Key Immobilizer and Remote Programming Using Toyota Techstream Software - Toyota / Lexus

Подписаться 446 тыс.

Просмотров 450 тыс.

50% 1

Here's how to program a new Lexus or Toyota key immobilizer and remote to work with your vehicle.
On newer model Toyota or Lexus vehicles built in the past decade, programming a key requires Toyota's Techstream software. It can no longer be programmed manually using the "pedal dance" method demonstrated here:
• Toyota / Lexus Remote ...
A spare blank master key was purchased from eBay. Since a blank key cannot be inserted into the ignition, its remote and transponder was gutted from the key shell and inserted into the original master key's shell for programming.
Toyota's techstream software uses a special cable to connect to the OBDII port and communicate with your vehicle's ECU. For a demonstration, see this video:
• Toyota Techstream Soft...
Once the key is inserted and turned to the ON position, the key transponder wizard is opened in the techstream software.
Follow the wizard to reinsert the original master key, then remove it, then insert the new blank key, waiting 75 seconds for it to be programmed. The key will then be programmed for the engine immobilizer, though the remote will still have to be programmed separately.
To program the remote, you don't need Techstream software.
Simply follow the instructions to open and close the door a few times and turn the key in the ignition to put it into programming mode. Then press and hold the buttons on the remote and the locks will cycle indicating it has been programmed.
The eBay key purchased worked fine for starting the car, however the remote proved to only work intermittently, so buyer beware. Its better to buy a cheap key shell with a blank blade and a used OEM remote and reprogram it for your car than to use the aftermarket transmitters which are hit and miss.
Link to Etsy shop where you can purchase speedkar99's brother's socks, t-shirts or hoodies:
www.etsy.com/ca/shop/Speedkar
Check out the speedkar99 Facebook page:
/ speedkar9
Check out the speedkar99 Linkedin page:
/ speedkar99
Follow speedkar9 on Instagram for behind the scenes coverage:
/ speedkar9
Subscribe for more videos just like this:
ru-vid.com_...

Авто/Мото

Опубликовано:

10 ноя 2015

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 429

@Captain_911 2 года назад

The best auto mechanic in the world. I will be watching every single your videos. Easy to understand and very helpful. Thanks a lot sir.

@adamo36532 3 года назад

DUDE, you are the first one to point out that the transponder is in the beeper that unlocks the car remotely. I thought it was located under some plastic somewhere. 1:27 saved me from having to buy a cable to use Techstream. I was able to put it next to my old blade off my master key that wouldn't start because I never had the transponder next to it lol. Great video. I just want to tell the viewers that you do not need to use Techstream if you have your master key from before. Ignore every other video if you have a 2004 Lexus es 330 on how to program the transponder. You go in your car with all the doors closed. Next , stick your master key into the ignition 5 times leaving it in at the end. Never turn the key just put it in and out in the off position. Then you open and close your driver side door 6 times while the key is in the ignition. Then you take out your master key (The red security light located under the radio display should not be flashing but be glowing red at this point). You then put your new cut key (The one that you are trying to program the transponder) into the ignition and leave it in, not turning it at all. The red light will start blinking. After around one minute the red light should turn off completely. This indicates that your key has been successfully programmed. You may then take your key out and use it as needed to start your engine. I would recommend pinning this comment to help people

@Kai__S 6 месяцев назад

I can’t for the life of it get my (new to us) 2005 ES330 into key programming mode with the 5 key inserts and 6 door openings. Same with an alternate procedure of hitting the gas pedal 5 times and the brake 6 times. I have 2 reportedly original keys for the vehicle (one with remote fob and 1 without). Might both these keys not be “masters”, like the valet key+card ? Is there a way to tell? My Autel 806 Pro unfortunately doesn’t program keys 😢

@adamo36532 6 месяцев назад

@@Kai__S My valet key is a silver one instead of black and had no remote unlock and I was trying to program with it. I think its different than the other ones because it wont unlock the glove compartment and apparently doesn't have the chip in it that can program new keys. I used the broken original master key to program 2 new keys with the beep unlock. There is a chip inside them that wont start the car unless you activate them using the master key. So when you cut a new key without programming it wont start the car. I am not sure if the new programmed keys can program new keys. Maybe the keys you have were created when the previous owner lost his keys and used a locksmith and then those 2 keys cant make new ones? I am not sure though. When I realized I was using the valet key and finally tried with the master it was really easy.

