Installing a vinyl wrap - cornhole boards 

Great video! I've been dreading doing mine, but I'm a lot more confident in putting them on now. Thanks

Really enjoyed the video , Now I feel comfortable in starting my wraps I did get them done but have been very hesitant in doing them didn’t want to mess them up ! Thanks Great Instructional Video

Thank you for the instructional video. The company I purchased my wraps from said it wasn’t necessary to put on the acrylic (on the actual board or the wrap). I like how you did in the video and I will be doing it your way which make good sense to me. Thank you again!

I bought a set and I’m going for it! Thanks you made it look easy!

Great tutorial. Thanks for sharing!

Thank God someone finally put the union on the correct side!

Awesome video! Thanks for the information.

I quit using the plastic squeegee. Started using a rubber roller. Zero scratches and can press harder. But I router the hole with a round over bit so it makes it difficult to cut it out clean

Great video, thanks for sharing

The paint store has a tack cloth to remove all dust particles. The brush & hand won’t clean all the dust off. FYI

Keep up the great videos 7

last i heard you were finishing my wrap. Is it finished and when will it ship and how so I can be on the lookout it? Thanks

Blowing off with compressor works better than hand

Great video. The boards I have were given to me painted (Miller Premium Enamel, Alkyd Enamel, white). We are installing vinyl wraps. A few questions: 1) should I sand it off completely or just smooth it out. 2) once smooth, should I apply another coat of the primer/paint or should I apply a coat of the Polycrylic, or ??. 3) Assume everything else with the install is the same from that point, starting with the spray adhesive...

I play a lot on TCL sanctioned boards. How do these compare speed wise with one coat of polyurethane? ACL boards have like 6 coats. Thanks

Enjoyed the video. I’m all about overkill but I regret using the spray adhesive. I attempted to spray the edges and I guess it came out clumpy. So all of that work sanding and smoothing out the poly was for nothing. I lost a whole wrap due to trying to fix it/smooth it out after I laid the vinyl out. Probably something that helps when you’ve been doing a lot of these

What grit are you using after the poly? Too fine and it'd get clogged, too rough and you're leaving rough edges. Process looks solid!

This was a great tutorial. I have been finishing cornhole boards for less than one year and I am still refining my process. Do you use polycrylic on ALL of your vinyl wrapped boards?

Thanks for the great video. I was told to wait 30 days to allow for the sealant to cure before applying the wrap. What are your thoughts regarding that? Thansk

You do very well answering questions. I’ve been getting bubbles in my polyacrylic when it’s dry. How do I stop that from happening on my final coat so I don’t have to keep sanding them out?

How doe this interior finish last in the elements? How well does it stick to the vinyl? I have seen this finish not hold up in exterior environment.

Any ideas on how to apply the vinyl on rounded corners? I make my boards with round corners vs sharp and always have trouble getting a smooth application without getting any creases. I also tuck my wrap around and under the edge to help avoid the wrap from peeling up

Can you use this strategy for putting normal stickers on a cornhole board as well or only a vinyl wrap?

Where can I order the different designs of vinyl? Also any marketing suggestions? I also make custom silhouettes and added the words that I make cornhole boards but haven’t gotten a single request/order

Hello, I followed your instructions and the boards came out great but two weeks later the wrap started to peel from one of the corners. Any suggestions what I could do at this point.

New/update install video on laminated wraps and installing lights coming soon 👀

great video! Do you find the wraps that don't need the heat gun hold up just as well?

Can you do a tutorial on how to print the Vinyl wrap?

I've done decals before, but never a wrap. So, at the risk of asking a potentially stupid question, can the wraps be replaced with a different wrap down the road? I thought I read that somewhere, but can't understand how that is possible if you're placing a coat of polycrylic on it.

Question! I ordered some cornhole boards off of Amazon, I was going to lay down wallpaper and then a vinyl decal over the top of that. What is the best process for me to do this and have it durable for outside etc

Is the squeegee I need one that has felt on one end? Also, is ther another lining step needed if the wrap already has a hole printed on the vinyl where it should be cut? (To ensure it lines up) Thank you for the wonderful and informative video!! :)

Really nice video. I would like to make my own vinyl. Do you know what and where I can purchase the machines/equipments to do so ? I am living out of the U. S. and it's going to be way too expensive with shipping and customs charges to be trying to buy them from a company in the U. S. for my business. Thanks

I just installed some wraps and put acrylic on them. The acrylic peeled off the next day. How long do you wait to sand after applying 1 coat on the vinyl?

I have the birch plywood, do need to any special prep work before putting a laminate wrap on?

Hey if the vinyl is laminated do you still poly over ? It won’t hurt it right ?

Great vid, thanks. About to put my decal on, Don't Tread On Me and American Flag on my board. Going to do a 2A decal next. And remember to...Keep America 2A Strong...

