
Awesome I wish they had something like that for A arms.
@chrislorenz4468
@chrislorenz4468 Год назад
I purchased the barn's tie rod upgrade for my JK from watching your channel and I plan on purchasing these ball join deletes in the near future one question I hope you can answer what is your recommended caster tippinion angle I couldn't find the video that you did once for a stock JK Rubicon axle 4" lift getting vibration and I know my pinion angle is off trying to get her dialed in first alinment shop wasted my money going to another soon if you could give your oh pinion lol thanks for great videos!!
@JeepinBailey
@JeepinBailey Год назад
Any plans to add these to the JT? I could use an upgrade and Considering these for my JL.
@scottc3165
@scottc3165 Год назад
Very nice. I wish I had a nice shop (with a/c!). But I need to do this on 1st Gen 4runner.
@Kevinrowland-dz2ut
@Kevinrowland-dz2ut 10 месяцев назад
very well explained- your a pro.
@Davidtheinfidel
@Davidtheinfidel Год назад
I love them. Will never go back to regular ball joints
@simisonicblack
@simisonicblack Год назад
The X-mas tree lights on your dash makes me cringe lol 😂
@billchessell8213
@billchessell8213 7 месяцев назад
Well done!
@Nanan00
@Nanan00 Год назад
Dude get a MRCOOL 24k or 32k mini-split for the garage, I put AC in my garage earlier this summer and it makes life so much better not sweating to death in this humid golf coast Texas heat while working on my YJ. I just picked up a 2012 F350 superduty Dana 60 and a 2002 Tahoe 10.5" 14 Bolt rear axle for my build, I had been thinking about doing the ball joint eliminators when I get to that point but first, re-gear and lockers!
@therightarmofthefreeworld4579
Thanks, I have 2 F250 hiboys; ‘76 & ‘77. This will definitely help the loaded drive ability on the interstate 👍
@TheRoadhammer379
@TheRoadhammer379 Год назад
Hey bud, do you have a Dana 60 or 44? my 77 F250 crew had kingpins
@TheRoadhammer379
@TheRoadhammer379 Год назад
Only available for 92 and newer dana 60
@guthrey51
@guthrey51 Год назад
Thank you, I was already shopping between these, tera, rare, and dyna after my set of "heavy duty lol" ball joints already feel dead in 20k miles. I didnt really understand how they were different than a standard balljoint until you had them apart and explained.
@hardwickchris1
@hardwickchris1 10 месяцев назад
Yeah, they are all trash. I'm only running 35's ... I spent over $550 for TeraFlex "ADJUSTABLE / LIFETIME" Ball Joint kit... GOOD LUCK GETTING TERAFLEX TECHNICAL SUPPORT FOR WHY TERAFLEX KIT CAN NOT BE ADJUSTED...
@ethangonzales3000
@ethangonzales3000 8 месяцев назад
@@hardwickchris1what ball joints do you recommend?
@johnnylightning5633
@johnnylightning5633 Год назад
Do those need to get any type of greasing and in the Northern areas would salt etc be a problem?
@n.b.p.davenport7066
@n.b.p.davenport7066 Год назад
Thumbs up on the video, excellent , right to the point
@SincerelyLate
@SincerelyLate Год назад
Can you do this for pickups also? Or just for Jeep models
@ELEVENSDIRTLIFE
@ELEVENSDIRTLIFE Год назад
Great vid. I’ve been going back and forth on whether or not to switch to deletes. This vid pushed me over to making the switch. On another note, what two post lift do you have? Do you like it? I’m looking at putting one in my shop but fact finding on which one to go with.
@JKGearandGadgets
@JKGearandGadgets Год назад
It’s the forward I10. I like it, honestly I didn’t shop around too much, it was a great wholesale closeout deal at a local lift distributor here in OKC. It does have a little wiggle compared to others I’ve used in the past, but it does everything I want
@ELEVENSDIRTLIFE
@ELEVENSDIRTLIFE Год назад
@@JKGearandGadgets awesome. Thanks, I’ll check it out
@clintdavis9717
@clintdavis9717 Год назад
Ball joint delete are a sweet mod. But I have to ask Ben where did you get those front turn signals?
@barrycriswell8967
@barrycriswell8967 Год назад
Like to see tj vid with ! Im using green /sleeve loctite to hold uppers in
@jasonbogdovitz7357
@jasonbogdovitz7357 Год назад
I’m must be refreshing driving down the road with every possible dash light on lol
@leanderpruett4924
@leanderpruett4924 Год назад
I just went to rcv axles I wonder if these would fit??
@BobNob1
@BobNob1 Год назад
can you make a video of the jeep flexing does the tire go on an angle?
@rkuehner1012
@rkuehner1012 Год назад
Looking at the front of your jeep...I thought you installed a Motobilt Hatchet bumper on the front? Did you not like it?
@niz308
@niz308 Год назад
36c just another day in Oz hahaha great vid man
@mazevx2451
@mazevx2451 Год назад
I already had contacted American Iron a while ago but still debating if I should invest in the stock axle, shipping and tax add quite a bit to the price.
@methanial73
@methanial73 Год назад
I don't see any zert fittings on it. Do you have to rebuild if often? That's my only complaint.
@rrvallance
@rrvallance Год назад
Great video.
@PowerWash2022
@PowerWash2022 Год назад
I wonder if they sell these for different vehicles cause I'm tired of replacing ball joints every yr.
@mattbarrett41
@mattbarrett41 Год назад
I have an F-350 with Dana 60’s. Will these work?