@Kona5.0 3 года назад

Great video!! The key programming was more simple than the actual key fob lock/unlock. Especially even compared to the long wait time GM requires when programming new keys.

@chriswilson8678 8 лет назад

Thanks for this great tutorial...just bought my daughter a used 06 ES330 but the remote wouldn't lock/unlock the doors...followed your instruction in the last half of the video and now the remote lock & unlocks like new!...and now I'm the best dad ever! Thanks again!

@speedkar99 8 лет назад

+Chris Wilson Glad you got it working, enjoy the ES. I have a 2005.

@blacksun496 5 лет назад

Chris Wilson did you use a text screen cable or whatever he called it? I have no idea what that is!!

@kickbuttowski8201 2 месяца назад

It's techstream cable Also know as obd2 cable @blacksun496

@BarryRnGuitar 4 года назад

Clear, precise and on point. Great work! Thank you!!

@speedkar99 4 года назад

You are welcome

@Kevin-yr7mr 7 лет назад

Thank you so much for this video! My key and chip were separated without a housing so my car wouldn't start even though it's a master key. Turns out the chip needs to be next to the transponder!

@speedkar99 7 лет назад

+Kevin Okinedo It sure does. Glad it helped.

@mradhakrishnan3549 2 года назад

my car not start,key put in the key cilinder security light blinks.what is the solution

@aussiefirestorm 7 лет назад

Works on RX330 also. Thanks so much I had my scan tool for the immobilizer function , but had to use this method for the remote to lock and unlock doors.

@speedkar99 7 лет назад

+aussiefirestorm Thanks, glad it worked out for you, and yes this is similar for all Lexus models before the smart key.

@rotcataergeht 7 лет назад

aussiefirestorm HOW can i reprogram a used rx330 key fob bought from ebay on my rx330? i lost my old key fob while fishing.

@rotcataergeht 7 лет назад

Not working on my 2006 rx330 using techstream version 10.29.30. bought a used rx330 key fob w oem chip from ebay.

@Limeayy 6 лет назад

I have questions, could i just download a newer version of techstream and just download the drivers for the mini VCI and that'll all work out?

@mahmoudhantouli5434 7 лет назад

thank you for your help again I will try today

@wholeNwon 8 лет назад

Some years ago, I wanted an extra transponder key. I provided the key code to an Ebay merchant. He shipped a precut key. I simply programmed it in the car with the master key and everything worked great. The price was good and, more important, I didn't even have to set foot in the Lexus stealership...er...dealership. They could also cut the key based on the VIN #.

@speedkar99 8 лет назад

+wholeNwon I bet you have a previous gen car and programmed it the normal way by pressing the gas pedal and opening the door etc, similar to this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-1aKb96V8A44.html

@wholeNwon 8 лет назад

+speedkar99 Right, it's one of the last series. Great car.

@MYKEYSAUTOMOTIVE 5 лет назад

Amazing freaking video !! Love how you can talk!!!

@speedkar99 5 лет назад

Thanks! What more would you like to see

@rayane454 8 лет назад

Hi, Could you please show me how to program a new smart card for LX570 and can I program a used one using tis tecstream. Thanks

@Omar-on804 4 года назад

thanks a lot this video helped me program my key for 2002 es300.

@speedkar99 4 года назад

Glad it helped!

@jamescc2010 5 лет назад

Tried programmed via Techstream a new used unlock OEM smart key for 2013 Prius, but at the final step after placing a new key next to the power button and beeped, it never registered at the final step after putting it on passenger seat. I suspected a bad used key or low battery voltage? Any advise? I always worked most of the time for other customers(unless the key as bad with it didn't beep at all). It was interested b/c it actually gave me a beep, but not a second beep after placing it on a passenger seat.

