Install the Creality Ender 3 S1 High Flow Kit for Sonic Pad with 5015 Fan and V3 Air Duct by ZUFF 

Very welcome! Stick around

Same here. Thank you.

🙏🏼🙏🏼🙏🏼

I am not a fan of the S1. It SHOULD be super, but for whatever reason, mine was a pain in the ass. Careful with "Upgrades". What is yours doing?

@3DRundown Driving itself into the print plate until I updated the firmware. Then that bricked it (the red-light and screaming). Then, I installed the professional firmware. Which seems to have resurrected it. Now I'm having issues with consistent temperatures, the prints not sticking to the print plate, but the strip that prints before the print to clear the print nozzle prints perfectly and sticks. I replaced the nozzles with - I think they were carbide? I tried to pull them back up on the creality page, but I can't find them. But they were supposed to be both crush and heat resistant. I have on order: a replacement magnetic plate, because the current one was ruined and is missing chunks. Also, the glass one. Because the magnetic one has me at my wits end. A replacement auto leveling sensor (because I thought that might be the reason for the sudden dive into the print plate?) And the ceramic heating piece for the sprite Extruder (because of the sudden inability to maintain temperature stability. It looks like its plug and play, so it should be an easy part swap. But knowing creality, I'll end up screaming profanities.) Right now, I'm watching your bed leveling video and doing that.

Your Z Offset is causing the nozzle to hit the bed. When replacing firmware, you will need to set the Z Offset again. Use the glass. It is best. Use MRISCOC firmware I have not test the ceramic hit end, but the Speedy Spider Hot end uses it, and I hat troubles with it. Maybe this one will be ok. The problem is likely the thermistor, or heater tube. Or, you need to run a PID tune.

@3DRundown Good to know! I planned on tuning it while swapping out the bed. Just do it all at once. Do any of the parts require greasing or lightweight oil lubrication? And when you replace the thermistor, the paste used, is that just standard thermal paste?

Don't go crazy on parts. Do what you need 1st, and of course, the Glass bed. No oils oils or grease. Only PTFE like this: Though, I almost never have used it on anything.... amzn.to/3OJypmt There are mixed opinions, but, a little Thermal Paste, similar to CPU Thermal Paste will work.

Thanks so much!! I try to teach the way I want to be taught. Slowly and Completely. 🤜🏼🤛🏼

😂😂

I tried dozens of times, and even spoke to Creality about it. They told me only resellers can make the account. If it's working now, things have changed. However, I wouldn't use that stl.

I'm not sure why they keep this so under the radar. It's a solid kit

Hope it's fixed up now

@3DRundown - Sorry for late reply. At the end, I ordered new PCB. Works fine now. Installed it another way for second time - pluged hotend cable first and then moved whole PCB into place. Seems making little bit smaller tension - connector is OK now.

Looks like the kit isn't linked.... Used to be for sure. I'll check tmr (monday)

According to Creality, it is not possible to make an account. I tried for about 2 weeks. They told me the site is only for re-sellers. They eventually sent me an stl, but it's wrong. Doesn't work at all. How did you manage to get this, and does the file fit? I was told by others, that the file is actually a users file that they took and provided without permission.

Thank you brother!!

Welcome!

I keep it all on the default 0.2 profile fan settings

I only have a quick min, but didn't want to leave you waiting.. so, quickt: 1.) The fan is reasonably quiet. 2.) they are proprietary, so cost more, and less options, but not really THAT big a deal. The Speedy Spider, went back to using MK8. That is the way they shoulda went. That said, the Nozzles are good nozzles. Not a single clog yet. 3.) No. unless you want to try pushing it for more speed 4.) Because the Zuff Shroud is not compatible with the Metal one

It works. That's exactly why. 😜 They do work, and since we're not using a ton of torque on these little screws. There really isn't much worry about stripping. Also, get the new Speedy Spider! They corrected the Nozzle situation

Should be a link in the video description

Very welcome! Can't thank you enough, for the Super Thanks. Means allot, and helps me keep going! :)

Thanks so much, will do!!

