Installing a vent for the Thunder USA Nova 51 Laser

Подписаться 1,8 тыс.

Просмотров 30 тыс.

50% 1

After unboxing the Thunder USA Nova 51 Laser, my friend Jon from O Dark Thirty Woodworks had to prep the shop for the venting of the laser.
Jon used a 6" hole saw from Spyder products. He first used a long drill bit to make a pilot hole all the way through the drywall, foam insulation, OSB, and vinyl siding. Then we installed the dryer vent housing. This was as easy as it looked.
Support Mike on his social media accounts:
Website: www.marrazzowoodworking.com/
Instagram: / marrazzowoodworking
RU-vid: ru-vid.com/show-UCokB...
Etsy: www.etsy.com/shop/Marrazzowoo...
Facebook: / marrazzowoodworking
Check Out Mike's Podcast!
Follow Handcuffs & Sawdust on social media:
Instagram: / handcuffsan. .
Facebook: / handcuffsand. .
RU-vid: / @handcuffssawdust3592

Хобби

Опубликовано:

2 ноя 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 28

@TheOrishas 2 месяца назад

Hell Yeah

@glasswinder 8 месяцев назад

I need one thru a block wall.

@marrazzowoodworkingdiy8118 7 месяцев назад

That should be a similar process, but just with a much bigger drill. good luck!

@godzillal123321 Год назад

Does the alignment have to be perfect? How do i know where to drill from the other side

@marrazzowoodworkingdiy8118 Год назад

We drew the diameter of the circle on the inside, found center, used a really long drill bit to drill all the way through as a pilot hole, then went outside and placed the drill into that pilot hole. It came out perfect.

@BlackManSideProfile 7 месяцев назад

How do you know where to drill on the outside when it doesn’t appear you drilled all the way through? Did you use a special tool did you stick the drill bit all the way through the house?

@marrazzowoodworkingdiy8118 7 месяцев назад

In the beginning of the video and process, we drilled a center hole with a really long drill bit. Then just went to the outside, placed the center of the hole saw bit in said hole, and drilled.

@Jwebbplayz 7 месяцев назад

@@marrazzowoodworkingdiy8118 can you share the bit type you used to go thru house? I see a lot on Amazon for wood, ect. 1 footers, suppose that’s probably fine huh?

@marrazzowoodworkingdiy8118 7 месяцев назад

@@Jwebbplayz I will ask my friend Jon and get back to you.

@marrazzowoodworkingdiy8118 7 месяцев назад

@DestinyGrind. My friend Jon told me he got that bit at Lowes, but doesn't remember the name. And big box store should have them. I found this: Drill America - DWDDL18X3/8 3/8" x 18" High Speed Steel Extra Long Drill Bit, DWDDL Series a.co/d/eL9TPGC

@Jwebbplayz 7 месяцев назад

@@marrazzowoodworkingdiy8118 cool, thanks man.

@Jwebbplayz 7 месяцев назад

I see the cap is on straight to siding? I was going to cut a square of allura trim and insert it into the cutout siding “mounting” the cap to that.

@marrazzowoodworkingdiy8118 7 месяцев назад

Yes, my friend Jon decided to finish it off this way with just some caulk. it worked out well, but the method you want to incorporate would probably look more finished. Good luck!

@hoho9334 10 месяцев назад

Question, I have pink insulation in my walls. Do I need to put anything between the vent pipe and the insulation

@marrazzowoodworkingdiy8118 10 месяцев назад

I don't believe it's an issue since it's glass and not combustible. But I found this for you www.hearth.com/talk/threads/fiberglass-insulation-against-vent-pipe.13244/

@iTN224 Год назад

What tool is that to make the circle

@marrazzowoodworkingdiy8118 Год назад

It's a 4" hole saw made to cut drywall, OSB, and siding.

@asmith7812 8 месяцев назад

But - how do you seal it?

@marrazzowoodworkingdiy8118 8 месяцев назад

Just like any dryer vent, use sime outdoor caulking around the vent box where it contacts the siding/brick.

@alexforeri Год назад

How you know is no cables or water pipelines?

@marrazzowoodworkingdiy8118 Год назад

The structure was only framed out on the inside with no drywall, electrical, or water lines. My buddy in the video with me had a contractor add power and drywall and knew exactly where the laser would be going. So he knew that there were none of those things in the wall. I hope this answers your question. Thanks for asking!

@HawkGTboy Год назад

Ok… and how do you secure the vent to the exterior wall?

@marrazzowoodworkingdiy8118 Год назад

Four screws, through the siding, into the wall. Then caulk. Nice and tight and sealed.

@HawkGTboy Год назад

@@marrazzowoodworkingdiy8118 Thanks. Didn’t mean to come off like a jerk. I discovered, to my dismay, that my exterior walls don’t have any OSB to screw into. It’s just a 3/4” thick layer of polyiso foam board behind the vinyl siding. I had no idea that houses could be built so flimsily. :(. I just moved from a brick house built in the 40s into what feels like a disposable house.

@marrazzowoodworkingdiy8118 Год назад

@HawkGTboy you didn't come off as a jerk at all. Don't worry about it. That sucks! I've never seen that in a house, so I'd be pissed too!

@georgebradley6811 9 месяцев назад

Slip two small vertical pieces of sheet metal under siding and trust a friction fit sheet metal to foam board & screw 4 corner screws thro siding into sheet metal. To sandwich the metal to the back of siding. Go inside & spray foam or caulk tube to dry wall. Using wax paper to contour & shape for a more finished look. Look for more ways by asking the HVAC guys.

@marrazzowoodworkingdiy8118 9 месяцев назад

Thanks for the assist!!