Installing a Mustard Bikes tail tidy on a 2014 MV Agusta Dragster 800

Подписаться 2,2 тыс.

Просмотров 16 тыс.

50% 1

A step by step run through of the installation process for the Mustard Bikes 2014 MV Agusta Dragster 800 fender eliminator.
This product is available from the following link:
www.mustardbikes.com.au/14-20...
This video should help you understand where parts are and how to install your fender eliminator, it is a comprehensive how-to and should allow most customers to complete the installation on their own.
If you experience installation issues please contact us via our help email provided on your product card, we are always happy to help where we can!.
Thank you for watching, and don't forget to give us the thumb's up and subscribe!
Tail Tidy: www.mustardbikes.com.au/14-20...
Mustard Bikes Apparel: www.mustardbikes.com.au/apparel
Website: www.mustardbikes.com
Facebook: / mustardbike
Instagram: / mustardbikes
0:00 Intro
0:35 Required Tools & Box contents
1:17 Removing the stock fender
3:34 Replacing the axle pinch bolts
3:48 Accessing the wiring
4:56 Re-routing the wiring
6:49 Fitting the tail tidy to the bike
8:11 Re-connecting the wiring
8:48 Aligning the tail tidy
9:35 Finishing up and Outro

Авто/Мото

Опубликовано:

26 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@russkle2042 2 месяца назад

Top man thanks 👍

@JUSTINPETERS33 Год назад

Rad! tyvm

@yandy3xxx 5 лет назад

Please pay close attention to the part where he says to replace the bolts with the provided ones... if you try to put the same bolts back in your rear wheel, they will not sit all the way in and will cause your chain to sag and make a very unsafe ride.

@neilplumb2204 6 лет назад

You will need 10w 39ohm resistors to get indicators to flash at correct rate if fitting after market led indicators

@MustardBikes 6 лет назад

Hi Neil, thank you for sharing this.

@wayne9290 5 лет назад

Do you have any oem rear license plate fenders with side arm bracket available for sale? My bike was rear-ended and I need to find a replacement oem fender to fix it. The fender is hard to find in the US. Thanks.

@MustardBikes 5 лет назад

Hi, we only manufacture the product. The bike used was purchased and the OEM arm went with it. Sorry we can't be of more help. You could always fit a fender eliminator! That we can definitely supply.

@mauricioarango9369 5 лет назад

Hi the u have any led buld headlight for mv agusta dragster 800rr 2017

@MustardBikes 5 лет назад

Hi Mauricio, unfortunately this is the only Dragster 800 product we make.

@jaredturner6131 6 лет назад

What about indicators?

@MustardBikes 6 лет назад

Hi Jared, This product is designed for use with most aftermarket 8mm bolt style mount indicators. As they are relatively simple to fit, but are also all different in design we opted not to include their installation in this video. Due to the design and size of the original indicators and the interference they would cause with brake light visibility it was chosen not to use these. We hope this helps!

@2201emperador 4 года назад

I have a MV Agusta Dragster 800 RR 2019. I would like to know if it works for my motorcycle.

@MustardBikes 4 года назад

Hi Julio, Unfortunately this does not fit the new shape 19 Dragster 800RR.

@2201emperador 4 года назад

@@MustardBikes thank you for your response. Please, continue with your canal, it help us very much!

@mauricioarango9369 5 лет назад

Can you play the middle harness because I can really see in the video it's too hard to see the photo thanks

@MustardBikes 5 лет назад

Hi Mauricio, you need to cut the cable tie holding the wiring harness and ABS line together (be careful not to cut the lines). We were unable to get a clear image with the camera, hence the photo. If you look into the area circled by the red circle and follow the wires you will find the cable tie we are talking about. Hope that helps.

@mauricioarango9369 5 лет назад

@@MustardBikes thank you for you help

@mauricioarango9369 5 лет назад

I have 2017 mv agusta dragster 800 rr the fit in my bike

@MustardBikes 5 лет назад

Hi Mauricio, yes, this will fit your bike.

@Bapekq 5 лет назад

bro when u remove the rear guard tail u use OEM bolts to put it back?

@MustardBikes 5 лет назад

All the required bolts are supplied in the kits.

@Bapekq 5 лет назад

Mustard Bikes is everything on this bike same on the Rivale?

@MustardBikes 5 лет назад

@@Bapekq the Rivale is completely different to the Dragster. This product is designed for the Dragster 800 only.

@Bapekq 5 лет назад

@@MustardBikes oh ok thank you,it looks the same lol

@Bapekq 5 лет назад

@@MustardBikes u have kit for Rivale?

@vincentthenaux8754 2 года назад

Hello it’s ok for 800 dragster RR 2015 ? Thank you

@MustardBikes 2 года назад

Hi there, Yes this fits the 2015 RR!

@vincentthenaux8754 2 года назад

@@MustardBikes thank you for the answer, the two screws are provided for the oscillating arm ? Thank you

@MustardBikes 2 года назад

@@vincentthenaux8754 yes the two bolts are provided.

@Godzilla-it6sc 2 года назад

Does this fit the rivale 800?

@MustardBikes 2 года назад

Hi there, unfortunately no, it does not fit the Rivale 800.

@yandy3xxx 5 лет назад

@MustardBikes 5 лет назад

Good point! And the reason we supply the extra bolts.

@MustardBikes 5 лет назад

@A1 J1 they are a 50mm bolt.

@MustardBikes 5 лет назад

@A1 J1 we aren't aware of anyone that makes one that mounts there. If you do remember to take into account the rear suspension travel. The bolts we supply do not have the hole down the centre. The hole is just weight saving, and quite common on high end or competition motorcycles.