@run2thefight
@run2thefight Год назад
I just did upper and lowers on my XJ and it was a nightmare since I had to long arm crank them in and the press I rented didn’t have the “exact” size press cup to force it in straight. These would be a great alternative since they don’t have the joint leg sticking out to consider when pressing
@loveisallweneedify
@loveisallweneedify 5 месяцев назад
hello, i just put mines on my jk Wrangler 2018, and my ABS is on but i know its one of my sensors went bad when taken it out, so I also had to do an alignment , but the ABS Light is still on hahah , any advise ? and what is the news on theses babies?
@oaktreejw
@oaktreejw Год назад
I would certainly hope that brand new ball joints or in this case delete’s would be super responsive especially after replacing WORN parts
@michelletennant9164
@michelletennant9164 Год назад
Would you do this on the jl or jt?
@richardxstroker
@richardxstroker 5 месяцев назад
After a level and 35’s on my Ram, this will probably be my next purchase. Never done ball joints after 105k miles now, but I know it’s time, and I don’t want to be replacing them again.
@eric4847
@eric4847 Год назад
Do they have these kits for the factory 04 axle assembly?
@alphasquatch6967
@alphasquatch6967 22 дня назад
Do they cause extra noise saw a few reviews that claimed this. My only concern is that..
@BunnyTJ
@BunnyTJ Год назад
Looks like an awesome upgrade! what about on the Gladiator? Or is this only for heavy offroading?
@JKGearandGadgets
@JKGearandGadgets Год назад
Great upgrade for a jl/jt
@Golgi-Gyges
@Golgi-Gyges Год назад
Active Duty Training? Are you in the Guard?
@stevek9844
@stevek9844 Год назад
Do they make a replacement for the joint on the pittman arm?
@FirstGendodgegarage
@FirstGendodgegarage Год назад
Will these work on dana44 dodge
@jgc0064
@jgc0064 Год назад
Maybe the additional caster had something to do with the steering feel as well? Obviously the 3 link needs some love too.
@sferg9582
@sferg9582 Год назад
Hint: When it gets that hot in your shop, turn off the ceiling fans. Keep the heat up and away and not blowing down on you. Ceiling fans are great in the winter, but not so much in the heat.
@jeffmoore695
@jeffmoore695 Год назад
Need a set for my TJ. Can't afford them right. Maybe next year.
@n.b.p.davenport7066
@n.b.p.davenport7066 Год назад
They don't make those for most all other vehicles? Looks like fantastic idea!
@nobodynoone2500
@nobodynoone2500 29 дней назад
Ball joints are for articulation. Everything flexes, especially on the trail. You are just moving the failure point to somewhere more expensive and difficult to replace and possibly introducing bind.
@JKGearandGadgets
@JKGearandGadgets 29 дней назад
Please explain how balljoints articulate on a solid axle lol…. Very incorrect comment
@JKGearandGadgets
@JKGearandGadgets 29 дней назад
How do kingpins work then? The only time a balljoint will articulate is on an IFS axle.
@lloydprunier4415
@lloydprunier4415 Год назад
Are the bearings sealed or can they be greased?
@scottdowney4318
@scottdowney4318 Год назад
Same idea is used if you want to straighten steel rod. Heat the side opposite the bend.. When it cools, it shrinks and pulls it straight. Just spot heat to red, dont heat any other places.
@1967250s
@1967250s Год назад
Interesting improvement. How come they don't come with boots and grease nipples if they are used for off roaring? Even for on road, having them sealed up against the elements would be an improvement.
@LFTDoffroad
@LFTDoffroad Год назад
What, no grease or oil in those joints? that's cool. thanks for the video.
@americanrambler4972
@americanrambler4972 Год назад
Other than the alignment collar, this looks almost exactly like the kingpins on pops old 1969 F-100 Twin I Beam pickup. It. Used bushings instead of your expensive hiem joint setup.
@mackneal3246
@mackneal3246 2 месяца назад
I have hear that American iron ball joint deletes are noisy. Can you confirm or deny that after 1 year of use?
@oldelibertystructures5401
@oldelibertystructures5401 3 дня назад
Do they make them for Power Wagons?
@patricklaughrey8727
@patricklaughrey8727 Год назад
Do the balljoint deletes eliminate the dreaded death wobble??
@anthonyshattuck5917
@anthonyshattuck5917 Год назад
My 71 Chevrolet 1/2 ton 4×4 is getting some of those.
@TheRoadhammer379
@TheRoadhammer379 Год назад
they don't offer these for any chevy, and especially half ton axles
@DigClams
@DigClams 11 месяцев назад
So I'm new to doing mods/upgrades on my 2012 JKU Sahara. Would these ball joint deletes work on my vehicle as well? I have been looking at new to me (2021'ish) Rubicons but not willing to pay the price that the dealers are charging so going to do mods instead.
@JKGearandGadgets
@JKGearandGadgets 11 месяцев назад
Yes they have a Jk specific balljoint delete
Далее
TeraFlex Install: JK HD Replacement Ball Joint
15:36
Просмотров 194 тыс.
ТЕСТИРУЮ БЛЕСКИ RHODE 💕✨ #shorts
00:30
STOP Dry Starting your Pentastar 3.6!!
13:18
Просмотров 384 тыс.
We're NEVER DOING THIS AGAIN!
13:11
Просмотров 3,5 тыс.
These NEW Harbor Freight Lights are INSANE!
20:42
Просмотров 194 тыс.
Amazing Diesel Motorcycle 🔥
0:19
Просмотров 30 млн