Jeep Wrangler and Gladiator (2016 - present) - New Battery Install (Primary)

Подписаться 24 тыс.

Просмотров 27 тыс.

50% 1

Learn how to install a new 12V battery in a Jeep Wrangler and Gladiator. We’ll show you how to replace/change/remove with simple tips and tricks to help get you started!
Tool List: flathead screwdriver, 10mm wrench (suggest socket w/ multiple extensions to remove hold down bracket)
Click this link to determine which battery your vehicle needs: www.autobatteries.com/homepage
-This video shows how to replace the primary 12V battery in a 2019 Jeep Wrangler. The group size H6 is used in this video.
-The Group size H6 and H7 are used during 2016-present Jeep Wrangler and Gladiators. Both flooded and AGM versions of these sizes are used. BEFORE purchasing a new battery, check the size and type of the battery in your car.
-Note that start-stop models come with a second 12V battery (Auxiliary/Aux). These batteries are available at most retail outlets. Check your owners manual to see if your vehicle has an Aux battery and see our video for instructions on how to replace your Aux battery. • Jeep Wrangler New Auxi...
-To learn more about start-stop, click the link below about Absorbent Glass Mat AGM batteries and scroll down the page.
-Even if your vehicle did not come with an AGM battery, you can upgrade to an AGM battery for up to 2x the life. AGM can be found at most retail outlets. You can learn more about AGM here: autobatteries.com/battery-tec...
-The use of a memory saving procedure will keep the memory alive on the vehicle's computer during the battery replacement procedure. Referring to our Memory Saving video will provide you with various memory saving procedures that can be used according to vehicle manufacturer's requirements. • Vehicle Memory Saving ...
-Although this video may provide you with the basic procedures for replacing your battery, we recommend that you check with the vehicle manufacture's step by step procedures found in service/repair manuals for the vehicle you are working on.
Some late model vehicles must have the 12 volt battery registered with the vehicle's Battery Control Module or Computer after replacement. See these videos on Battery registration and coding for more details on the procedures at • Battery Registration w... & • Battery Registration &...
Always wear safety glasses and gloves when working with or near batteries.

Авто/Мото

Опубликовано:

7 фев 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 10

@Llildookey442 Год назад

The hook under the positive battery table is easily the most annoying thing man has ever created. There’s no reason for it🤣 I should not have struggled with that as much as I did

@TheBatteryShop Год назад

Hi -Thanks for watching and sharing your experience!

@billredding2000 Месяц назад

Thanks for showing how to disconnect the Jeep's positive battery terminal properly/safely (without damaging it, too) -- I don't think any other RU-vid videos show this process. I had never seen this kind of battery terminal design so couldn't figure how -- when the battery was still in the Jeep -- to remove the terminal until after I disconnected all the cables, left the positive terminal still on the battery post, took the battery inside to clean and put it on a charger/de-sulfator (from "BatteryMINDer") for a few days. I could then see how that "camming mechanism" to tighten the positive terminal onto the battery post worked AND more clearly see the plastic "latch" clipping on the the top edge rim of the battery that you have to undo to get the terminal completely off. IMO however, it seems unnecessarily complicated, not to mention an "unconventional" way to tighten the terminal on the battery post itself (and doesn't seem that secure). A very "non-standard" (and unexpected!) obstacle if you didn't know this beforehand as it's unlike most other auto batteries' simple/basic terminals we've had for decades! Jeep is got a bit weird with that design! ;-) -- BR (2021 Jeep Gladiator Rubicon)

@TheBatteryShop Месяц назад

Thank you for watching. Glad we could help!

@djttv 5 месяцев назад

My friend's 2019 jeep rubicon jk does not appear to have fasteners for the battery cables where they connect to the battery terminals. Am i supposed to just pry it off, and then press it back on? I don't think so, but not sure how to disconnect them. I'm missing something obviously. The terminal connector doesnt appear to have any tightening mechanism. Just a solid ring that fits over the battery terminal.