@toanphan6774 5 лет назад

Good video. Can you recommend the link to exact key to be purchased on ebay which will definitely work? I see lots of keys there and dont know which one is good. Thank you.

@JamesBrice85 7 лет назад

This video was great for me

@andalebgover1252 6 лет назад

Excellent instructions. This is great software.

@speedkar99 6 лет назад

+Andaleb Gover thank you

@wcolby 5 лет назад

You finally got your thumbs up from me. note: you can’t use the valet key to program. I had to use my back up credit card key to program. great video! thank you

@speedkar99 5 лет назад

You are welcome. Of course the valet wouldn't work, otherwise the valet driver could be doing this to your car!

@MrsBetterthanblessed 5 лет назад

So the valet key won't start the car until you can get the new one programmed?

@wcolby 5 лет назад

MsBetterThanBlessed To clarify, the valet key will start the car. What it will not do is allow other keys to be programmed. The valet key cannot be the source of the permission for programming new keys.

@wcolby 3 года назад

@Henry Luka I have blocked both of your fake accounts.

@bennettlachlan973 2 года назад

you all probably dont give a shit but does someone know of a tool to get back into an instagram account?? I somehow forgot my login password. I would love any tips you can offer me.

@googleuser1684 6 лет назад

You are a God among men! Thank you!

@speedkar99 6 лет назад

+Google User glad it helped

@JoshDunlop1 3 года назад

Thank you for making such a complete and succinct video! This is amazing and helps out a lot!

@camilo11315 7 лет назад

hello great video, I have a es300 2002 lexus. Only with a valet key. ( it can't open the trunk or glove compartment) I bought an aftermarket new key that I cut that seem to be able to open trunk,doors and glove compartment but is not program yet. (it cranks but it doesn't turn on the car) what should I do? the new key looks a bit longer and comes with the three bottoms. I really want to program this key that seems to be a master key. thanks

@peteradegbola4508 8 лет назад

pls in programming the remote,can d existing remote for my former highlander be added to a new highlander.

@thefleaflop 8 лет назад

Thank you for your response. Your are correct,... it should work and probably will work once I get the correct key. My eBay dealer sent the wrong key (electronics). They say the definition of insanity is doing something over and over expecting a different result. I was definitely INSANE yesterday, watching your video and back out to the car..... WoW!!!!! I know now, if I would have done it the way you did it,.... swapping elec. with the shell of the master, I would not have wasted a key cutting....,....

@speedkar99 8 лет назад

+fleaflop ... Yes, but now you can still reuse that key shell with the new eBay electronic guts, right?

@Pimp-lc7vk 8 лет назад

+speedkar99 I only have valet smart key on 2004 Lexus ls 430, can I use techstream to erase code to all existing keys to program my new key as a master key. I have techstream but I'm scared I might erase my only key recognized by my car. Would really appreciate any help!

@wangofree 2 года назад

Excellent video!!

@speedkar99 2 года назад

Thanks

@rotcataergeht 7 лет назад

Do you have video for lexus rx330 key fob programin with immoblilizer chip? i bought used rx330 key fob from ebay lost mine while fishin.

@FD-is1ug 3 года назад

Do I need to purchase an activation key for the tech stream to use it?

@xjssts7127 10 месяцев назад

Excellent video.

@speedkar99 10 месяцев назад

Thank you very much!

@bamnjphoto 5 лет назад

Thanks for this video saved me a fee from Lexus to program my remote

@speedkar99 5 лет назад

Glad it helped

@Alex-cc6ge 8 лет назад

great video thanks to the author of this movie

@wc2006 3 года назад

Its not a movie its a video

@beckyiverson6421 3 года назад

I watched the second half of your video (great presentation by the way)can not program the remote to lock/unlock any tips. Aftermarket keys start the car but for some reason, I am unable to get the fob to program. I have a 2006 Lexus RX400h

@danielcrecco5210 3 года назад

Have you found a solution to this? I have the same problem. Maybe because it is an aftermarket key?

