If you are not a Plumber, you should watch this video! Tricks installing stop valves for Pvc Pipes 

How to install stop valve on pvc pipes as shown in the video will make the process of replacement or repair later easy and flexible! How do you see the idea of ​​installing the valve on this pvc pipes ? Please leave your thoughts in this comment section! Thanks for watching !

Correct idea but costly. Single Union can be sufficient

nice. The advantage of this method is when it comes to change the ball valve..it makes it easier 👍

Here in the US, if I was concerned about easy valve replacement, I would just use a Sharkbite valve. Otherwise, if replacement was necessary, I would just cut out a section of pipe and use cemented PVC couplers to connect a short stub on either side.

That is the way I assembled my 160' deep well pipe, sans valve, but with couplers between each 20' section of pipe. Continuous poly is usually used but pulling the pump was a lot easier with the couplers when you don't have a crane and winch. Your technique (with one coupler as noted below) is a useful approach to replacing or adding a valve.

I am a plumber and still watch this video ❤

I'm Electronic and Electri Service Engineer . But ❓ I Like The Plumbing Work. Some Time I Fittings Water Pumps Plumber Works. Today I Got New Ideas. Once Again Thank You For Sharing..

I've been brainstorming how to install a 1 inch ball valve into a gravity fed pvc line from my spring fed water tank where it enters the house upstream from my water filter. No flex in the pipe so your suggestion is perfect! Plus, the valve is serviceable in the future without cutting remaining pvc again and again. Thanks!

Very informative video. I learned a lot from this one, and the plumber never said a word. His work did the talking. My hat's off to you sir.

You only need one disconnect coupling, this is because once the coupling is un-threaded, the valve can simple turn to spin off the male connection on the other side.

I have had on my mind to install a shut off valve in the 3/4" PVC water line coming into my house for sometime now. This video is exactly what I needed to see to get my valve installed. Will get the parts today. Thank you very much for this video.

Nice idea, you can easily change the valve once broken.

Same problem happened in my house...I searched for changing the gate valve....thankyou very much

Appreciate💕 both you and your Shares Thank you

Very convenient for disassembly

Thank you for showing this and very idea 💡 you r the best

1. Only PVC valve (both end female socket type) will be just sufficient to replace. 2. At last you installed the valve diametrically opposite to that you saw in starting of video for correct direction of its lever. 3. Anyway, it is a nice video. 🎉

Simple and useful tips

What a good idea to apply for...Thanks.

thanks for the sharing. it's very necessary for me

Plumbing just got a whole lot fancier with this valve installation! 💧🎩

Thanks for your Idea WE can need that one day

Now u have 2 find where they sell it and name of it. Also 2 much thread tape can easily cross thread it when screwing on.

Excellent method onday a client asked the same question. How to connect ball valve?

You deserve a hug right now

Thanks! Makes it easy, practicable & safe as well as caters for future maintenance if need 👍

That's doing it the hard way. Also unless the pvc is schedule 80, the pipe is for electrical work and not code approved for plumbing. Maybe things have changed since I retired after 45 years as a plumbing contractor.

Breathtaking 💖💖

Very good cogragulation.

Thank you very much

why have 2 unions when you only need 1? better yet: 1) use a sharkbite shut off (the 2 unions will more than pay for it). or with the shutoff (threaded) shown 2) use a single sharkbite straight connect. 3) sharkbite Quick Connect Push to Connect/John Guest Speedfit Union fitting (these are made out of pex). If its its outdoor or irrigation, use an orbit PVC-Lock fitting (push on). All of these will be cheaper and easier than 2 unions and all will allow shut off to be removed if it fails.

Thank you

very creative and it worked for me

Buen video.Gracias por compartir.👍🙋🇪🇦

Muito interessante a técnica. 😊

Excellent 👌

Muito bom.....RJ,vou fazer

Hoy aprendí contigo 😮

I will try with these tips

good tips. very creative

Overkill...no thanks..

great idea. I'm planing to install a temporary water line source and want to redesign it after finishing some renovation and this idea really help although its costly but its really efficient rather than cutting and buying new pipe and fittings and this video really fits for low pressure water lines

Just magnificent 🌹🌹

Very good ❤

OMG😍,Awww💞 I love this

great connection

THANK YOU VERY GOOD AND FUN VIDEO!