Have I helped you? Help ME continue this channel with some support: TIP: Click the "💗THANKS" button Become a RU-vid Member, by clicking "JOIN" Support my Patreon: patreon.com/3drundown Use my Affiliate Links when Shopping: Amazon Link: amzn.to/2miGQq9 Creality: shrsl.com/424l2 Bambu Lab: shrsl.com/46lky Sunlu: sovol3d.com?sca_ref=2756755.r8WNQiJdNf Sovol: www.sunlu.com?sca_ref=4022320.F0sV6y4ht9 Support me via my Course: 3DRUNDOWN.COM

The 4 was actually out when I did the 3, but I liked the 3 Better. My S1 sucks. I don't even have it hooked up, but I'll see if I can do the V4

Use the smallest spacer that works. The ones that come with the kit should be fine. In the retracted position, the probe needs to be above the Nozzle.

The Nozzle in the kit IS a Spider Nozzle

Yes, I used PET-G

Nah, just add the spacer and you're good.

I think it was JST micro IIRC. Look into the S1 "modder board" which has standard JST fan connections on it.

I never bothered to do it. Shroud options are a pain. Better off using a spider 3 or speedy

They come with the kit, or, make your own: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-fhTIfO1m_yQ.htmlsi=wiktFmKr4OD4TYI7

Yes and no. If you can get the creality fan, I would go with that. Then print the Zuff. If not, you can get another 5015 and splice the connector yourself. I am not in love with being restricted to the spider 1 Nozzles

Yes

@@3DRundowndo you have a link for the one you bought?

Yup. I have a few on the way. Can't wait. The Spider 3 has been kicking ass on my Ender 3 Max. Best hot end they ever made by far. Creality? Support? Lolz

@@3DRundown can you tell me where i can find the speedy spider for ender 3s1 ?

Sadly, I haven't been able to find it.

No, cause you'll have a big unused hole where the fan blower goes

Thanks so much @@3DRundown then I'm really big trouble now :) My Hotend Thermistor for the old Hotend broke and I can't print anymore. Because of bad delivery times and my Sonic Pad, I ordered this new High-Flow Kit. So I guess I will not be able to print the bracket :)

Always have a backup printer. Grab something used on ebay. Whatever it takes. Have a second machine

btw: a really really enjoy your videos and admire your work! @@3DRundown

Thanks so much. Good to have you!

Weird. That stinks

@@3DRundown cheap fix though!

indeed

Thanks

Forgive me, it's spider nozzles, like this: Micro Swiss Spider Nozzle 0.4: amzn.to/3mfwJoX Micro Swiss Spider Nozzle 0.6: amzn.to/3KG9fDz

Make sure on correct shop. Go to creality.com and click "store", type in High flow kit.

Been having the same problem. Can only find the high flow kit for the Ender 3 V2

@@hleumasg at the moment unfortunately it is only available in the US store

This has got to be somekind of wiring situation. I would consider replacing the Thermistor or heater tube

@@3DRundown thanks for the pointer. I guess how’s a good time to trap the high flow kit. Been contemplating it since I watched your video on it.

Changed my retraction from 1mm to 3mm and increased retraction speed and print speed a little and it worked itself out.

Oh? Where's that usually?

So, you didn't actually watch the video?

I show the set screw, twice, in the video

When it's lowering, if you trigger the probe, does it stop? Sounds like make CR-Touch is too low. Did you install the spacers? They look like little metal tubes. Or, Try this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-fhTIfO1m_yQ.html

​@@3DRundown You are absolutely right! I found it later on that I overlooked spacers to probe. Shame on me. Thank you! BTW: is there any way how to configure fan speed, it resets value to zero during new printing. It's annoying to keep it in my mind. Thank you for advice. I wish you a lot of great videos like that on RU-vid!

Your GCODE will turn the fan on and off as needed, as well as set the speed. It's all done in the slicer.