@kCI251 4 года назад

WHAT YEAR Lexus will this procedure work on? I've tried it on my 2010 and cannot get it into programming.

@bac3phi 8 лет назад

awesome video. Thx I just bought a used 2004 ES330 that comes with only one key WITHOUT remote (non-master key). What's the best method to obtain a key with keyless entry?

@speedkar99 8 лет назад

+Phil Nguyen Is your key a valet key or a master key without the remote? Did you get the little key tag with a code on it? To cut the key, the dealer will need the master or the key code (or maybe they can cut from the VIN). However to program new keys, you're going to need a master key. Techstream can delete old keys and add new keys, but only if you had that master key. I think you need a special code from the dealership to put into techstream software to reset the master key if you don't have one.

@sheikhjewel4222 4 года назад

Nice video Sir! I have 3 Teachstream softwer vr14/vr12.

@speedkar99 4 года назад

Welcome

@NewsBroadcasting 3 года назад

Question - i replaced the headunit in a Toyota landcruiser 2000 US 100 series with an android screen , the security light is gone as the android screen connects to HVAC via CANBUS connectors. Can this still work tech stream software?

@888zzz 2 года назад

Is there a chance that if you don't follow the programming procedure correctly that you can make a mistake which will prevent the computer from being able to read the original key and consequently the car cannot be started with the original key? I read this is a possibility at least with some Toyotas. Are there any risks at all with trying to program keys with Techstream?

@racerxone2144 6 лет назад

I only have a valet key. Do you have a video for clearing all keys and reprogramming new master and valet with techstream? thanks

@speedkar99 6 лет назад

+Racerx One see my immobilzer hacking video

@eastvantees4607 4 года назад

Hey will this work if I've lost the master key? i still have the valet 2002 IS300

@artuzumaki8059 6 лет назад

Will this work on Toyota Avensis 2008 SDN Prestige? Thank you.

@kmschn3321 4 года назад

thanks your the best

@liyangtime 6 лет назад

Good video, I only have one slave key for my 2004 Toyota Solara, and am going to get a master new key. as well remove slave key chip. Do you think slave key's chip will help with finishing new master key register?

@speedkar99 6 лет назад

Yes

@ItsReloj 5 лет назад

This worked. Thanks

@speedkar99 5 лет назад

Glad it helped

@SK4869 8 лет назад

it's so easy once you know how. thanks my buddy. your the best, thumbs up #6 :)

@speedkar99 8 лет назад

+SK4869 Thanks

@Alex-cc6ge 8 лет назад

+speedkar99 thanks

@Alex-cc6ge 8 лет назад

+SK4869 Thanks

@Alex-cc6ge 8 лет назад

+SK4869 Thanks

@mahmoudhantouli5434 7 лет назад

hi I need help how you can reprogram the key for 99 Toyota camry after changing the ECM

@speedkar99 7 лет назад

+Mahmoud Hantouli See my immobilizer hacking video.

@romeoloza5026 4 года назад

Gracias brother

@franciscoduarte8249 8 лет назад

Gracias pude hacerlo con mi Lexus RX330 2005! Thanks my friend....

@speedkar99 8 лет назад

+Francisco Duarte Thanks, glad it helped.

@thefleaflop 8 лет назад

yes but the reason I bought the TTS software in the first place was to find out what was going on with my SRS dash light. Its not throwing a code in the software. Does your cable stay green thoughout the scanning process>? I have two cables and both stay red/orange from the time I load the software. Have v8.10 on a laptop and v10 on a desktop and both machines create a orange light with both cables. Can you do a cable check on your system and relay findings? thanks,

@speedkar99 8 лет назад

+fleaflop ... The color of the LED on my cable does not change when it is transferring data regardless if it's plugged into the obd port. What's wrong with the SRS light?

@ItsBloxable 8 лет назад

How would you go about programming a remote for a 2009 Corolla if there is only a start/stop ignition button?

@speedkar99 8 лет назад

+ItsBloxable You could probably use techstream for that. Didn't know the 09 Corolla comes with stop/start.