I currently have a raw wood board. Before I apply a wrap should I polyurethane to the top of the raw board to help protect it? OR will that action cause the wrap not to adhere properly? Thanks, Kurt

It seems there are 2 camps out there. Those that say 1 to 2 coats are enough. The other says 5 to 10 coats. I my self don’t want my boards too slick. Im ready to apply wraps in a day or two. The back side of the wrap says ORAJET Rapid air. It is laminated. I’m not even sure if using a heat gun is required to apply these. I’d rather go two coats, sand then be finished. I’m using semi gloss Spar Urethane. Because it is semi gloss, I hope it doesn’t dull the look of the wrap. It’s made the paint on the sides of the board and the underside look glossy so I guess I can use it with no concerns.

is the vinyl very slick for the bags or about the same as if it were paint?

Do you know the difference between laminated and non laminated wraps? If so which one is better?

How do you get the polycrylic so smooth? Mine are always streaky. And I use foam brushes.

What type of water sealer was that one gallon can and what kind of spray was that the adhesive

Awesome

LIFE SAVER!!!!!!!!!!!

Nice video. How would you finish a board that is only partially wrapped with just a decal in the center?

What is the spray your using before putting on vinyl? Live in Wisconsin don't want it to come off

I have been hand painting cornhole boards and coating them with epoxy resin. Can the wraps be coated with epoxy also ?

Is the wrap that you use (linked in your notes) $65 for a set or just a single wrap? Also, are the ones you used laminated or not?

Love the wrap but my ocd kicks in cause the board planks don’t look like there lined up.

Very nice tutorial! What type of vinyl are you using? I have a 54" ecosolvent printer and would love to make a set for personal use. :)

Hey new follower here love the video what type of printer do you use , if any ? I am new to this so forgive me but was wondering how to create graphics of my choice on to the vinyl and what size ? TIA

When I get the 220 grit for the end. It looks like it leaves scratches on the poly. Any idea?

so are the wraps already laminated? and you add another layer of poly? Thanks for the video.

I don't see how the finish can properly adhere to the shiny surface of the vinyl. As a professional woodworker & finisher, the poly would need a scuffed surface to bite and adhere. How long does it last before peeling off?

Can and/or should you put a sealer on the wood before you install the wrap

Thanks

Slighty unrelated, but I was hoping that you crafty ladies/gents might be able to help me or at least point me in the right direction. We are going to be using corn hole boards as our guest book at the wedding this Summer. I wanted something different, and at least this time, whenever we play we will remember the day. ANYWAY, the board is covered with a customized vinyl wrap with our last name on it. What would be the best to have guests sign with and still be able to seal after (and what would be the best seal that isn't going to degrade when sealer is applied) I thought black and or metalic sharpies, but wasn't sure how they would hold up under a seal coat. Then I thought OOOO A Paint pen, but then do i do water/oil based? I'm so confused

Can you supply me with links for the edge and hole cutters? TY

So I put the acrylic on top of the vinyl and it has a white haze, how do I get it clear?

where is the best place to get the wraps do you make them ?

Do you make custom vinyl like names and stuff?

Where do you source the vinyl prints?

So who do I order my vinal wraps from that does not require heat shrink ?

Do you print custom vinyls for cornhole boards if so how do I get in contact with you to have some printed ?

I did it wish I could show it!

That looks like an old Craftsman router table. Much like mine. LOL BTW, does the squeegee come with the decals?

Why not use laminated wraps instead? They're more durable & no need for a clear coat, correct?

How did you attach plywood to 2×4 frames

Are your wraps Cast Vinyl or Calendared? Awesome design and colors!

Where do you order your Wraps from? Great video thanks

What type of spray can did you use?

Hey I’m doing my own corn hole board can you Tex me all the things I need I have it built I just need to no what else’s I need to get and all so how much does those scenes cost I want to personalize mine see I’m a dj and I want to put at the bottom a man and woman on each side with turn tables in between the man and women and around the hole I want dj steady

What machine do you use for printing the vinyl?

What is the cost for you to help with the design and print them?? Then ship to me?

Where do you get your arcrilycs made?

Your vinyl is so flat and doesn’t roll up. How you you get so flat? And we are having trouble with our vinyl lifting on the edges. How do we stop that?

Would like to see how you made your legs for this game

What type of vinyl printer do you use

were do you get your vinyl wraps from?

What vinyl do you find best to use?

I learned a lot, thanks. But if I owned it the triangle not lining up with the hole would drive me nuts

Do you laminate the vinyl before mounting?

I thought a vinyl wrap does not need a coating on top ???

What finish polycrylic do you use, gloss, satin or high gloss?

Very nice wher do get your Vinel

What is a source for the wraps??

Where can I purchase the wrap?

Do you make your own rap, or do you get it from someone else

I’ve never seen sanding before that didn’t create dust in the air

How can I buy one ?

22 minute video that could have been a 9 minute one 😵‍💫

Went on your website and I see many flag wraps that are not displayed / made correctly. When displaying the American flag vertically, the star field should be upper left. Some are correct but the ones that are not should be corrected to show respect. You have a lot of good products, please respect the American flag that's all I am asking...

Good video but I have a bit of a problem with the actual design. The flag is backward (negative side of a print). Only active duty soldiers wear the flag in that position as a statement that they are returning home.

Apple AirPods with an LG phone?

Yeah how does that make the board play? Must be slippery as fuck

Poor sound, can’t really hear what is being said.

Good video if I didn’t have to watch you swallowing your saliva so much. Try getting rid of the cud when doing videos.

don't need too watch you sand