Тёмный

Install TIMING CHAIN & VALVE COVER - 160tkm service PART 5 - BMW F20 engine N13 

At Home Vlog - by Jani Voutilainen
Подписаться 8 тыс.
Просмотров 71 тыс.
50% 1

You may WANT to do 160,000 km of service for your BMW - [PART 5]
#BMWF20 #TIMINGCHAIN #VALVECOVER #CHAINTENSIONER #OILSERVICE #COOLANTBLEED
Are you buying a BMW car with over 160000 km or 100000 miles?
As in the previous episodes, I do a 160 tkm service for my BMW F20 car
Diagnosis & maintenance BMW F20 116 2013 engine N13 (N13B16)
00:00 Intro
00:14 How about old timing chain and compare with new one
- Remove chain from guide rails
- Let’s take a closer look at the condition and compare
- how much the old chain has stretched
- The guide rail has cracked at one point
- Guide rails connection point is really loose
- Chain sprocket
- Compare the old chain vs. new chain
- The timing chain and guide rails back together
02:02 Install new timing chain
- Install hub on crankshaft
04:23 Install camshaft adjusters
- Position adjuster to camshafts
- Screw in camshafts central bolts and release again by 90°
- Screw special tool 119340 into the cylinder head
- Pre-tension timing chain with special tool 009460
- Tighten camshaft central bolts
07:51 Install hub and MAIN bolt
- Find a suitable position for special tool 119280
- tightening central bolt
09:10 Remove timing tools
09:53 Check timing
10:55 Test elongation of NEW timing chain
- with a special tool 2353281 (117200)
- Engine N13: Screw in special tool WITHOUT shim
- New chain tensioner
12:32 Install vibration damper, drive belt, water pump drive wheel and friction gear
14:09 Install cylinder head cover
- Spark plugs and clean all sealing surfaces for valve cover
- Clean cylinder head cover and replace all gaskets
- Camshaft sensors
- Seal all edges and contact points on the cylinder head
- Loctite SI 5970 sealing compound
- Detach ground cable at screw connection.
- Secure bolts for cylinder head cover in the sequence 1 to 12
19:59 Install DME holder
- DME control unit
21:21 Replace clean air pipe for turbo charger
- tank ventilation and engine ventilation lines
22:51 Start engine after timing chain replace
24:12 Filling cooling system
- without vacuum filling unit
26:27 Oil service
- new oil and oil filter
- Do not exceed upper marking of oil dipstick
- Excessively filled oil is causes damage to the engine.
28:45 All back in place
- sound insulation of the upper part of the bulkhead
- trailing link on spring strut dome
31:02 Test drive and check oil level via oil dipstick
- Read fault codes
Let’s continue with the next episode! Stay tuned!
--
Watch this video!
If you liked this video, press the LIKE BUTTON, SUBSCRIBE channel, leave COMMENTS and SHARE content! By doing so, you will be able to support this RU-vid-channel!
Thank you! I appreciate it! 👍
Watch my previous videos on RU-vid related to the maintenance and diagnose of BMW F20 with engine N13!
See the whole series from here:
• BMW F20 - Diagnosis an...
--
My purpose is to encourage people to do things themselves!
Plus, this is a nice hobby for myself and at the same time I have the opportunity to save a lot of money by doing all the maintenance myself!
I’m not a professional with cars or motorcycles, I just want to learn how to do things myself.
If you do this service yourself, always check the correct instructions in the official service manuals. This is just my way of doing it!
Jani Voutilainen
You can follow me also in:
INSTAGRAM: / voutilainenjani
FACEBOOK: / jani.voutilainen
RU-vid: / janivoutilainen
Thanks for Music:
Hybrid Cinematic Gaming Cyberpunk | URU by Alex-Productions | / @alexproductionsnocopy...
Music promoted by www.free-stock-music.com
Creative Commons Attribution 3.0 Unported License
creativecommons.org/licenses/...