@kewlnorcaldude 7 лет назад

On my older 97' Lexus GS300 I only have a factory spare, and no original master keyfob...I've never had any problems with immobilizer so if I buy a new blank Key fob from Ebay...can I just program only the door lock features, and just have the key cut duplicate instead?? I already have another aftermarket Viper alarm installed. But would just like a nice key fob all in one.

@speedkar99 7 лет назад

+kewlnorcaldude you can't program with valet key

@kabtamugetu3915 6 лет назад

usefull information thank you

@speedkar99 6 лет назад

+Kabtamu Getu thanks!

@abdomar0528 4 года назад

This won't work on a 99 GS300? I have to use am EEPROM reader correct?

@alexlopez-gh8dl 8 лет назад

Do you know if this will work on a 2015 Toyota Corolla?

@nebilbaqhum2162 7 лет назад

i tried programming the lock/unlock using the same method on a 06 lexus rx400h and after completing the last key on/off.. nothing happens. key is still not programmed. its an aftermarket key.. is it possible the car has reached max number of keys? i tried the 3 key on off to see how many keys programmed using the new key and nothing happens.. thoughts?

@michaelphan3521 6 лет назад

Nebil Baqhum I have the same car and same problem. I've been doing the chicken dance for 1 hour now.

@shameermalik5540 6 месяцев назад

I have the same key shape for my ls 430. I don't like it. Can i buy an aftermarket remote that looks different and then program it the same way?

@katsuramoneh 4 месяца назад

so you’d still need a working key to connect techstream to ecu. you can’t originate w/o a working or master key?

@mzek24 3 года назад

Will this work for 2000 toyota celica gts?

@elijahperez159 6 лет назад

If u only have an engine swap with the immobilizer and everything needed except keys, can you program a key or chip to the ecu to make it run? I need to have this done if there is a way. Like put my ecu in a car and use its organs to program the chip to recognize each other

@speedkar99 6 лет назад

See my immobilzer hacking video

@steverandell8526 7 лет назад

what is the year and model of vehicle used in the video? My 06 RX400h is having difficulty with getting key programmed with techstream...

@speedkar99 7 лет назад

+steve randell 05 es330. Should be the same as yours.

@WilmerJael 7 лет назад

Awesome! I have a question now, I only have the Valet key, no master key, can I reset the ECU using Techstream and programming the keys I bought off ebay?

@speedkar99 7 лет назад

+Wilmer Jael Yes, but you need to enter a code that only dealers have access to a database for to Virginize the chip.

@johnkim1656 4 года назад

@@speedkar99 So if I only have (1) Valet Key, then I must go to the dealer to get it programmed?

@donkaye1297 5 лет назад

Very good video. Thank you for sharing your knowledge and know how. As you said, "Knowledge is power, and by sharing this knowledge we can all learn . . ." More power to you for the good work you do. On another note: Do you have a Video on how to reset the the Anti Theft in a 2004 Lexus RX 330 after the car battery is replaced. The battery died when the car was initially locked, and therefore replaced when the system remembered that it was still locked. That triggered the Anti Theft System. We have since then replaced the battery and are able to disarm and arm (unlock and lock doors) using the Remote Control and the Master Key but can not start the car. We can turn on the ignition but can not start (crank or turn over) the engine. Also the Radio, AC & Fan, and Windows are inoperable. We can only lock, unlock, and turn on the ignition. Do you or anyone know the solution/procedure on how to reset the system. Thank you in advance for your help.

@speedkar99 5 лет назад

You are welcome. I'm not sure how to reset the alarm system Unless if you need to reprogram all the keys...you might need techstream with a locksmith code...

@donkaye1297 5 лет назад

@@speedkar99 Thank you for your response. I still have not found a solution. If you come up with anything, please let me know. Thanks again.

@basil4everx2007 6 лет назад

My friend has a 2003 lexus es 300 and it has a c1336 code and VSC lights are seen on the dashboard ,what could be the problem and how should I fix it ?? Thanx

@speedkar99 6 лет назад

+Basil4everx You might need techstream software for that, or there might be a diagnostic mode. This video shows key programming.

