Jura Impressa C, E, and F series Espresso Machine Display of Internal Parts and Operating Mechanism 

I have ordered from you many times over the years mostly for Saeco and Gaggia machines. I am in the process of getting a JuraE9 machine from ebay and anticipate that I will have to make repairs. This is the best video out there to show and explain all of the parts that typically go bad on Jura machines and I thank you so much. I made an order on December 30 and got it on Jan 3. You can't ask for faster service than that!! Thanks again for the help you have provided me and everyone who has asked for it.

Thanks! Well done on the video. It explains the working functions and names all the parts expertly.

very informative, excellent explinations - many thanks to the author

Good job! Thanks

Thanks for this video, How to skip a membrane regulator? a few leaked from this unit.

Hi Parts Guru, Great video and so detailed. It encouraged me to tackle my own machine which is an Impressa F9 that really needed a good clean inside. I was so confident I took everything apart. Even disconnected all wires from powerboard to access underneath it. I took lots of photos but my problem so I know how to put back together again. I did not notice there were two blue wires coming from the solenoid type V32E to the power board were both blue and look exactly the same. So when I went to connect these blue cables to the powerboard I do not know which connects to TM5 and which connects to TM6 on the power board. I am not sure if the two wires are interchangeable so I did not connect them. Are you able to shine some light on which wire from the solenoid goes to TM5 and which one goes to TM6. Any help would be appreciated these blue cables are all that has stopped me from completing the project and turning on the machine.

Thanks for the videos they are very helpful. taking advantage, I have a swear e65 and it marks a general error troubles. Could you help me to know how it is solved. Thank you.

I do have Jura impressa E55 machine. how do I fix or what is the problem when all 4 upper lights turns on.

You had a grinder burr replacement video before, is it still available?

Tnx for video. Can you help me with c5. It looks ok, but ligtht permanently clean led, and mecanizm cycling up and down meny times. Klack-jjjjjjjjjjj-jjjjjjjjjjj-klack-pause20sek-again I suppose, it cycle in cleaning procedure. How I can reset it to put it in normal working? It totally clean , so I remove main mecanizm for revision and clean it. This problem started after broke main transformator (termofuse is broke) I replase it to autotermofuse 85 C.

Hello. I have a Jura Impressa F8. It says I must add beans even though it is full of beans. What method does the machine use to sense that there is "No beans".?

hello where is the bean hopper sensor located on a f60 jura

Thank you for this video! I just acquired a 10-year old E8 machine, which had recently started leaking in a strange way: Every 10th or so cup of coffee, it spills out a cup's worth of water - other than than it runs fine. I plan to order the oval screwdriver from you and take a look - but in the meantime - is there an obvious other part to order/replace? The membrane regulator? Apparently the past owner spoke with Jura USA tech, who mentioned an O ring or a tube - though this is 2nd hand info, from the past owner. Any suggestion is appreciated - thanks!

Hello, My Jura Impressa C5 steam button returns flashing constantly. What does it mean please ?

Hi. I have a leak with my F7. After watching your instructional videos, I would guess that the problem is going to be the cell membrane regulator. This may sound like a dumb question, but what type (exact name & size, please) of screw driver do I use to remove the screws in the back of the machine? I own a ton of tools, but cannot figure this out.

Hi, brilliant instruction video. Thanks! I'm having an issue with an F9 which is constantly displaying the "tray missing" message even if the tray is installed. I have identified the internal switch but pressing this has no effect except on very rare occasions. I'm guessing that the switch is faulty or needs cleaning. Can you advise how to get at the switch? It looks like I need to remove the pump but I am not quite sure where to start. Many thanks!

My Impressa f60 coffee comes out at 158F (70C) this is not hot enough. What is your suggestion? change the temperature sensor or the water boiler?

Hi. Thank you very much for a super useful video. You have saved me several times over. After I successfully fixed several different issues, I now have a leak from the Fluid Connector coming out of the thermoblock. It is the one with two tubes above each other. My problem is, that in all pictures and diagrams this is made of abs plastic with 3 o-rings and 3 hair pins. But my F50, like in the video above, is made of metal. I replaced the two o-rings for the teflon tubes, but the leak seems to be from the top, where the nut connects the connector to the tube comming out of the Termoblock itself. When I took it apart, it seems to be connected just metal on metal, without any o-ring. How is is supposed to be sealed please? ...I hope I have described it well enough... Thanks for any help

Thx for the video. I was able to fix one of my leaks which was the membrane regulator. But before reassemble I tested and saw that there is a small leak from the steamer wand. I can see where it's leaking but not sure if replacing the o rings will fix the problem. There is a ring on it and two o rings. Suggestions Please??

Where is the fuse?

Thanks for the info. But all the models you listed are most definately not identical as you state.

Great video. My check valve /heating cartridge outlet is leaking. Can it be fixed or does it need replacement? Thanks

Hello! Do you know if the machine have a conector to integrate with a arduino ?

I have a leak that appears to be coming out of the membrane regulator which I've determined - upon my opening the machine - to be corroded. I have a Jura Capresso Impressa F7 that I've maintained well since 2009. How can I be confident that this is the source of the problem before I place a parts order? I can send a video and/or picture of the leak if that helps.

Hi I have a jura impressa E40 the water pump seems not to be working would that be the problem that I get no water and coffee coming out. boiler is also cold. machine goes on normal and sets itself up but then nothing else. Regards tony

lol it’s called a ceramic valve because it’s made of ceramic. I guess when you service these units you fail to disassemble and clean the ceramic valve . That is pretty scary because this is one of the most disgusting parts of the unit and gets very dirty…When you do you will see the 2 piece of ceramic that need to be clean as they are extremely smooth to form a sliding watertight connection .