Yup. Firmware is up to you. Many choices. I use MRISCOC

You can, but I had no need

BOTH. It will add a larger throat, and HF Nozzle. But it's a bigger upgrade for the S1, and S1+, as they don't have allmetal

@@3DRundown after much research I found it has a copper throat

Yep

I think you'd be ok with PLA. Print 2. When/if one warps, swap it.

@@3DRundown Oh yeah, haha of course!

You may indeed want to do some calibrating. For me. A small retraction change was all I needed. Can run some Calibration towers. Temp, speed, retractions. See how things look

Yea, seams only the Creality fan has the correct connection. I'm not sure what the right one is. I'd have to google some. Can splice it to the creality wire

They are Picoblade 1.25mm jst connectors..amazon has them in kit form.

Cheap out? You Drunk. Creality may make occasional missteps, but they usually resolve them and certainly never "Cheap Out". They are the best China company I work with by FAR. And I work with ALLOT of china companies. Very hard working, always innovating. Fix their mistakes. Friendly and active in the community.

It's in the description

Yesssir

@@3DRundown do I need to use as many as you did?

I would use the little metal ones that came with the kit, they will be the perfect length.

I'll do it. Make me an offer and let's get it done

@@3DRundownlet me know what the parts etc cost would be and what you think your estimated time would be worth for you?

@@3DRundown whats the best way to contact you?

Insta, FB, Etsy, Email, ebay.... Take your pic... UDEMY, PATREON... ;)

I honestly don't push speed much at all. As printing is my full time business, I focus solely on Success, and Quality. I'm usually anywhere between 30-60, with 45ish being most common. This is on the low end.... But, this hot end has been great so far.

I'm using klipper and the sprite extruder pro kit, and I can print ABS to 200mm/s without any problems. 200mm/s has a flow of 16mm³/s, so the hotend can handle it well.

​@@ledzpg do you have a ender 3 s1 ?

Because PETG can handle higher temp, and is stronger. Mainly for the higher temps, so it won't warp.

@@3DRundownhave you found petg to continue to hold up? I’ve always used abs for parts near the extruder and heat plate for the added temp resistance but nice to know that petg as an option if it continues to hold up

No. You can use the new Ceramic Hot End, on the Sprite

Less so, but YES.

It should be a .4 installed. I think.....maybe.

@@3DRundown thanks hope your right the extra nozzle is .6

Just printed and installed the duct fan V4 and checked it is indeed a .04 installed.

This Spider hot end is quite a bit heavier than stock, has anyone tried the ceramic hot end for the Sprite? It’s much lighter.

Spider isn't for the Sprite, but the HF Kit uses the Spider heater block and Nozzle. Speedy Spider is Ceramic. Heats crazy fast. The Sprite Ceramic should as well

This shroud has been updated since here, and there is a new version, but I prefer this one still. Welcome

@@3DRundown ok many thanks for fast reply.. Im juat watching through your vids... And i'll take look at booth Thanks

They are Similar, but not meant to be compatible. They have different thread lengths.

@@3DRundownso what would you say to use with this? Because I’ve seen many people saying using the MK8 nozzles will ooze out filament? Just don’t want a big mess on my hands! And want to get some clean prints!

Micro Swiss Spider Nozzle 0.4: amzn.to/3mfwJoX Micro Swiss Spider Nozzle 0.6: amzn.to/3KG9fDz

5015 included in the kit

Creality are the most helpful, interactive, and friendly, 3D printer company by FAR. Their support is great. So great, I've become personal friends with many people at Creality.