Авто/Мото

Опубликовано:

 

19 июн 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 57   
@Erkin95
@Erkin95 7 месяцев назад
Thank you sooo much man! Your videos helped me and encouraged me to replace the chain myself and I did it!
@ManoT-fv1hy
@ManoT-fv1hy 6 месяцев назад
Thanks for this video, will save me lots 👏🙌
@wanmonster2845
@wanmonster2845 10 месяцев назад
Thank you so much for this wonderful video, help me alot on how to diy on this N13 motor. Hopefully you will do a full video on how to rebuild this N13 engine. Thank you for the guide and step by step process. Awaits for you next content. You are the best teacher😊😊👍👍
@rolandgovender5791
@rolandgovender5791 2 месяца назад
Thank you your video was a very helpful
@mentorman6285
@mentorman6285 2 года назад
Thanks for sharing Great content- found it very informative Just changed mine & it cost a lots of Rands
@damionatherton7312
@damionatherton7312 Год назад
Thank you so much 💓
@owenjones2931
@owenjones2931 Год назад
Your videos are excellent, I'm going through the process myself - where do you find all the torque settings for the engine bolts? BMW reference information is hard to find online (I am replacing a head gasket). Also - did you re-use the cam sprocket bolts or replace them?
@jackg7492
@jackg7492 Год назад
Hi Jani, just wanted to say thanks very much for your excellent videos, I have the same car and will be doing my own maintenance... Your work is fantastic! 👍
@williamherbomez1223
@williamherbomez1223 6 месяцев назад
Merci super
@amirardi8857
@amirardi8857 5 месяцев назад
Hey man, thanks for the videos, I really enjoy them. I have a question, though: is the position of the VVT on the camshaft important? I lock the crankshaft and camshaft precisely as you show, but I am not sure if it will work when I try to put it back.
@77luisf
@77luisf 9 месяцев назад
Hi Jani, thanks a lot for your videos. They are very very usefull. I have an F20 118i auto from 2013 and will do some maintenance with your videos. Now it has 102000Km. Major problems : false alarm from expansion tank and oil consuption. I saw you resolve oil consuption with valve steam covers replacement.....but before trying that i will change valve cover: notice some little oil leaking all over edges and spark plugs are a bit wet with oil.....my question : why didn’t you put loctite seal product all around in metal edges? Thanks again for your educational vids.
@joegoh1968
@joegoh1968 2 года назад
I wish you had done this video 3 years ago. I had to replace my valve cover and there was no manual around.
@matteobragato4228
@matteobragato4228 9 месяцев назад
Hi! When filling up the coolant, did you start the engine with the air filter off? Doesn't that possibly damage the engine?
@satti7775
@satti7775 Месяц назад
That is so helpful video could you please tell us how much it cost? And can u do it for me mine has same issue too I have bmw 116i 2005
@jackg7492
@jackg7492 Год назад
Hi Jani, What is normal oil usage for this engine? Cheers, Jack
@mrspriggandv9472
@mrspriggandv9472 Год назад
Hello just quick question does have a timing mark in the cam gear to the chain?
@jackj2182
@jackj2182 Год назад
Hi do u know the torque spec for the serpentine tension please? N13 also
@user-mi1jb5wg7i
@user-mi1jb5wg7i 4 месяца назад
Hello, the torque wrench your using is it the same all the way through the build and what brand and type is it thank you, a grave quoted me thousands to do this repair so doing it myself thank you
@zsoltjonas649
@zsoltjonas649 8 месяцев назад
Hi Jani. where can the cooling water be drained completely? Thanks Zsolt.
@TeroM86
@TeroM86 2 года назад
Hello. From which manufacturer you bought timing set?
@HB-wu4kg
@HB-wu4kg 2 месяца назад
kiitos etukäteen ja hienosta videosta. Kertoisitko? Saisiko lainattua jostakin BMW N13 ajoitus , lukitus työkalut? vai onko pakko ostaa?
@7shaneel
@7shaneel Год назад
it would be nice to add the parts number as well. well done :)
@RBDET25
@RBDET25 5 месяцев назад
Hello what temperature do you get on idle and while driving? What is normal for these engines please
