JEEP JL SUBWOOFER INSTALLATION JL AUDIO ACS112LG-TW1 12" powered subwoofer 

I did pretty much the same... But you took the time to film and explain it all for someone who hasn't done anything like this! Major props to you... Great vid!

I’ve watched a lot of videos on subwoofer installs and you’re the first person to show where you tapped in for the audio! Thank you!

Nice video, I just installed a sub in my JL and followed your instructions. Worked perfectly. The remote turn on and high level inputs are exactly as you explained.

I also don't have the Alpine system and I agree that the factory stereo sounds really crappy. I was hoping someone would do an install like you did. I'm going to try it in my JL Thanks for sharing 👍

Thank you for the excellent install video!! Sub shows it’s out of stock. Hopefully they get more in soon.

Nice job...I had the same base sound setup in my wrangler jl and initially added the jl audio 8" powered sub in the same location on the opposite side hooked up to a bass knob up front near the emergency brake. It filled in the bass, but the factory front and soundbar speakers aren't good. The key to getting it sounding good was making the speaker enclosures bigger to fit Hertz 5.25" components up front and 5.25" coaxials in soundbar powered by a 4 channel alpine pdr-f50 under the driver seat. To get a clean signal, all of this is ran through a jl fix 86 sound processor hidden under the steering wheel behind the plastic trim piece. I kinda wish I went with the bigger jl audio 10" 400 watt powered sub bc I have my input sensitivity at 80% and bass turned up all the way most of the time. One annoyance is jeep setup the bluetooth volume to default at volume level 15 and when the speakers are amplified, I manually turn down the bluetooth volume to 10 or so every time you make/receive a call or else it's too loud. Jeep needs to allow the radio to remember the last bluetooth volume level and stay on it. My system sounds better than the factory alpine, but cost more.

Alpine system I actually liked , but I did upgrade my dash and sound bar mids to Kenwood 3.5 coaxial

I iust ordered this exact JL Powerwedge+ yesterday but forgot to get the wiring kit. I tried using the link you have in the description but it won’t take me to the Amazon link. Can you tell me which wiring kit you used, I want wire this bad boy up in my 4Runner when the sub gets delivered. Great video and I hope it will sound as good as it did in the video regardless of how bad GoPro mics are, it sounded good with headphones on. 🤘🏼😎🤘🏼

I put 2 of these in my 68 mustang and it slaps hard. Btw good vid!

Funny, I only watched this to see how you were supposed to hook up the speaker wires and you showed wires to two different speakers. Did you have to hook to the positive and negative to one speaker or both. Thanks

Hey man, why didn't you go for a ported box. My sound system guy recommended this for my jeep because when I decide to take the top off, the sealed wouldn't be able to deliver the same bass as the ported.

For the speaker harness that you tapped into. Which is the positive and which is the negative lines for each side? You said which sides the colors were for. Installing an all in one box similar to yours.

Did you use a pry tool to remove the floor trim to the back. I am doing it now by hand in a JT and its a pita, having a tough time opening them completely like you.

How does this compare to the stock Alpine upgrade ?

Where do you have your gain knob on yours? I have the same sub and I’ve been turning it up without clipping but I’m a bit nervous to increase it, currently I can’t even hear deep bass when driving in the front seat

Good video, do you have apple play in you head unit? If so, any issues with install?

Great video man, clean and to the point.

Do you have a picture or video of how you connected the wires from the soundbar to the subwoofer? and a picture of the connections to the amp?

Don't these have different settings for turning on..without having to run the remote wire???

Hey bud, great video! I have the same sub but I don’t have any wiring because it was given to me. Can y please add a link to the wiring kit you used? Thanks!!

I have a different powered sub but I’m guessing the install is th same. I have the 7 inch base. By tapping into the sound bar speakers does this mean you don’t need to add a LOC?

Question how did you mount the subbox? I like that idea ..is drilling required?

No LOC needed with this sub/amp combo?

Very well done install! ✨Clean as hell 💯

Did you tap into both speakers in the sound bar or just one?

is there no potentiometer for the amount of bass you want or it the bass solely controlled by the head unit?

Illinois gang!

Best video I have found explaining all the wiring. Thanks so much for doing this and being so detailed. Extremely helpful.

Great detail 👌

Did you have to use a LOC?

Wait a min. If I got the alpine upgrade can I just tap in to those wires?

did you have any complications with the factory head unit cutting sound to the sound bar because the impedance is different with the amp in parallel? i guess not?

Hi - did you need a special harness to connect to the factory head unit?

can you help me run the cables in a patriot jeep for a subwoofer please

What kind of cable did you use to tap into the sound bar speakers?

I have a 2020 Sahara the firewall is different because I have a clutch

Fantastic job

Very clean

Hey man I was thinking about installing an amp with a subwoofer. I called Best Buy just for some advice they told me that the uconnect system will not work with the high input. They said you have to add a ceramic capacitor or something like that is that true?

What song are you playing?

You dont need to run a remote wire when using high inputs

Dude theres no way that we can hear the difference. Maybe you can explain the difference and wether or not it worth it

Every time I look up a subwoofer for a review, some dude with a Jeep is showing how to install it. 🥴

Alpine is a waste of money they don’t support idatalink.