@@3DRundown good to know. i WILL take your word for it. maybe i misunderstood, I meant instructions. but reason i said that is cuz they provided the fan, with no solution for mounting. then when you opened the instructions, that link. Then the whole situation with the incorrect file that doesnt work. So you had to go thru "community support" to find the fan duct. And then....the design (in their instruction booklet) being somebody elses. BUT, i realize thats just the instruction booklet and isnt necessarily reflective of their support people. my ender 3 s1 instructions were goofy in a few spots too. but i have done tech support before, and I know the pain, ;D, of having to be the support person, for a product that has an obscurity in the manual. As people will tend to hate on you (as if you wrote the manual yourself!) 😑 much respect to any support team that is worth mentioning because good tech support these days is harder and harder to find. most people outsource to india/manilla/etc....that sounds like a line, but im in IT support, so Im constantly calling many different manufacturers for stuff. I do appreciate support that will take the time to listen to you, and shows actual empathy, or tries. I am however convinced that the worst support on the face of the planet lies in: Hewlett Packard. Pray you dont ever have the displeasure of experiencing their tech support. Sorry Creality for crapping on your name, love you guys!

Oh man. Yea... The Duct fan was not ideal, and I was not pleased about that. I also couldn't get the "VIP" site, to work, where the duct was for download. The good news is, in the past year or so, Creality has done a LOT of course correcting. Manuals are better, support is better, the VIP site works.... But yea, Creality are really great peeps. I like them allot.

I think he might mean the thread length, it’s not usual and a bit longer than standard nozzles. But i‘m not 100 percent sure.

It's the "Spider Nozzle", you'll need to use that one. So far, It's working well, but they are a little pricey and less available than more standard V6 or MK8 nozzles

Yea, it's the Spider Nozzle. An uncommon size

I haven't got my hands on the new fan kit, but it likely crushes the 5015. That said, i've had no cooling issues at all

I used the S1's thermistor. They look super similar to me...

Its a NTC100K-3950 if it still matters. 15x3 Cartridge style.

More so for the S1 and S1 Plus, but you'll still get a better heat break, HF Nozzle, and much better cooling.

You said you have a class? Im wanting to learn more about printing. Setting/adjusting speeds, temp, walls. Etc.

Somebody Jelly? Somebody Jelly.... #CryMore

😂only a complete sissy would leave a comment like this. What an absolute sissy nerd.

Not as much as the S1 or S1+, as it's already all metal, but the throat and Nozzle are physically larger, so, while less so, it's a yes.

I don't watch any other influencers, but, I can tell you from my personal experience, that Creality has never asked, nor even HINTED, at leaving them a favorable review. I had an 80 minute Video chat with several people from Creality last week, and even then, nobody even so much as WINKED at me, for a favorable review. They simply ask me if I'm interested in an item. If I say yes, they give me a time frame on sending it, and that's that. They never ever guide me in any way, on how to cover the item. That said, I can only speak on my own experiences. Creality has some weakness, but, other 3D printers have the same, and most of them, deal with a much smaller user base than Creality. The industry as a whole, has much room for improvement, when it comes to support, and documentation

People print twice that speed on S1's.

i dont have to save 30 or 60 min time.@@3DRundown

Some people print things that take 3-4 days. You'd be saving hours. But, who really cares? You do you...

How to Resize, print & install a CR TOUCH or BL TOUCH SPACER for any 3D Printer, in Cura ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-fhTIfO1m_yQ.html

I thought about linking you to something else. 😆😆😆

This kit is easy to install and works great.

Yep. That's how teaching works. You turned a pleasant video into a depository for your Mouth Vomit. I win. Bye

@@3DRundowndude, why are these comments full of absolutely annoying douche bags?

Because HUMANS, in General, are annoying Douche Bags

Creality has several Customer support channels, and communicate with people everyday. I've never had trouble reachine them. Now, try to get a reply from BAMBU.

@@3DRundown I tried via Facebook messenger and never got a reply from them. Via email I did get replies but man were they slow. I'm not aware of any other channels but if you have any pointers i'll gladly take them.

They have a FB page for Support, and they also have live support on CREALITY.COM. You need to try on THEIR time, so, after 9pm EST is best. Sometimes they aren't knowledgeable enough, but, higher ups review the chat and follow up with emails.

My channel made $1800 in October L🤡L