@mirzo9154 5 лет назад

Would you be kind enough to tell what kind of cables been there used by you when work with laptop?

@speedkar99 5 лет назад

If you go on eBay or Amazon and search Toyota techstream usb to OBD2 cable

@thefleaflop 8 лет назад

srs light has been on since purchase (bout 2 months ago). Got it scanned by a mechanic yesterday and code was C-1241 (Low Battery-Positive Voltage). Getting no codes with the TTS software.

@speedkar99 8 лет назад

Low battery voltage can throw a bunch of random codes that make it hard to diagnose. Take your battery to a local auto parts store and have it load tested and replace if necessary.

@Aay-jay989 6 лет назад

For the door locking program... i got mistaken the steps will it affect the key?how many times can i try the procedure?

@speedkar99 6 лет назад

+abed aljabbar it shouldn't affect it. Just open the door and close it and start again

@eopro_ 7 лет назад

@speedkar99 , need help programming the remote for a 2002 toyotal altezza, that's the japanese version of the is200/is300.

@speedkar99 7 лет назад

+Eddy Omar Lora Follow my other Lexus key programming video

@CluelessEngineer 8 лет назад

Good video🚘good quality. 📷 DSLR?

@speedkar99 8 лет назад

+Project DIY Thanks. Partially DSLR and point and shoot, depending on the angle.

@user-xu3ty4wp9v 6 лет назад

очень класное видео

@wilmergonzalez2906 6 лет назад

Can I program a used transponder from another car to be used with my new key (which has no transponder, it's only the blade and the shell)?

@speedkar99 6 лет назад

+Wilmer Gonzalez yes

@efrizalbuyungmasterkeytoyo7747 7 лет назад

good information

@speedkar99 7 лет назад

Thanks

@efrizalbuyungmasterkeytoyo7747 7 лет назад

Any vidio for LC 101 2002 years production . ? I you have . please sent link it . thanks ..

@ae86ptan7 7 лет назад

Will this process work on an IS300 with only the programmed valet key and one non programmed eBay master key?

@speedkar99 7 лет назад

+Patrick Tan Nope you need one master key to add new keys. See my immobilizer hacking video

@mohsengavahi5620 2 года назад

Will this method work for a 2009 RX350?

@Joe333x 4 года назад

You can also program the remote buttons with TechStream much easier using the Main Body ECU Utility.

@speedkar99 4 года назад

Yes

@michaelchu802 Год назад

How ? Any instructions? Thanks ! Nvm, figured it out. Much easier ! Thx

@Joe333x Год назад

@@michaelchu802 i dont remember its been so long but TechStream guides you through what to do

@michaelchu802 Год назад

@Joe333x yes thanks ! Definitely is pretty straightforward.

@torque6389 8 месяцев назад

Thank you for sharing this!

@alram5664 7 лет назад

Are you home Techstream? Do you know if a used Toyota "G" transponder chip can be reprogrammed?

@speedkar99 7 лет назад

You mean a wireless key? I've heard it can be reused but there's a huge workaround.

@nanabebo1 7 лет назад

My friend has a toyota tacoma 2015 base trim that didnt came with wireless remote from dealer. we purchased 2 wireless remote and tried one of your video's instructions of going into program mode opening and closing the door but it didnt worked. After doing researches I saw that I needed to go to a locksmith to enable the wireless remote function in the toyota. can this be done over techstream or do I really need a locksmith?

@speedkar99 7 лет назад

+nanabebo1 Use techstream to enable the wireless function. No need for dealer.

@mathieudore7444 6 лет назад

Worked on a 2008 rx400h. Everything works except the trunk button. Is there a way to program that button? It works on the old remote but not on the new programmed ones. I programmed the remote with techstream

@iceman9292 3 года назад

Same with mine... but for some reason i waited a month or so and now the trunk button works!!

@broseph13 5 лет назад

ive tried techstream 10. something and 12. something, both on 32 bit and 64 bit operating systems, i have a 2013 corolla, ive been able to access main body settings, and program a new remote, change some door unlock settings and light settings. but the immobiliser tab always has a * next to it no matter what ive tried. any ideas?