@thebricoapple5134
@thebricoapple5134 10 месяцев назад
Hello excuse me you can change timing chain on m50b20 bmw e34 520i Please
@betounivazo3452
@betounivazo3452 3 месяца назад
Hello friend, I have a problem with my mechanical BMW 114i 2014 N13 1.6 turbo engine. The car vibrates and has no power when driving, an unstable relationship. I changed the injectors, the pressure can pump, we tuned the car, new spark plugs, new coils and the problem remains the same. Have you ever experienced a similar problem?
@Marcell-ux7rb
@Marcell-ux7rb 2 года назад
Hi Jani , do you have a video on how to change the timing chain on n43 318i 2008 ? Thank you, I appreciate it!
@JaniVoutilainen
@JaniVoutilainen 2 года назад
Hi! Watch my video series of rebuilding the N43 engine. It also includes a timing chain: ru-vid.com/group/PLFua3BdQQbC-1ra85BIaLGknOZHuAgouq
@razvanursache9493
@razvanursache9493 2 года назад
Apparently it's easier to replace it on BMW than Mini and Peugeot because of the way of the engine placement. Otherwise the engine is the same as Mini and Peugeot/Citroen.
@PUREPRODUCES
@PUREPRODUCES Год назад
Hi I replaced my timing chain I followed your video step by step and I now have a engine light on for camshaft intake stuck would really appreciate your advice on this
@JaniVoutilainen
@JaniVoutilainen Год назад
Sad to hear! Did you solve the problem? Hard to say what has gone wrong...
@Jokesxxl
@Jokesxxl 2 года назад
Yesterday is replaced my timing chain with youre guide! Tank you very much for sharing!! How much oil does youre f20 use?
@JaniVoutilainen
@JaniVoutilainen 2 года назад
Great that the video has been helpful! 👍 I haven’t been following oil consumption so closely, but I think consumption is normal
@Jokesxxl
@Jokesxxl 2 года назад
Mine use about 1 litre at 2500km… replaced already the pcv membrane valve etc, but stil some oil inside the inlet. Should i replace the complete valve cover? Couldnt find any cracks
@currysini85
@currysini85 2 года назад
@@Jokesxxl Try other oil! 0W40 or 5W40 with BMW LL01 worked fine for me. Now it needs 1 Liter oil on 10.000 km. The "recommended" 5-30 LL04 (which is designed for Diesel-Engines) is burning up on the pistons since oil-temp is already sitting around 115-130°C. Same reason the oil looks tarish after 2000-3000 km.
@Jokesxxl
@Jokesxxl 2 года назад
@@currysini85 yes i replaced 1 month ago the oil with Liqui Moly 5W40 top tec 4100. Oil consumption is now 0.3liter @ 2000km! Car has done 139.000km. The only thing what doesn’t make clear for me is that the fuel consumption and power is better with 95 e10 than on 98 e5 fuel. The car is tuned to 225HP.
@currysini85
@currysini85 2 года назад
@@Jokesxxl I use the same oil! Will get even better, when the piston rings are cleaning up again 😉. Mine is around 140.000 km with the same Stage 1. Now the chain seems to need a replacement. Well I had knocking with E95 under full trottle.
@SuperBasshunters
@SuperBasshunters 2 года назад
Engine looks dirty under the valve cover :( Do you reccomend to change tensioner at 60000km?
@JaniVoutilainen
@JaniVoutilainen 2 года назад
It is worth changing in good time. My car has been driven about 160 tkm and it had broken like in the video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-_dZ6cuqy69A.html Easy to change, and no expensive investment. I can't say the exact kilometer limit, but I know it's worth changing in good time! 😉
@ubuntutorials
@ubuntutorials 2 года назад
Hy Jani, Thanks for the video .. two questions if you may .. 1. I see that are for sale timing kits with and without the inlet/outlet camshafts (11367545862 / 11367536085). (The difference in price is quite considerable between the two) A worn chain doesn't affect in time also the camshaft wearing it ? ... (wearing the teeth). When would be recommended to also change the camshafts? 2. Do you have any recommendation for a specific kit manufacturer ? In my country VAICO sells a full kit with camshafts .. next in quality/price would be FEBI Bilstein (without the camshafts) Thanks in advance
@Jokesxxl
@Jokesxxl 2 года назад