Good for you

Outstanding

Enjoyed the finger pointing.

😍great🔥🔥 It's engaging!❤️

The purpose of using union in this TUT in next changing of stop valve you won't cut a piece of pipe. Nice idea.

2 things u forgot . when u cut the pipe u have to deburr it. And second thing u have to clean it with a PVC Cleaner before u get the glue on. These are two very important things.

Wonderful💮

Using conduit for water pipe looks like problem number one.

thank you for sharing😮

Молодец,👍

Excellent

good job bro, keep it up

Good tricks for life

Dude just cut it and glue it plenty of flex on that pipe

Good information sir

This guy seems to know what he's doing, so well done. Very educating video. Generally the problem with plumbers is that if you ask 10 of them how to solve plumbing problem X, they'll come back with 11 different solutions and then they'll start arguing with each other that everyone else is an imbecile and a fraud.

The usual problem here is when the teflon you put on both ends of the valve turned out to be insufficient. You turn on the water, and the teflon starts leaking. But you glued both ends already, so you have to repeat the process all over again and buy another set of fittings.

Wonderful shot

great job

spectacular ocean until you're officially captivate me...great

Mantaf tq for infornation👍👍

Hay lắm ak.nhớ ra nhiều video nữa nhé

Good lesson tanks

i love you your idea

Such small pipe is flexible. IF you have enough length, you don't need a treaded coupler

They sell the pvc valve with the unions already on them, much cheaper and less chance of leaks since no threads with teflon tape are used. and they are much shorter than what you put together. If for some reason you can't find the unions and need to fix a problem right away, a valve and 4 90's will work. glue the 90's on the valve and see how much you need to cut from the pipe with the other 2 90's on the pipe. Yes it will not be straight inline as before, so it might not work in some cases, but for most, it will.

I would leave at least a couple of inches between the union and the fitting attached to the valve, for more flexibility in case future work is needed. Just one union would be enough for this job.

Pvc pipe very easy to install safety valve without union specially smaller pipe

Все сделано классно но есть один вопрос какой клей использовали

Don't forget to chamfer the pipe ends, that way the PVC cement doesn't get pushed out and you get a proper chemical weld. Using primer would be best too. Not saying that what you did won't last for years, but for just a little more effort, you could have much stronger joints. This matters even more for elbows. TLDR; follow the instructions on the can of PVC cement exactly for the strongest, longest lasting joints.

If no union ive dremmeled out stop and used coupling

Good job sir

Excelente. Míster. Pero con una tuerca unión es suficiente.

Super

hey I wanted to ask if we can use " metal repair paste" on blue pvc pipe water??

Wooow... very very amazing

Nice idea bro.

In New Zealand the valve can be clamped onto the pipe with an adaptor and a clamping tool. No glue required and the clamping requires only 3 seconds. The clamp connection is stronger than the plastic pipe.

❤ it's just amazing you are sharing your plumbing skills to assist people who never ever done any plumbing work which is really appreciated, sorry 4 some of the negative feedback in the comments section,have a great day

What's the point of unions if you going to put them that close to adapters

Or buy one pvc union valve. I would definitely suggest to use pipe dope on pvc male going into brass if you go the route you did

great video bro

Nice

Beautiful Videos 🍧

Most expensive valve installation ever!!! Why not just the valve???all you would need is one sch80 socket ball valve!!!

Who makes the cutting tool you have

Colocando solo un enlace de tres piezas ya es suficiente, no se necesita colocar los dos enlaces de tres piezas para poder desmontar la válvula cuando surja algún problema que no ocasione el tener que substituirla. Gracias.

Super buenas ideas

Mantap...sangat bermanfaat.....

ممتاز جدا جدا شكرا لك يا بطل

People talking about adding two leak weak spots, big deal, if happens, just install new o rings.. Nice video Sir.

You can only use one coupling two is not advisable

Place union(s) to replace valve when broken.