@speedkar99 5 лет назад

Most likely you don't have an immobilzer

@dridhoc7978 7 лет назад

Hi is the Cable you used is Mini vci ? Does it do every thing considring scaning for errors and reprogrammin keys?

@speedkar99 7 лет назад

+Drid Hoc yes it does

@maatouguimaatougui7698 2 года назад

I want to know where is the emo box in the Toyota Hilux 2021

@muhammadkhresat7004 Год назад

Can you get a Car Key cut with the Vin number

@dreikonse 6 лет назад

Great video! Can you please provide a link for the mini vci cable drivers? My cd that came with it was damaged i cant find them anywhere.. thanks

@speedkar99 6 лет назад

+dreikonse I think you'll have to search online, mine was damaged too and I searched till I found it somewhere...3 years ago.

@dreikonse 6 лет назад

speedkar99 nothing trusted in downloadable material to be found anywhere... if possible can you make a video about it or share your links? Thank you once again

@speedkar99 6 лет назад

+dreikonse see my video description

@lonetraveler5660 2 месяца назад

Is techstream able to program 17 rav4 remote with start button? Thank you

@mannymatias1194 7 лет назад

Will tech stream work if I only have a key with a blank fob not programmed I lost my oem key nothing to program no one from

@speedkar99 7 лет назад

+Manny Matias Yes but you need a locksmith code that the dealer has...

@Mambre79 6 лет назад

How can I get the code apart turning to dealer? Software or tool?

@garikugarik4326 8 лет назад

Hey. Very useful video! Please tell me: is it possible in this way to program a new key for Lexus GX470 2006?

@speedkar99 8 лет назад

+Garik Ugarik Yes you can program most Toyota keys with techstream.

@garikugarik4326 8 лет назад

Hello. Purchased the key on Ebay, - made attempt program him. Turned out to program only the buttons to open / to close. Purchased on Ebay the key is not led by a car, - on the last of peat-time of programming gives out an error. What can reason be in? Does a problem can in radio frequencies of chip?

@speedkar99 8 лет назад

So the remote works but the transponder doesn't? If it is giving you errors in programming it could very well be a defective or incompatible chip. Make sure the serial number on the new one matches the one on the back of the original.

@jamescc2010 5 лет назад

I programmed a smart key on 2010 Lexus RX450 and everything was good except the new key cannot open the truck like the original is. Sometimes this happened on other cars as well but most of the time it worked. Any thoughts?

@speedkar99 5 лет назад

The remote is programmed separately from the smart key to start the car

@jamescc2010 5 лет назад

@@speedkar99 I will check it out. From the past with Toyota smart key programming, one key programming step was enough to also program all remote functions. It could have been due to the refurblished remote my client has as well.

@josephereomala2580 3 года назад

can i use vci to program key for lexus rx300 and highlander 2002 model

@speedkar99 3 года назад

Yeah

@JJ-rd2ef 6 лет назад

Is it possible to reprogram a key if all the keys are lost for a 2001 Lexus gs300?

@speedkar99 6 лет назад

Yes see my immobilzer hacking video

@mahmoudhantouli5434 7 лет назад

good morning thank you for your help but my problem is ECM it's not good any more and I do have mastertech Toyota scanner and I can't do it

@speedkar99 7 лет назад

+Mahmoud Hantouli So you need to replace the ecu and then goto erase keys and enter the technician code to Virginize the chip and program new keys.

@mahmoudhantouli5434 7 лет назад

This car the chip in side the key

@mahmoudhantouli5434 7 лет назад

My friend what can software u used for reprogramming ?

@speedkar99 7 лет назад

+Mahmoud Hantouli Ponyprog

@mahmoudhantouli5434 7 лет назад

Good morning can you please send me pictures of it because I found to many of these tool and I don't know right tool I'm looking for

@wojtekwojtek5285 3 года назад

Thanks You!!!