Why do you install the old tensioner before when you turning the engine by hand? And witch brand of chain set did you use? Did you had also oil consumption and gone after changing the chain?
@JaniVoutilainen
@JaniVoutilainen 2 года назад
Timing chain set is bmw original set. There is other brands with good quality cheapr prices that you can use if you want 👍. Used old chain tensioner, becouse I want to show and compare elognation with new chain vs old chain in previous videos. Its recomended, that you tighten chain tensioner once.
@Jokesxxl
@Jokesxxl 2 года назад
@@JaniVoutilainen thankyou for you’re feedback, ive ordered the Febi kit, hopefully it will last. But did you had also oil consumption?
@JaniVoutilainen
@JaniVoutilainen 2 года назад
Febi is Ok. I used Febi brand for timing chain set for E91 with n43 couble years ago. Oil consumption of mine F20 was normal 👍
@Jokesxxl
@Jokesxxl 2 года назад
Mine uses around 1liter @ 2500km… changed already pcv membrane, looking for vacuumleaks, cleaned my intake valves. It has only 126k on the clock… you got some ideas? Its the 2013 114i version.
@clintstechtips6571
@clintstechtips6571 2 года назад
Timing chains are supposed to last the life of a car. Anytime honda or toyota put timing chains in their engine they are pretty much good. The rest of the car falls apart first before the engine. BMW and german cars in general on the other hand, your tyres will probably last longer than the chains. What a farce.
@blame182
@blame182 2 года назад
it has oil dipstick oO
@JaniVoutilainen
@JaniVoutilainen 2 года назад
Thin engine model, Yes it has! 😁
@franzbaur2766
@franzbaur2766 Год назад
BMW wäre ein gutes Auto wenn in ihren Motoren nicht so ein schlechter Dichtgummi und sehr schlechter Kunststoff verwendet würde.
@bijdikh8516
@bijdikh8516 Год назад
There's a special place in hell for just about every single N series BMW engine. N12, N13, N14, N16, N18, and the twin turbo N54 engine are all garbage. I don't care about the tuning potential of the N54, it's trash and belongs in the dump. I did oil changes on my N18 every 3000 miles with a filter change, and did every other service you could ask for. Changed the PCV valve just as preventative maintenance, changed coolant at 95k miles, changed both front and rear brakes recently, and changed my spark plugs at 100k miles. Despite that, the car was leaking oil from the oil filter housing, it started a new vacuum leak from the valve cover, the EVAP system started failing despite no wiring issues and not having any EVAP leaks, the Airbag system was failing from god knows where, the timing chain tensioner failed at 104k miles despite the whole assembly being replaced at 70k miles, and the engine now has misfire issues when trying to give it anymore than a quarter throttle.
@fxly
@fxly 2 года назад
Why oh why a plastic guide rail 😅
@JaniVoutilainen
@JaniVoutilainen 2 года назад
I think the metal chips in the oil sump are worse than the pieces of plastic 😉
@alexbuza1550
@alexbuza1550 Год назад
Because it is less noisy, probably?
@adibsilo2089
@adibsilo2089 2 года назад
Bitte kannst du schicken Telefonnummer weil ich möchte Frage
@enjoylife756
@enjoylife756 2 года назад
Itsellä vaihdettu 2019 Laakkosella koska venymä jolloin 85k mittarissa,nyt 127. Kohta varmaan pitää vaihtaa uudestaan ettei paska leviä ihan kokonaan 🤣 On nää hyviä tekeleitä 👎 Mikään ei oo vieläkään saanu mua vakuuttuneeks että uusi versio kestäisi yhtään paremmin 👎
@JbernardH
@JbernardH 11 месяцев назад
Hello, I have replaced a timing chain same engine to this exact procedure, the engine was rough before but now runs smooth, 2 codes appeared after driving vehicle for vanos, any help you can offer? P13c9 and p13c0.
Далее
small vs big hoop #tiktok
00:12
Просмотров 3,3 млн
N13 Engine ALL Issues (BMW, MINI - N14, N18)
15:20
Просмотров 25 тыс.
Wymiana rozrządu 1.6 THP Peugeot 3008
27:51
Просмотров 312 тыс.
N20 Engine Timing + Reassembly - Project 328i Part 4
44:46
Замена цепей BMW N20
49:07
Просмотров 87 тыс.
POV N47 TIMING CHAIN + UPGRADES!!⛓️💪
13:55
Просмотров 12 тыс.
Легкий тюнинг 🤣☝️ #goodcarkz
0:26