@JohnCreasy85 6 лет назад

Hi! I got Lexus LS430 02' president with only 1 key( 2 buttons lock/unlock) and I bought other used key from the same model car (3 buttons lock/unlock/trunk) When i turn on smart key option under the steering wheel the green LED works fine but i need to put in key to ignition to start vehicle . When i put used key its show communicate "key is different" My question is can i programm/add the other used keyto this car? Im using TIS Techstream. Can You please help?.

@speedkar99 6 лет назад

+John Creasy check the battery in the working key There is a work around to programming used smart keys online somewhere, its not as straight forward as programming a new one with techstream.

@JohnCreasy85 6 лет назад

speedkar99 bettery is brand new. About work which os somwhere do You fot any idea where is IT? Im searching IT from 2 days and everywhere od the same with close/Open door etc.,etc.,

@MrRaygsr 6 лет назад

Hello, can I reflash my ecu with this program? I have a 2001 IS300

@speedkar99 6 лет назад

+MrRaygsr No, the knockoff version doesn't let you flash ecu.

@TheTransporter1461 6 лет назад

Does the remote lock/unlock programming work an a Toyota RAV4 from 2001 too?

@speedkar99 6 лет назад

+TheTransporter1461 Yes but you probably don't need techstream for such an old car.

@TheTransporter1461 6 лет назад

I tried it, but it didn't work for me. After the steps the vehicle didn't give me the confirm of being in programming mode and I weren't able to program my second key.

@florentinarin7728 5 лет назад

Hi. Could you please put a video how to program Toyota Camry 2009. Thank you

@speedkar99 5 лет назад

Same method

@florentinarin7728 5 лет назад

@@speedkar99 thank you. Probably the keys are not good , bought from e bay

@amyroseblazethecat8807 7 лет назад

that easy key programming this Lexus and Toyota

@speedkar99 7 лет назад

+Raions World The toy foxy - minecraft Wild SFM fnaf yes its easy

@robertmorris1467 6 лет назад

@KitingCakes 3 года назад

Do you have link to purchase cable and software?

@panick.attack 6 лет назад

Worked wonderfully on my 2008 Toyota Rav4! Thanks a ton!

@speedkar99 6 лет назад

+kongology good to know. Did you use techstream to program keys?

@panick.attack 6 лет назад

speedkar99 yes I did.

@ahmedahmed-dt5ew 4 года назад

hello my genuis friend is your techstream firmare 1.4 or 2.0 ?

@gjergjidano5478 6 лет назад

Hello do you know where I can buy the obd2 cable for Toyota highlander 2008 let me know please,thanks

@speedkar99 6 лет назад

+Gjergji Dano eBay Amazon

@aniselrhaffouli9725 4 года назад

Hello Everyone, im from France and i want to change my remote control for my yaris from 2002 made in japan but i don’t now if my remote control works on 315 mhz or 433 mhz ? Thanks

@kentb3175 4 года назад

433 mhz for Europe.

@livewire4216 7 лет назад

hey guy how do I get around the software registration I wasn't given a software key

@speedkar99 7 лет назад

+Andrew Rodgers You need to edit the notepad file from a 0 to a 1

@Techman-pt5zs 7 лет назад

I have seen many clone Techstream on youtube. I don't buy clone scan tools because if it breaks who am I going to call in china for tech support or warranty. I see they are pretty cheap but it won't do any programming. I see it works well for you.

@speedkar99 7 лет назад

The techstream cables work fine for Toyota immobilizer programming. Honda HDS MVCI cables won't work for immobilizer programming though. This cable has paid off for itself, not to mention I can use the techstream software on any OBDII car (there's a global OBDII mode, I tried it last night on my Honda), so I can access all the engine sensors, graph them and record live data.

@alexlopez-gh8dl 8 лет назад

I tried this video and everything worked, I think. After using Techstream my car turns on with any key without a chip needed I don't think it has anything to do with teach stream I just bought the car but why would the car accept any key without a transponder? Did someone setup car ecu that way?

@speedkar99 8 лет назад

If you somehow disabled the immobilizer then yes, it would start with any key. Does the security light blink before u put the key in ignition?